선박에서 호흡성 심정지가 발생하거나, 장시간 심폐소생술을 하는 경우, 가슴압박소생술이 아닌 구조호흡을 동반한 심폐소생 술이 요구된다. 이에 선박은 산소 공급을 위한 구조호흡 장비를 보유하고 선원들은 이를 사용할 수 있는 해기능력을 갖추어야 한다. 본 연구는 선박 내 구조호흡 장비 활용을 높이기 위하여, 선박의 구조호흡 장비 설치 현황과 선원의 사용의향을 분석하여 개선방안을 제시 하기 위한 조사연구이다. 2023년 2월 2일부터 4월 21일까지 진행하였으며, 총 340명을 대상으로 조사하였다. 수집된 자료는 SPSS WIN 23.0 프로그램을 이용하여, 빈도와 백분율, 카이제곱 검정으로 분석하였다. 연구결과, 직책에서 항해사와 선장, 근무부서에서 갑판부, 항해구역 에서 외항선 선원이 선박에서 구조호흡 장비를 많이 확인한 것으로 분석되었다. 선원의 구조호흡 장비에 사용의향은 낮았고, 주요 저해요 인은 사용방법을 모르는 것이었다. 연구대상자의 일반적 특성 중 직책이 항해사, 선장, 근무부서는 갑판부, 항해구역은 외항, 총톤수 2만 톤 이상인 경우, 구조호흡 장비에 대해 사용의향이 높았다. 그리고 구조호흡의 필요성을 알고, 실습과 장비 교육을 받은 선원이 구조호흡 장비 사용에 적극적인 것으로 나타났다. 따라서 모든 선박이 구조호흡 장비를 갖출 수 있도록 제도 마련이 되어야 하고, 선박 내에서 구 조호흡 장비에 대한 접근성을 높이는 환경조성이 필요하다. 또한 구조호흡 장비에 대한 실습과 장비 교육 기반의 교육체계를 구축하여 선원이 해기능력을 갖추도록 해야 한다.

The purpose of this study is to provide lessons learned in the experience of improvement work of fuel handling equipment at operating nuclear power plants. The upgrade of fuel handling equipment for safety enhancement and performance improvement has been going on for 15 years since the early 2000’s. The main goal is to increase fuel loading/unloading capability of the equipment from about 2.5 fuel assemblies per hour to more than six (6). It is achieved with sequential operations of three (3) fuel handling equipment, which consists of the refueling machine, the fuel transfer system and the spent fuel handling machine. The scope of the upgrade for fuel handling equipment is summarized as follows. The PC data control system based on PLC for interlocks and high speed motor drive system is introduced for better operating efficiency. The motors and drives for bridge, trolley, and hoist are replaced with AC servomotors and drivers, respectively. The fuel transfer system has an auto-initiation feature operating from the refueling machine or the spent fuel handling machine. The winch motor and drive for the carriage of fuel transfer system is also replaced with AC servomotors and drivers. And some of HPU (hydraulic power units) equipment for each building (reactor containment building and fuel handling building) are replaced to improve their function. The considerations for improvement of fuel handling equipment are as belows. 1) Fuel handling should be consistent with the instructions provided by the fuel designer and/or manufacturer, which are for Standard type fuel and Westinghouse type fuel, used in domestic nuclear power plants. Each fuel has unique design characteristics, which are PLC setpoints for overload and underload, slow speed zones for a bridge, trolley and hoist, allowable acceleration/deceleration value in handling, hoist elevation and manual speed in off-index operation at reactor. 2) The interlock system should be designed in accordance with design criteria specified by the utilities of nuclear power plant. 3) Performance should be improved according to the operating characteristics of the fuel handling equipment. High-speed and optimization of FTS upender and carriage are essential for operating performance so that its modification should be considered first. And the low speed and range in the operation mechanism of the hoist should be designed to comply with guidelines. 4) The accident analysis through self-diagnosis function and operation history in modification at domestic operating nuclear power plants would be good lessons learned. It is advisable to utilize such various information as it can help to improve reliability of nuclear fuel handling operation and power plant operation rate.

In advanced countries, various policies are being enforced to reduce equipment noise level at it’s source. This paper analyses the problems of domestic noise policies related to noisy equipment, and presents a plan for improving the implementation of expansion policy of low noise equipment based on this analysis. This paper proposes that the equipment satisfying the compulsory rule be able to use the environmental certification mark, the standards of which are defined in recommended rules, to improve the linkage between the two policy measures. This paper also suggests expanding the range of equipment to be supervised and using new noise label that has grades and shows detailed noise level of the equipment to improve environmental certification system. In addition, supplementing the construction permission system and supporting international certification system are offered to expand the use of low noise equipment.

Pilot Aptitude Research Equipment (PARE) is a simulator developed to measure or research pilot aptitude and train for student pilots. Design of an ergonomic PARE operation console is required to operate the equipment effectively. This study carried out five steps : (S1) operator questionnaire survey, (S2) anthropometric design formula development, (S3) usability evaluation, (S4) improvement design, and (S5) validation considering both Physical User Interface (PUI) and Graphic User Interface (GUI) of PARE operation console. The operator questionnaire surveyed needs for each PUI and GUI part of the console from two PARE actual operators. In terms of PUI, the anthropometric design formula was developed by using design variables, body dimensions, target population characteristics, and reference posture related to the PARE console. In terms of GUI, the usability evaluation was conducted by three usability testing experts with a 7-point scale (1 : very low, 4 : neutral, 7 : very high) on GUI of the PARE operation console by seven usability criteria. The improved PARE operation console was designed to reflect the optimal values of design variables calculated from design formula, the results from usability testing, and the operator’s needs. The improvement effect was observed by 20 people who had experience with the PARE operation console. As a result of the validation, monitor visibility and cockpit visibility for the improved PUI design and visibility and efficiency for the improved GUI design were significantly increased by more than 90% respectively. The improved design of the PARE operation console in this study can contribute to enhance operation performance of the PARE.

To ensure the safety and functionality of a railroad bridge, maintaining the integrity of the bridge via continuous structural health monitoring is important. However, most structural integrity monitoring methods proposed to date are based on modal responses which require the extracting process and have limited availability. In this paper, the applicability of the existing damage identification method based on free-vibration reponses to time-domain deflection shapes due to moving train load is investigated. Since the proposed method directly utilizes the time-domain responses of the structure due to the moving vehicles, the extracting process for modal responses can be avoided, and the applicability of structural health evaluation can be enhanced. The feasibility of the presented method is verified via a numerical example of a simple plate girder bridge.

Accompanied with the industrial development, and enlarging and heightening buildings, building equipments are also enlarging. These changes are serious to the cause of structure noises. The Floating Floor System which uses the soft foam polyurethane are becoming popular in construction areas for its short construction period and well vibration proof ability, hence it is becoming wide in the marketing volume. We were able to enhance the physical characteristics of the vibration proof polyurethane mat with this study. As a result, we were also able to secure material competitiveness by meeting the requirements of customer satisfaction through enhancement in estimated material lifetime and physical characteristics.

A number of plating companies have been exposed to the risk of fire due to unexpected temperature increasing of water or other reasons in a plating bath. Since the companies are not able to forecast the unexpected temperature increasing of plating bath and most of raw materials in the bath have low ignition temperature, it is easy to be exposed to the risk of fire. Thus, in previous study, we tried to monitor and notice the dangerous change of temperature of water immediately to prevent the risk of fire from plating process. However, unfortunately previous studies were not able to shut out the fundamental cause of fire since bath temperature sensor can detect air temperature when the level sensor was malfunctioned. In this paper we developed the Teflon heater which contains a built in temperature sensor and improved plating equipment system. Teflon heater is improved using Pt 100Ω sensor which can detect until 600°C . When the bath temperature sensor detects over 60°C or the Teflon heater sensor detects over 240°C they temporarily shut down the heater to control temperature. Also relay completely shuts down main power when detects instant temperature is detected over 5% of 240°C by the heater sensor to prevent teflon melting down and fire spreads. Developed plating equipment system can monitor a real time temperature in the teflon tube and bath water. Therefore we think the proposed plating equipment can eliminate the possibility of fire in plating processes fundamentally.

In this paper we developed the Teflon heater which contains a built in temperature sensor and a relay for improved plating equipment system. Teflon heater is improved by using Pt 100Ω sensor which can detect until 600°C. When the bath temperature sensor detects over 60°C or the Teflon heater sensor detects over 240°C they temporarily shut down the heater to control temperature. Also relay completely shuts down main power when detects instant temperature is detected over 5% of 240°C by the heater sensor to prevent teflon melting down and fire spreads. Developed plating equipment system can monitor a real time temperature in the teflon tube and bath water. Therefore we think the proposed plating equipment can eliminate the possibility of fire in plating processes fundamentally.

연구는 산업현장에서 발생하고 있는 중대재해를 줄이기 위해서 시행되었으며 특 히 재해 발생이 두드러지는 소규모 영세사업장을 위주로 작성하게 되었다. 소규모 현장 의 사업주는 근로자에게 개인보호구를 지급하지 않는 경우가 많아 개인보호구를 착용 하지 않고 작업장에서 작업을 하게 되고 자연스럽게 재해로 노출되고 있는 실정이다. 본 연구에서 실질적인 개인보호구 지급 방법에 대한 방안을 제시할 것이며, 기존의 산 업안전보건법상 사업주의 개인보호구 지급 기준에 대한 개정을 주장하여 재해율을 줄 이는 데 이바지하고자 한다. 근로자는 개인보호구를 스스로 구입하여 착용을 해야 하 며, 정부는 근로자의 자발적 개인보호구 구매에 대한 보상으로 퇴직공제부금을 인상하 여 주어야 하고, 사업주에게 산재보험료를 인상하여 적용, 징수하고 이 산재보험료를 통해 근로복지공단에서 개인보호구를 근로자에게 지급하는 방안을 모색해야 할 것이다.

A fire sprinkler system is very important to extinguish fire in the building. The sprinkler system initiates sprinkler discharge if the detection system identifies a developing fire and opens the pre-action valve. However, pre-action fire sprinkler systems mainly installed in the underground parking lot at the apartment complex do not properly operate at fire if the connection type of fire sprinkler systems does not properly installed and operated. This study identified the relationship between fire dispersion & damage and the connection type of water supply in the sprinkler system from many fire cases at the apartment complex in South Korea. In addition, this study also identified the water supply differences and characteristics between South Korea and foreign countries. The main purpose of this study is also to improve the water connection types in the sprinkler system that can reduce the potential failures of pre-action valve operation through electrical signal system. The study also suggests the improvement plan for water connection types in pre-action fire sprinkler system that can minimize potential failure of pre-action fire sprinkler system. The suggestions for revising the fire safe standard in South Korea includes letting the water supply pipe of sprinkler system water inlet connect to the second side of pre-action valve and the water flow device that can minimize potential failure of sprinkler system.

Job-appropriate personal protective equipment(PPE) is important for decreasing the high rates of occupational injury experienced by construction site. Objective: This analysis describes Personal protective equipment payment methods improvement by revision of occupation safety&health acts. Methodes: Data are show up during the past 9 year statistics for occupation injury cases from actual construction site in Korea construction company. Results: Most construction workers are not wearing PPE because of non-payment of PPE by employer mainly small enterprises. Conclusions: Construction site workers should be buy with job appropriate PPE themselves. Buying of PPE is essential in the near future and government should be provide appropriate compensation for self-buying action such as raise retirement deduction installment or raise of industrial accident insurance.

In the case of the fire to the exterior of the building through openings, the openings of the adjacent building are exposed to the risk of combustion expanding and factors that affect the combustion in the radiant heat and direct flame. Recent five years, fire of the adjacent building indicated that incidence of the 5,134(2.27%) among total 225,934 cases occurred The damage scale of fire expanded was lower than in a single building but casualties(5.46%) and property(25.0%) damage were higher. Therefore, this study provides to analyze the operating status for fire protection equipment of fire-preventing area in the Seoul and to apply measures to improve fire protection equipment according to narrow the distance between the building openings studied.

Recently as the testing of fire detector used the testing device for fire detector, there are something the matter in the perception function loss of fire detector, structure and form of the testing device for fire detector. The problem at oxidation of emitting smoke ashes hazardous article part and so on that checking person absorbs be. In this paper the problem or the conventional the examination equipment of fire detectors is analysed and researched. To solve these problems after the theoretical study and design and paint drawing of equipment the prototype of composite examination equipment of fire detectors was made. After compared with the conventional, part that improve of composite examination equipment of fire detectors are verified through the examination. In the future it will be useful the operation state and correct operation time of the fire detectors are measured after the research about the quality of the material and transparency of bellows cover is done.

본 연구에서는 원자력발전소 비상디젤발전기의 내진안전성을 정량적으로 평가하기 위하여 지진취약도 분석방법을 제안하고 제안한 방법을 이용하여 비상디젤발전기의 지진취약도를 평가하여 정량적인 지진위험도를 제시하였다. 기존의 비상디젤발전기뿐만 아니라 면진장치를 설치하여 지진력 저감효과를 증대시킨 비상디젤발전기에 대한 지진취약도 분석을 함께 수행하여 비상디젤발전기와 같은 대형 회전기기의 경우 면진장치를 통한 지진취약도의 변화를 살펴보았다. 최종적으로 지진취약도 결과를 이용하여 HCLPF값의 변화를 비교하여 면진에 의하여 비상디젤발전기의 취약도를 크게 개선 할 수 있는 것을 알 수 있었으며, 면진된 경우 면진장치의 파괴가 전체 거동을 지배하므로 면진장치의 성능개선이 필요한 것을 알 수 있었다.

To keep an enterprise's competitiveness on the condition of the automatic manufacturing system such as FA, FMS and CIM, all the maintenance problems should be considered seriously in not only in production and maintenance but also in related industrial productivity. This paper presents the study of equipment reliability improvement for rotary-machine vibration analysis. Based on these analyses, the maintenance management information system, and the machinery condition diagnosis technique are studied by using of the real-time diagnostic. Therefore, it is expected to improve the efficiency of business processes in the production and safety when we use this system.

The purpose of this study is to identify potentially hazardous factors which can contribute to the outbreak of food borne disease and present more practical management methods in terms of sanitary management of cooking equipment and personal hygiene. 230 Korean-style restaurants in Seoul were surveyed in the same manner on the published study-A study for the Improvement of Sanitary Condition in Korean style-restaurant in Seoul city area (I). Sanitary check-lists were developed to evaluate the sanitary status of cooking equipment and personal hygiene of employee. The sanitary condition of cooking equipment the maintenance of refrigeration, food habits and personal hygiene were assessed by the sanitary score. The sanitary condition of cooking equipment, the maintenance of refrigeration as well as food habits and personal hygiene employee was in good condition. The effective sanitation education and training for good service workers should be practice for the improvement of sanitary management of cooking equipment and personal hygiene.