본 논문에서는 해양산업시설 현황과 규제법규 체계, 그리고 이들 시설의 위험유해물질 배출실태 등을 분석하고, 이에 따른 규 제체계의 개선방향을 제시하였다. 분석결과 2020년말 현재, 해양환경관리법의 적용을 받는 해양산업시설은 약 1천1백여개소에 이르는 것 으로 파악되고 있다. 이들 해양산업시설로부터 배출되어 해양유입 가능성이 높은 위험유해물질은 190여종으로 추정되며, 이중 해양유입의 가능성이 가장 높은 물질은 수계로 배출되는 것으로 파악된 20여종으로 추정된다. 그러나 관련 법규정의 미비로 인하여, 배출되는 물질이 예외적 배출물질에 해당하는지 여부를 명확히 판단하기가 어려워, 현장에서의 효과적인 규제집행에 어려움을 겪고 있는 실정이다. 이에 해양환경관리법의 예외적 배출기준과 해당 물질의 종류에 대해 명확히 규정해야 하며, 예외적 배출물질을 무엇으로 할 것인지를 결정할 선정체계와 물질의 위해성 평가체계, 그리고 관련 위험유해물질의 배출정보수집 및 모니터링체계를 명확히 해야 한다.

Cooking, especially meat and fish grilling, is one of the representative sources of indoor and outdoor particulate matter (PM). Most of PM emitted from cooking is ultrafine dust (PM2.5). Since odorous organic acids, aldehydes, and volatile organic compounds are absorbed by PM and discharged, restaurants and food service industries are major sources of odorous PM emission that cause odor nuisance complaints in cities. PM emitted from cooking also contains polycyclic aromatic hydrocarbons (PAHs), which are carcinogens. In this paper, the domestic PM emission status of biomass combustion, especially meat and fish grilling, was analyzed temporally and spatially. The results of previous studies on PM emission concentrations, emission rates, emission factors and their compositions from cooking were comprehensively summarized. In addition, the effects of food ingredient types, cooking methods, seasoning and oil addition and fuel types on the PM emission were reviewed. Much more PM was produced when cooking with charcoal rather than electricity or gas. The higher the fat content of food ingredients such as intestines, the higher the PM emission concentration and emission rate. There was a difference in the PM emissions depending on the cooking oil types, and the PM emission concentration was high when olive oil or corn oil was used. It is necessary to accumulate more information through followup studies on the emission concentrations, emission factors and properties of PM emitted from cooking activities. This information can be used for controlling odorous PM in restaurants and food service industries, and predicting the impacts of odorous PM on air quality and human health.

In this study, blending oils of diesel oil and butanol were used as fuel oil for diesel engine to measure combustion pressure, fuel consumption, air ratio and exhaust gas emission due to various operating conditions such as engine revolution and torque. Using these data, the results of analyzing the engine performance, combustion characteristics and exhaust emission characteristics such as NOx (nitrogen oxides), CO2 (carbon dioxide), CO (carbon monoxide) and soot were as follows. The fuel conversion efficiency at each load was highest when driven in the engine revolution determined by a fixed pitch propeller law. Except 30% butanol blending oil, fuel conversion efficiency of the other fuel oils increased as the load increased. Compared to diesel oil, using 10% and 20% butanol blending oil as fuel oil was advantageous in terms of thermal efficiency, but it did not have a significant impact on the reduction of exhaust gas emissions. On the other hand, future research is needed on the results of the 20% butanol blending oil showing lower or similar levels of smoke concentration and carbon monoxide emission rate other than those types of diesel oil.

본 연구에서는 곡물건조기의 사용 연식에 따른 이산화탄소 배출농도 차이를 비교함으로써 농업 분야의 온실가스 배출 현황을 파악하고자 한다. 사용 연식의 기준을 5년 이하, 6-10년, 10년 초과의 3단계로 구분하였고, 간헐 포집 방법을 선택하였다. 포집 방법은 EPA Method 18에 해당하는 방법론을 따라 수행하였으며, 이는 흡입장치가 음압을 이용하여 간헐적으로 포집하는 원리이다. 포집 장치에 연결되는 보관 용기는 모든 기체에 우수한 차단성이 있어 화학적으로 안정한 테드라백을 사용하였다. 포집 된 가스는 미량분석용인 Gas Chromatograph System을 사용하여 분석하였으 며, 이산화탄소 배출농도 분석결과 평균적으로 5년 이하는 847.4423μ㏖/㏖, 6-10년은 919.2811μ㏖/㏖, 10년 초과는 1137.8560μ㏖/㏖으로 분석되었다. 이산화탄소 배출에 차이가 있는지 검증하기 위해 유의수준 0.05로 일원분산분석을 수행하였다. 분산분석의 결과 연식이 비슷한 그룹 간의 배출농도의 차이가 없다고 나타났지만, 이는 연식의 차이가 크지 않을 때 그룹 간의 비교에 대해서는 더 많은 표본이 필요할 것으로 판단되며, 연식의 차이가 큰 그룹 간의 배출농도에 유의한 차이가 있다고 나타났다.

This study was conducted to assess the effect of acidification of pig slurry on nitrogen (N) mineralization and its environmental impacts during pig slurry fermentation. Different inorganic and organic acids were used to acidify pig slurry. Four treatments including non-acidified pig slurry (control), pig slurry acidified with sulfuric acid, lactic acid, and citric acid were allocated with three replications. The total N content in the acidified pig slurry was higher than non-acidified pig slurry after fermentation. Acidification tended to increase total N content in pig slurry. Ammonium N (NH4 +-N) released from pig slurry was obviously increased at 7 days after incubation, representing 61.4%, 36.8%, and 37.4% increase in the acidified pig slurry with sulfuric acid, lactic acid, and citric acid, respectively. Nitrate N (NO3 --N) in the acidified pig slurry with sulfuric acid was the highest throughout the experiment period, but non-significant effect of organic acid. A large portion of ammonia (NH3) emission occurred within 10 days, corresponding to more than 55% of total NH3 emission. Total cumulative NH3 emission during the experimental period was lower 91% (2.9 mg N kg-1), 78% (7.3 mg N kg-1), and 81% (6.2 mg N kg-1) in the acidified pig slurry with sulfuric acid, lactic acid, and citric acid, respectively, than non-acidified pig slurry (32.7 mg N kg-1). These results suggest that acidification of pig slurry (particularly with sulfuric acid) can be faced as a good strategy to reduce NH3 emission without depressing the mineralization process.

The concern on the greenhouse gas emission is strongly increasing globally. In fishery industry section, the greenhouse gas emissions are an important issue according to The Paris Climate Change Accord in 2015. The Korean government has a plan to reduce the GHG emissions as 4.8% compared to the BAU in fisheries until 2020. Furthermore, the Korean government has also declared to achieve the carbon neutrality in 2050 at the Climate Adaptation Summit 2021. However, the investigation on the GHG emissions from Korean fisheries did not carry out extensively. Most studies on GHG emissions from Korean fishery have dealt with the GHG emissions by fishery classification so far. However, follow-up studies related to GHG emissions from fisheries need to evaluate the GHG emission level by species to prepare the adoption of environmental labels and declarations (ISO 14020). The purpose of this research is to investigate which degree of GHG emitted to produce the species (hairtail and small yellow croaker) from various fisheries. Here, we calculated the GHG emission to produce the species from the fisheries using the Life Cycle Assessment method. The system boundary and input parameters for each process level are defined for the LCA analysis. The fuel use coefficients of the fisheries for the species are also calculated according to the fuel type. The GHG emissions from sea activities by the fisheries will be dealt with. Furthermore, the GHG emissions for producing the unit weight species and annual production are calculated by fishery classification. The results will be helpful to understand the circumstances of GHG emissions from Korean fisheries.

본 연구에서는 광화학 대기질 모델인 CMAQ을 활용해 화력발전소 배출량 제거에 따른 O3 농도의 변화 특성을 분석하였다. 하동 화력발전소를 대상으로 주변 지역의 O3 농도 변화에 대한 발전소 배출량의 영향을 조사하기 위해 하 동 화력발전소의 배출량 제거 전과 후의 CMAQ 수치 모의를 수행하였다. 수치 모의 결과 O3의 주요 전구 물질인 NOx (-18.87%)와 VOCs (-11.27%)의 농도가 감소한 반면에 O3 (25.24%)의 농도는 증가한 것으로 나타났다. 화력발전소 배출량 제거로 인한 NO와 O3 농도의 상대적인 변화를 비교해 본 결과 높은 음의 상관관계(R= -0.72)를 나타내는 것이 확인되었다. 이러한 결과는 O3의 농도 증가가 NO 농도 감소로 인한 O3의 적정 효과 완화로 설명 될 수 있음을 의미한 다. 해당 지역의 O3의 농도 증가가 NO의 농도 감소에 주로 영향을 받은 이유는 해당 지역이 VOC-limited (i.e., NOxsaturated) 지역이기 때문으로 분석되었다. 이러한 결과는 특정 지역의 O3의 농도가 단순히 배출량의 증감에 따라 비례하게 나타나지 않을 수 있다는 것을 암시한다. 따라서 화력발전소 배출량 저감 조치로 인한 대기 중 O3 농도 개선 효과를 정확히 예측 및 평가하기 위해서는 지역 별 O3의 생성 및 소멸 기작에 대한 심도 있는 이해가 필요하다.

국내 고농도의 초미세먼지 발생 빈도 증가와 함께 그 전구물질인 NH3와 관련한 연구가 활발히 진행 중이다. NH3 배출에 있어 농업의 기여율이 높은 것은 자명한 사실이다. 그러나 비료 사용이 농경지 대기 중 NH3 농도에 장기간 미치는 영향에 관련한 연구는 미비한 실정이다. 따라서 본 연구에서는 수동식 NH3 확산형 포집기를 활용해 11개월 간 농경지 대기 중 NH3 농도를 관측하였다. 그 결과 비료 살포 직후 한 달 동안 NH3 배출의 영향이 가장 큰 것으로 나타났다. 그 이후 여름철 기온 상승으로 NH3 휘발이 촉진되어 대기 중 농도가 증가할 것으로 예상하였으나, 54일간의 지속적인 강우로 인하여 대기 중 높은 암모니아 농도는 관측되지 않았다. 그 후 NH3 농도는 가을과 겨울을 거치면서 점차 감소하였다. 비료의 영향력이 감쇠한 시점 이후에는 기온이 감소할수록, 그리고 강수량이 증가할수록 NH3 농도는 감소하는 것을 상관분석을 통해 확인할 수 있었다. 종합해 보면, 국내 NH3 배출량에서 비료의 기여율을 연구하는 데 있어 비료 살포 직후 최소 한 달 동안은 집중적으로 살펴보아야 할 것이며, 현장 연구 시 강수량과 무강우 일수 등의 기상 정보도 함께 고려해야 할 것이다.

The objective of this study is to identify the emission characteristics of VOCs from small-scale painting facilities, such emissions being pollutants that impact nearby living areas and to devise improvement measures to enhance management plans regarding pollutant emissions from painting facilities. VOCs emissions from painting facilities were estimated according to Clean Air Policy Support System (CAPSS) data based on the National Institute of Environmental Research (NIER)'s emission list in 2017. Three automotive painting facilities in Seoul were chosen for evaluation of the adsorption system. We analyzed the characteristics of VOCs generated by type of different operation and measured the removal efficiency of the adsorption system. Therefore, we analyzed current emissions of VOCs from automotive painting facilities based on field measurements. According to such detailed analysis, a systematic management plan was proposed.

The emission of particulate matter and volatile organic compounds (VOCs) from a motor vehicle painting booth was quantitatively evaluated. Most particulate matter was emitted during the spraying process, in which the PM10 concentration was 16.5 times higher than that of the drying process. When the paint was being sprayed, the particles with a diameter of 1.0~2.5 μm accounted for 39.4% and particles greater than 2.5 μm in diameter accounted for 30.6% of total particles. On the other hand, small particles less than 0.5 μm in diameter accounted for 52.4% of total particles during the drying process. In contrast to the particulate matter, high concentrations of VOCs were emitted during both spraying and drying processes. Butyl acetate, xylene, toluene, and m-ethyltoluene were the most abundant VOCs emitted from the motor vehicle painting booth. Additionally, xylene, butyl acetate, toluene, and 1,2,3-trimethylbenzene were the dominant ozone precursors. Especially, xylene exhibited the highest ozone production contribution (32.5~44.4%) among 34 species of the ozone precursors. The information obtained in this study can be used to establish a suitable management strategy for air pollutants from motor vehicle painting booths.

This study is a basic study to improve fuel economy and reduce harmful emissions from passenger cars. This study is a basic study to evaluate the performance of fuel oil additives. The performance may vary depending on the type of engine, the region of use, and the driving habits of the user. Therefore, there are many difficulties in carrying out the test analysis by the objective experimental method while maintaining the same conditions. Therefore, this study intends to examine in terms of securing objectivity as a comparative study by the measurement of single user for a long time. As a result, in the case of cars using gasoline engines, the fuel economy tended to a little decrease as the distance-age increased. However, in the analysis of diesel vehicles by year, it increased gradually after the 5th year and the distance-age of 60,000km. And a comparison of the last three years, an increase of about 3.1% from 12.44km /ℓ to 12.82km /ℓ.

PURPOSES : The purpose of this study is to measure and analyze the fugitive dust generated by each process through field tests to develop a technology to reduce fugitive dust generated during excavation-restoration work on road pavements. METHODS : The testbed was constructed based on a typical excavation-restoration construction section and comprised five sections for reproducibility and repeated measurements. The excavation-restoration work was divided into pavement cutting, pavement crushing, pavement removal, excavation, and restoration processes and fugitive dust generated by each process was measured. Fugitive dust (TSP, PM10, PM2.5, and PM1) was measured using a GRIMM particle spectrometer, which applies the principle of a light scattering spectrometer and can be measured in real-time. RESULTS : Analyses of the average mass concentration of PM10 generated by the excavation-restoration process are as follows: 1286.3 μg/m³ from pavement cutting, 246.8 μg/m³ from pavement crushing, 697.0 μg/m³ from pavement removal, 747.9 μg/m³ from excavation process, and 350.6 μg/m³ from the restoration process. In addition, the average particle size distribution of the excavationrestoration construction was in the order of PM10~PM2.5 (67 %), PM1 or less (24 %), and PM2.5~PM1 (9 %). The pavement cutting process is characterized by the emission of high concentrations of fugitive dust over a short time, compared to other processes. The pavement crushing process has the characteristic of steadily generating fugitive dust for a long period, although the emission concentration is small. CONCLUSIONS : In this study, it was found that the concentration and characteristics of fugitive dust generated during road pavement excavation-restoration works vary by process and the reduction technology for each process should be developed accordingly.

본 연구는 점오염원인 하수종말처리장으로부터 배출되는 물의 수질을 분석하고 배출수의 영향을 받는 어류 중 지점들에서 공통적으로 출현하는 어종인 피라미 (Z. platypus) 를 선택하여 조직학적 변화를 참조하천 지점의 수질과 어류 조직을 비교·분석하였다. 2019년 6월 27~28일 하수종 말처리장 4곳 (대전, 전주, 청주, 익산)의 채집 결과, 참조하 천에서 22종 450개체로 가장 많은 종수 및 개체수가 확인 되었다. 지점별로 5개체씩 2~3년생 피라미의 조직표본을 제작하여 아가미와 근육조직 (피부조직)을 관찰한 결과, 참조하천을 제외한 나머지 지점의 조직은 병리적인 양상을 나타내었다. 수질분석 결과, 각 WTP에서는 배출수질 기준을 준수 혹은 더 좋은 수질로 방류하고 있었다. 그러나 하수종말처리수 배출수 및 방류수계 수질에서 오염도지표를 나타내는 항목인 BOD, COD, TP, TN, SS 값이 참조하천에 비해 높은 것으로 나타났다. 빈약한 어류상과 바이오마커로 이용된 종의 조직병리학적 상태는 참조하천에 비해 낮은 수질에서 기인한 것으로 추측되며, 따라서 원인이 되는 하수종말처리장 배출수 수질개선이 이루어져야 할 것으로 사료된다.

In this study, actual odor conditions were investigated in restaurants, livestock facilities, and major odor discharge facilities around daily life, and an odor modeling program was performed to find ways to improve odors in odor discharge facilities. The odor modeling results of restaurants around daily life showed that the complex odor concentration of large restaurants, which are close to residential areas, is higher than the acceptable complex odor standard at the receiving point. It was judged that a plan to increase the height of the restaurant odor outlets and a plan to reduce the amount of odor discharge was necessary. As a result of modeling the life odor of livestock housing facilities, when the distance from the housing facility is far away, the actual emission concentration is much lower than the acceptable emission concentration at the receiving point. It was judged that such facilities need to be reviewed for ways to reduce the emission of odorous substances, such as sealing the livestock housing facilities or improving the livestock environment. The main odor emission business sites that show complex odor concentration as 1,000 times or greater than the outlet odor emission standard were businesses associated with surfactant preparation, compounded feed manufacturing, textile dyeing processing, and waste disposal. Due to the separation distance and high exhaust gas flow rate, it was found that odor reduction measures are necessary. In this study, it was possible to present the allowable odor emission concentration at the discharge facilities such as restaurants, livestock houses, and industrial emission facilities by performing the process of verifying the discharge concentration of the actual discharge facility and the result of living odor modeling. It is believed that suitable odor management and prevention facilities can be operated.

The correlation among gaseous air pollutants (odorous compounds, greenhouse gases) and meteorological parameters was analyzed in-depth using measurement data at a barn and ambient in a naturally ventilated dairy farm. Both concentration and emission data (loading rate and emission rate), which more accurately express the actual pollutant emissions, were used in the correlation analysis. Gaseous air pollutants (ammonia, hydrogen sulfide, carbon dioxide, nitrous oxide, methane) and meteorological factors (relative humidity, temperature, wind speed, solar strength) were measured for one week in July 2013. The upper and lower outliers of measured data by inducing 1.5 times the interquartile range (IQR) were eliminated. After eliminating the outliers and grouping according to data magnitude, the correlation analysis among gaseous compounds and meteorological factors was conducted using the average values of each group. In the correlation analysis, data for the emission rate (barn) and the loading rate (ambient) showed a better correlation than concentration data. Gaseous air pollutants except for hydrogen sulfide in the barn showed a good correlation. Hydrogen sulfide might not be produced from manure or animal origin. Rather, the compound may be produced by flushing water, which was flushed at periodical times (every six hours). Ammonia emissions increased with increasing temperature, and this increase can be affected from greater exertion of feces by frequent water drinking in a high-temperature condition. In the ambient, the correlation for all gaseous air pollutants was better than that in the barn, because those air pollutants from manure, animals, and flushing water origins were sufficiently mixed in the atmosphere. Wind speed also showed a good correlation with all gaseous air pollutants.