검색결과

검색조건
좁혀보기
검색필터
결과 내 재검색

간행물

    분야

      발행연도

      -

        검색결과 346

        201.
        2009.11 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        We investigated the NO gas sensing characteristics of ZnO-carbon nanotube (ZnO-CNT) layered composites fabricated by coaxial coating of single-walled CNTs with a thin layer of 1 wt% Al-doped ZnO using rf magnetron sputtering deposition. Morphological studies clearly revealed that the ZnO appeared to form beadshaped crystalline nanoparticles with an average diameter as small as 30 nm, attaching to the surface of the nanotubes. It was found that the NO gas sensing properties of the ZnO-CNT layered composites were dramatically improved over Al-doped ZnO thin films. It is reasoned from these observations that an increase in the surface-to-volume ratio associated with the numerous ZnO “nanobeads” on the surface of the CNTs results in the enhancement of the NO gas sensing properties. The ZnO-CNT layered composite sensors exhibited a maximum sensitivity of 13.7 to 2 ppm NO gas at a temperature of 200˚C and a low NO gas detection limit of 0.2 ppm in dry air.
        4,000원
        202.
        2009.07 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        Efforts to reduce noise in industrial application fields, such as automobiles, aircrafts, and plants have been gaining considerable attention while a sound proof wall to protect people from the noise has been intensively investigated by many researchers. In this study, our research group suggested creating a new sound proof wall composed of scrap aluminum chips and perforated plates in a commercial polyester sound proof wall, which was then successfully fabricated. This wall's sound absorption characteristics were measured by an impedance tube method. The sound absorption property was evaluated by measuring the Noise Reduction Coefficient (NRC) to the standard, ASTM C 423-90a. The noise reduction coefficient of the sound proof wall composed of 3.5 vol.% and 7.5 vol.% of scrap aluminum chips relatively increased to 5% and 8% compared to the commercial polyester sound proof wall. The scrap aluminum perforated plate also relatively increased to 13% compared to the commercial polyester sound proof wall.
        3,000원
        203.
        2009.04 KCI 등재 구독 인증기관 무료, 개인회원 유료
        This study was performed to investigate the effects of aluminum sulfate administration on the brain tissues of old rats, when given at different concentrations. The experiment attempted to further ascertain whether aluminum exposure cause Alzheimer's disease. Seventy-five aged Sprague-Dawley rats were divided into five groups; a control group, 2 ppm aluminum sulfate group, 20 ppm aluminum sulfate group, 40 ppm aluminum sulfate group, and 200 ppm aluminum sulfate group, and were kept on the respective diets for 12 weeks. In order to understand the influence of aluminum on the brain, serum aluminum concentrations, phospholipid composition, and catecholamine concentrations were compared between the aluminum-treated groups and the normal group. According to the results, serum aluminum was higher in the aluminum sulfate-treated groups than in the normal group. Within the cortex, catecholamine concentrationes were significantly increased but cerebellum and brainstem tissue were significantly decreased, in the aluminum sulfate-treated groups compared to the normal group. For phospholipid composition, phosphatidyl inositol was significantly increased wherase phosphatidyl choline, phosphatidyl ethanolamine, and phosphatidyl serine were significantly decreased in the aluminum sulfate-treated groups versus the normal group. Based on the data, increased aluminum consumption in experimental animals causes increased serum aluminum levels and catecholamine variation. These phenomena are very similar to conditions of Alzherimer's disease. Therfore, the results of this experiment further suggest that aluminum cause Alzherimer's disease, coinciding with reports that aluminum is a cause of neurofibrilly tangles in the brain.
        4,000원
        204.
        2009.02 KCI 등재 구독 인증기관 무료, 개인회원 유료
        To improve the filtration efficiency of porous materials used in filters, an extensive specific surface area is required to serve as a site for adsorption of impurities. In this paper, a method for creating a hybridized porous alloy using a powder metallurgical technique to build macropores in an Al-4 wt.% Cu alloy and subsequent surface modification for a microporous surface with a considerably increased specific surface area is suggested. The macropore structure was controlled by granulation, compacting pressure, and sintering; the micropore structure was obtained by a surface modification using a dilute NaOH solution. The specific surface area of surface-modified specimen increased about 10 times compare to as-sintered specimen that comprised of the macropore structure. Also, the surface-modified specimens showed a remarkable increase in micropores larger than 10 nm. Such a hybridized porous structure has potential for application in water and air purification filters, as well as membrane pre-treatment and catalysis.
        4,000원
        205.
        2008.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Aluminum nitride (AlN) powders were prepared by the chemical vapor synthesis (CVS) process in the system. Aluminum chloride () as the starting material was gasified in the heating chamber of . Aluminum chloride gas transported to the furnace in atmosphere at the gas flow rate of 200-400ml/min. For samples synthesized between 700 and , the XRD peaks corresponding to AlN were comparatively sharp and also showed an improvement of crystallinity with increasing the reaction temperature. In additions, the average particle size of the AlN powders decreased from 250 to 40 nm, as the reaction temperature increased.
        4,000원
        206.
        2008.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
          Surface roughness is an important factor to evaluate machined parts in precision machining. This is the major measure of surface quality. This research sets up experiments to select the factors which affect surface roughness in the machining of inclined
        4,000원
        207.
        2008.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Aluminum alloys are not only lightweight materials, but also have excellent thermal conductivity, electrical conductivity and workability, hence, they are widely used in industry. It is important to control and enhance the densification behavior of metal powders of aluminum. Investigation on the extrusion processing combined with equal channel angular pressing for densification of aluminum powders was performed in order to develop a continuous production process. The continuous processing achieved high effective strain and full relative density at . Optimum processing conditions were suggested for good mechanical properties. The results of this simulation helped to understand the distribution of relative density and effective strain.
        4,000원
        208.
        2007.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        온실보온을 위한 알루미늄반사단열재의 설치위치와 광택부의 설치방향에 따라 보온효과를 구명하고자 알루미늄반사재와 부직포를 조합하여 모듈을 구성하고, 모듈내 가열량을 각각 100W, 40W로 하여 2차에 걸쳐 처리 건구온도와 흑구온도, 상대습도를 재료의 조합에 따라 분석하였다. 1. 알루미늄반사재가 있는 경우가 부직포만 있는 경우보다 보온효율이 높았으며, 알루미늄을 두 층으로 하면 한 층으로 할 때보다 내부온도가 높았다. 알루미늄반사재를 한 층으로 설치할 때는 알루미늄반사재의 광택부분을 외부로 향하게 하는 것이 내부로 향하게 하는 것보다 모듈내 온도가 높았다. 알루미늄반사재를 두 층으로 할 때는 같은 방향으로 하는 것이 높게 나타났으며 이 경우 광택부를 둘 다 외향으로 배치하는 것이 보온효율이 더 높게 나타났다. 외기온도에 따라 모듈내 건구온도는 전 모듈에서 서서히 상승하며 그 변화의 크기는 외기온도의 변화보다 적었다. 2. 모듈내를 가열하지 않는 경우 모듈내 온도는 모듈간 온도차가 0.5℃를 넘지 않았으며 그 차이를 인정하기 어려웠다. 3. 모듈내의 흑구온도변화는 건구온도변화와 그 경향이 비슷하였다 흑구온도는 대체적으로 건구온도보다 높았으며, 그 경향은 알루미늄반사재광택부가 내향인 경우가 외향인 경우보다 더 강하게 나타났던 바 복사열영향이 큰 것으로 판단되었다. 모듈내 상대습도는 건구온도가 증가하면 비교적 직선적으로 하강하였다.
        4,000원
        209.
        2007.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Characteristics of Al-based composites with waste stainless steel short fiber, fabricated by magnetic pulsed compaction and sintering were investigated. The compacts prepared by magnetic pulsed compaction showed high relative density and homogeneous microstructure compared with that by conventional press compaction. The relative density of sintered composites at for 1 h exhibited the same value with compacts and decreased with increase in STS short fiber content. The reaction between Al and STS phase was confirmed by the microstructural analysis using EDS. The sintered composites, prepared by magnetic pulsed compaction, showed increased hardness value with increasing STS fiber content. Maximum yield strength of 100 MPa and tensile strength of 232 MPa were registered in the AI-based composite with 30 vol% STS short fiber.
        4,000원
        210.
        2007.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        알루미늄 분말야금부품은 철계 분말부품에 비해 가볍고 알루미늄 주조부품에 비해 우수한 기계적 물성을 갖는다. 단, 상대적으로 비싼 가격이 이 부품의 응용을 제약하는 장벽이었으나 최근의 환경과 에너지 문제에 대한 세계적인 관심은 이를 극복할 수 있는 계기를 제공하고 있다. 선진국은 이미 일본을 중심으로 1990년대부터 알루미늄 분말부품에 대한 기술개발을 진행하였고 현재는 다양한 상용 부품을 판매하고 있으며 조만간 그 판매량이 크게 증가할 것으로 예상된다.
        4,000원
        211.
        2007.11 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        Both photoluminescence and thermal characteristics for SrAl2O4:Eu+2,Dy+3 phosphors synthesizedwith various aluminum compounds (α-Al2O3, γ-Al2O3, amorphous-Al2O3 and Al(OH)3) were investigated in thisstudy. The formation temperature of the host SrAl2O4 crystal is changed by these various aluminumcompounds, as a result of the different thermal decomposition temperature of SrCO3 phase. Among thesecompounds, the amorphous-Al2O3 phase shows the lowest formation temperature of the host SrAl2O4 crystal.The PL emission and excitation spectra of SrAl2O4:Eu+2, Dy+3 phosphor are not affected by these aluminumcompounds. After the removal of the Xenon lamp excitation (360nm), however, the excellent long-phosphorescent property of the phosphor is obtained by the amorphous-Al2O3 phase, although the decay timefor all phosphors decrease exponentially.
        4,000원
        212.
        2007.09 KCI 등재 구독 인증기관 무료, 개인회원 유료
        본 논문은 선박용 알루미늄 합금에 대하여 TIG, MIG 그리고 로봇을 이용한 용접 등과 같은 다양한 용접기술을 적용하여 기계적 특성을 평가하였다. TIG 용접을 실시하였을 경우는 항복강도, 인장강도 그리고 연신율은 모재에 비하여 각각 83.9%, 64.6% 그리고 21.9%를 나타냈다. MIG 용접은 ER5356 용접봉을 사용하여 용접한 경우 ER5183 용접봉을 사용한 경우에 비하여 기계적 특성이 대략 2-4% 정도 개선된 효과가 관찰되었다. 또한 로봇을 이용한 용접을 실시한 경우는 5456-H116 모재에 비하여 5083O 모재의 경우가 양호한 기계적 특성을 나타냈다.
        4,000원
        214.
        2006.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Aluminum nitride (AlN) nanopowders with low degree of agglomeration and uniform particle size were synthesized by carbothermal reduction of alumina and subsequent direct nitridization. Boehmite powder was homogeneously admixed with carbon black nanopowders by ball milling. The powder mixture was treated under ammonia atmosphere to synthesize AlN powder at lour temperature. The effect of process variables such as boehmite/carbon black powder ratio, reaction temperature and reaction time on the synthesis of AlN nanopowder was investigated.
        4,000원
        216.
        2006.09 KCI 등재 구독 인증기관 무료, 개인회원 유료
        To provide an aqueous rust inhibitor for metalworking lubricant having low toxicity and excellent rust resistance, we synthesized diester of malonic acid by three consecutive esterifications with over 98% of conversion. This substituted malonic diester could be used as an additive to mineral oil based metalworking lubricant. These metalworking lubricant compositions were showed excellent rust resistance and suitable for various metals and different metalworking processes including hot rolling and cold rolling of aluminum and aluminum alloys.
        4,000원
        217.
        2006.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Aging characteristics and mechanical properties of commercial 7xxx series Al composites were investigated from viewpoint of ceramic contents. After sintering process, sintered densities of blended and composite powder were 95 and 97%, respectively. Each part was solution-treated at for 60 min and aged . And two-step aging was also performed form . The aging behavior of the sintered composite pow-der was different from that of sintered blended powder. The peak aging time of the composite was rapid as well due to strain. Before aging, mechanical properties of sintered composite powder was significantly higher than that of sintered blended powder. These increments of properties were directly affected by ceramic particles. However, after aging, incremental rate of mechanical properties was slowed in the composite
        4,000원
        218.
        2006.04 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Aluminum hydroxides were synthesized by a simple electrolytic reaction of aluminum plates. The aluminum hydroxide, boehmite (AlO(OH)), was predominantly formed in the application of electrical potential at and above 30V, while the mixture of bayerite () and boehmite (AlO(OH)) phases were formed below 20V. The boehmite has a clear fibrous structure controlled on nanometer scale. On the contrary, the bayerite consists of the typical hourglass or semi-hourglass shaped coarse crystals as a result of aggregation of various crystals stacked together. The specific surface area of the boehmite nanofiber was markedly high, approaching at about .
        3,000원
        220.
        2006.03 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        한국원자력연구소 내의 연구용 원자로(TRIGA II, III) 해체 시 발생한 방사성 알루미늄 해체 폐기물의 감용 및 제염 특성을 평가하기 위해 아크로에서 알루미늄의 용융 특성 및 방사성 핵종의 분배 특성에 대한 연구를 수행하였다. 알루미늄 폐기물은 흑연전극(graphite electrode)을 이용한 전기아크로에서 4가지 종류의 플럭스를 함께 첨가하여 용융시켰다. 또한 알루미늄의 용융 시 방사성 핵종의 분배 특성을 고찰하기 위해 알루미늄 시편에 방사성 모의 핵종인 코발트, 세슘, 스트론튬의 화합물을 오염시킨 후 혹연도가니에 넣어 알루미늄 용융실험을 수행하였다. 전기아크로에서 알루미늄의 용융실험을 수행한 결과 플럭스의 종류에 따라 다소 차이는 있으나 플럭스의 첨가에 의해 알루미늄 용융체의 유동성이 증가됨을 확인할 수 있었다. 아크 용융에 의해 생성된 슬래그의 발생량은 플럭스 A와 B를 첨가한 알루미늄 용융실험에 비해 플럭스 C와 D를 첨가한 실험에서 상대적으로 많은 양이 생성됨을 알 수 있었으며, 첨가된 플럭스의 양이 증가할수록 이에 비례하여 슬래그의 발생량이 증가함을 알 수 있었다. 슬래그(slag)의 XRD 분석을 통해 방사성 핵종이 주괴에서 슬래그 상으로 이동한 후 슬래그를 구성하고 있는 산화알루미늄과 결합하여 안정한 화합물로 슬래그 상에 포집됨을 알 수 있었다. 알루미늄 폐기물의 용융시 Co의 분배율은 플럭스를 첨가한 경우에 보다 높은 제염계수를 나타냈으며, 모든 플럭스에서 40% 이상의 제염 효과를 나타내었다. 반면에 휘발성 핵종인 Cs과 Sr은 주괴로부터 98% 이상이 제거되어 대부분이 슬래그상과 분진으로 이동되는 특성을 확인할 수 있었다.
        4,000원