As a safety device, a rupture disc are used to control pressure to minimize the explosion risk once the internal pressure of high pressure equipment exceeds a critical level. In this paper, optimization method was developed to secure optimal design of domed Rupture disks. The parameter analysis was performed through design of experiment to parameter of Rupture disk made of AISI 316.The Diameter, Thickness and Hight of Rupture disk were selected as design parameters for design parameter analysis. The results of parameter analysis revealed that the Diameter, thickness and hight were burst pressure-sensitive design parameters. Based on the valid performance factors, a regression equation to predict its performance was deducted and using the equation, an optimal design. And a sample model was fabricated, followed by burst pressure testing, after optimal design and analytical verification. In this research, it is verified that the optimal design method and the credibility of the analysis of this study is deemed very high. Furthermore, utilizing this mechanism would inspect the effect of the design parameter performance and increase the credibility and efficiency of a design.

작물을 재배하는 데 필요한 여러 가지 환경 조건 중 광은 개 화와 밀접한 연관이 있다. 본 연구는 식용화, 매리골드 화아분 화에 영향을 주는 최적의 광주기를 구명하여 완전제어형 식물 공장에서 효율적으로 재배하기 위해 진행되었다. 실험에 사 용된 광주기는 4, 8, 12, 16시간, 총 4가지로 설정하였다. 매리 골드 ‘듀란고 레드’ 종자를 우레탄 스펀지에 파종한 직후부터 광주기를 처리하였다. 화아분화는 꽃봉오리가 약 2mm 이상 일 때 화아분화가 되었다고 정의하였고, 2－3일 간격으로 조 사하였다. 생육 조사는 지상부의 생체중, 건물중, 초장, 엽면 적을 조사하였다. 최적의 광주기는 식물체의 50%가 화아분 화 된 날을 기준으로 정의하였다. 4시간 처리구에서는 식물체 가 제대로 자라지 못하며 화아도 형성되지 않았다. 8시간 이상 의 처리구에서부터 식물체가 정상적으로 생장하고 화아분화 가 이루어졌지만, 8시간 처리구는 12시간 이상의 처리구에 비 해 화아분화가 더디게 일어났다. 반면에 12시간 처리구와 16 시간 처리구는 서로 유의하지 않은 결과를 보였다. 모든 생육 조사 항목에서 16시간 광주기 처리구가 가장 높은 값을 나타 냈으나 지상부의 건물중과 엽면적을 제외한 나머지 항목에서 12시간 처리구와 유의하지 않았다. 실험 결과에 따르면, 8시간 광주기에서도 화아분화가 일어났지만, 화아형성까지의 시 간이 12시간 이상의 광주기일 때보다 더 많이 소요되었으며, 식물체의 생육 또한 12시간 이상의 광주기를 조사받은 식물 체보다 낮게 나타났다. 본 실험에서 에너지 소비량을 고려한 최적의 매리골드 ‘듀란고 레드’의 광주기는 12시간으로 판단 된다.

Engineering design involves making numerous decisions as the design process. These decisions can be broadly categorized into selection decisions and compromise decisions. The outcomes of these decisions heavily depend on the designer's intentions, highlighting the need to systematically and accurately incorporate the designer's intentions. The Analytic Hierarchy Process (AHP) is a design technique that systematically reflects the designer's intentions by hierarchically analyzing and evaluating ambiguous decision problems. Therefore, in this study, effective optimal structure designs that maximally reflect the designer's intentions were confirmed by introducing AHP (Analytic Hierarchy Process) and Neural Network into the foundational decision-making process of engineering design.

Out-of-roundness is crucial for the proper functioning of individual products or parts in a machine. Mechanical components often consist of circular elements that require precise alignment. These circular parts are used in critical areas of the machine, and the shape characteristics of each component can significantly impact overall performance. In this study, we focus on a specific specimen and use three different methods - the Diameter method, Radius method, and Three-point method - to measure its out-of-roundness. The collected data is then analyzed using one-way ANOVA to propose an effective out-of-roundness measurement technique suitable for industrial settings.

목적 : 4차 산업혁명이 진행됨에 따라 타각적 굴절검사값, 수차 및 동공크기 등을 이용하여 최적의 안경처방값 을 도출해주는 머신러닝(machine learning)을 개발하고자 하였다. 방법: 시력에 영향을 줄 수 있는 안질환 및 전신질환이 없고 안구 수술 이력이 없는 근시안(1,000안)을 대상으로 진행하였다. I-Profilerplus(Zeiss, Berlin, Germany)를 사용하여 타각적 굴절이상도(objective-refraction) 및 안구수차(ocular wavefront-aberration), 동공 크기를 측정하였고, 자각적 굴절이상도(subjective-refraction)는 Visuphor500(Zeiss, Berlin, Germany)를 사용하여 구면 굴절력(S, Diopter), 원주 굴절력(C, Diopter), 난시 축(Ax, °)을 측정하였다. 측정 후, 파이썬(Python, version 3.10)을 이용하여 머신러닝 모델 생성 및 예측 성능을 확인하였다. 결과: 자각적 굴절이상도에서 구면 굴절력에 영향을 미치는 요인은 타각적 구면 굴절력, defocus aberration, spherical aberration, trefoil aberration 순으로 높았고, 원주 굴절력에 영향을 미치는 요인은 타각적 원주 굴 절력, defocus aberration, coma aberration, trefoil aberration 순으로 높았으며, 난시 축은 타각적 난시축만 영향을 미치는 것으로 나타났다. 구면 굴절력, 원주 굴절력, 난시 축의 자각적 굴절이상도와 머신러닝 예상값은 차이가 없는 것으로 나타났다(p=0.976, 0.948, and 0.349, respectively). 결론 : 자각적 굴절이상도를 예측하는 머신러닝 모델을 생성하였고, 해당 모델의 예측된 값과 자각적 굴절이상 도와 유의한 차이가 없는 것을 통해 예측 정확도를 확인하였으며 앞으로 개인 맞춤형 처방을 위한 정확한 안경처 방값을 도출하는데 기초자료가 될 수 있을 것으로 생각된다.

A plasma torch is a kind of equipment that utilizes an electric arc to dissociate a gas and transfer an electric energy to the gas to generate very high temperature flame. KHNP-CRI has been developed the Plasma Torch Melter (PTM) to reduce radioactive waste disposal volumes and drop the radiation level of wastes. As you guess, there is required condition for proper start-up operation like current, voltage, plasma gas flow, cooling water flow, temperature in melter and so on. Thus, the optimum start-up operation condition of plasma torch will be estimated experimentally in this paper.

In order to reduce the area of the high-level radioactive waste (HLW) repository, a buffer material with high thermal conductivity is required. This is because if the thermal conductivity of the buffer material is high, the distance between the disposal tunnels and the deposition holes can be reduced. Sand, which is a natural material and has higher thermal conductivity than bentonite, is added to bentonite to develop an enhanced buffer material. For the sand-bentonite mixture, it is important which sand to use and how much to add because an enhanced buffer material should satisfy both hydraulic (H) and mechanical (M) performance criteria while improving thermal conductivity (T). In this study, we would like to show what type of sand and how much sand should be added to develop an enhanced buffer material by adding sand to Gyeongju bentonite, a representative bentonite in Korea. For this purpose, the thermal conductivity, hydraulic conductivity, and swelling pressure of the sand-Gyeongju bentonite mixture according to the sand addition rate were measured. It is more efficient to use silica sand with smaller particles than Jumunjin sand which is a representative sand in Korea as an additive for an enhanced buffer material than using the Jumunjin sand. In order for the sand-Gyeongju bentonite buffer material to satisfy both the hydraulic and mechanical performance criteria as a buffer material while increasing the thermal conductivity, it is judged that the optimum dry density is 1.7 g/cm3 at least and the optimum sand addition rate is 10% at most.

Dongchimi is one of the most representative types of watery kimchi in Korea. Although the scope of application of dongchimi has been expanded, research on the quality of dongchimi is insufficient compared to that of baechu kimchi. This study aimed to find the optimal manufacturing condition of high-acidity dongchimi and investigate the effects of potassium citrate (P) and sugar (S) on quality. Different dongchimi samples (Control, S, P) were prepared and stored at 15oC for 15 days. Among the various sugars, sucrose made the highest acidity of dongchimi. When potassium citrate was added as a pH buffer, the acidity was 2.2 times higher than the control group. In the PS group, where sucrose and potassium citrate were added, the acidity and organic acid content were 3-fold and 3.7-fold higher, respectively, than those in the control group. As a result of the analysis of the free sugar content, the metabolism of lactic acid bacteria was expected to be relatively more activated in the PS group. Therefore, this study could be utilized in the dongchimi manufacturing industry or as primary data for other dongchimi research.

In this study, a new type of composite material combined with carbonyl iron, a relatively strong ferromagnetic material, was prepared to overcome the current application limitations of Prussian blue, which is effective in removing radioactive cesium. The surface of the prepared composite was analyzed using SEM and XRD, and it was confirmed that nano-sized Prussian Blue was synthesized on the particle surface. In order to evaluate the cesium removal ability, 0.2 g of the composite prepared for raw cesium aquatic solution at a concentration of 5 μg was added and reacted, resulting in a cesium removal rate of 99.5 %. The complex follows Langmuir’s adsorption model and has a maximum adsorption amount (qe) of 79.3 mg/g. The Central Composite Design (CCD) of the Response Surface Method (RSM) was used to derive the optimal application conditions of the prepared composite. The optimal application conditions achieved using Response optimization appeared at a stirring speed of pH 7, 17.6 RPM. The composite manufactured through this research is a material that overcomes the Prussian Blue limit in powder form and is considered to be excellent economically and environmentally when applied to a cesium removal site.

Concentration of nitrogen, one of the major elements, and ratio of two nitrogen forms (NH4 + and NO3 –) in the nutrient solution affect the quality and food safety of fresh vegetable produce. This study was conducted to find an appropriate strength and NH4 +:NO3 – ratio of a nutrient solution for growth and development of a Romaine lettuce (Lactuca sativa L. var. longiflora) ‘Caesar Green’, a representative leafy vegetable, grown in a home hydroponic system. In the first experiment, plants were grown using three types of nutrient solution: A commercial nutrient solution (Peters) and two strengths (GNU1 and GNU2) of a multipurpose nutrient solution (GNU solution) developed in a Gyeongsang National University lab. Plants grown with the GNU1 and GNU2 had greater shoot length, leaf length and width, and biomass yield than Peters. On the other hand, the root hairs of plants grown with Peters were short and dark in color. Tissue NH4 + content in the Peters was higher than that of the GNU1 and GNU2. The higher contents of NH4 + in this solution may have caused ammonium toxicity. In the second experiment, eight treatment solutions, combining GNU1 and GNU2 solutions with four ratios of NO3 –:NH4 + named as 1, 2, 3 and 4 were used. Both experiments showed more growth in the GNU2 group, which had a relatively low ionic strength of the nutrient solution. The growth of Romaine lettuce showed the greatest fresh weight along with low tissue NO3 – content in the GNU2-2. This was more advantageous in terms of food safety in that it suppressed the accumulation of surplus NO3 – in tissues due to the low ionic strength of the GNU2 subgroup. In addition, this is preferable in that it can reduce the absolute amount of the input of inorganic nutrients to the nutrient solution.

Traffic accidents that occur while driving a car are inevitable, and the characteristics of the body repair field are that each vehicle accident has the same damage and no same repair conditions. Therefore, it is difficult to acquire know-how in vehicle body repair simply by theoretical method of textbook, and the repair method must be changed as new materials and new technologies are applied to it. In particular, roof panels are not frequently damaged by traffic accidents, but they are damaged by falling objects from the roof of a building or the opposite lane, resulting in roof bending and vehicle repair using dent repair to minimize VOC and reduce costs. In this study, the optimal maintenance method is proposed by analyzing the time, cost, and waste generation according to the work method when the degree of damage is large and replacement is required

방충설비는 선박의 접안 및 양하역 과정에서 선박의 충격력을 흡수하여 선박과 접안시설을 모두 보호하는 매우 중 요한 역할을 수행한다. 하지만 이에 대한 최근 연구 및 설계 최적화의 노력이 매우 부족해 보인다. 이에 본 논문은 국내 항만 설계기준에서 제시하고 있는 방충재 설계에 사용되는 선박 접안에너지 산정식을 개선, 보완하기 위하여 연구를 수행하였다. 접 안에너지 산정과정에서 선박 및 접안시설의 조건을 고려하기 위하여 적용되는 영향계수의 변화에 따른 영향을 분석하였으며, 이 과정에서 국내외 설계코드에서 제시하고 있는 산정방법과 최신 선박제원, 국내 설계결과가 활용되었다. 분석에는 최신 선박 의 표준제원과 국내에서 실시된 실제 설계결과가 적용되었다. 그 결과, 국내 항만 설계기준에서 제시하고 있는 영향계수 결정방 법은 선박과 접안시설의 조건을 최적으로 반영하기에는 부족하며, 접안에너지가 20%이상 크게 산정되어 방충재 선정과정에서 과다 설계가 야기될 수 있는 것으로 판단되었다. 이에, 국내 항만 설계기준에서 제시하고 있는 영향계수를 선박 및 접안여건을 고려하여 설계할 수 있도록 최적화된 방법을 제시하였다.

Considering the features of body repair for automotive body where same damage and repair conditions does not exist in car accident, it is essential to acquire know-how and continuously approach new materials and new technologies on the site of maintenance where the theoretical instruction of textbook cannot react accurately minute by minute. Especially, in case of car repair from unexpected accidents such as body repair or dent repair, it is difficult to satisfy vehicle owners despite their request. Accordingly, this study researched the better maintenance technology to restore to its original state with more improved technology as vehicle owners wish. This study made time to repair reduced by 98% and the cost reduced by 79.6% through the accurate diagnostic technique before repair and maintenance technologies of body crash analysis applying property of high-speed tensile. It also obtains intangible effects including prevention of environmental pollution and maximization of vehicle owners satisfaction.

Pleurotus species are the most consumed and cultivated mushrooms in Korea. Although oyster mushrooms (P. ostreatus) can be cultivated automatically, their storability is slightly lower than that of king oyster mushrooms (P. eryngii) and winter mushrooms (Flammulina velutipes); therefore, the export proportion of oyster mushrooms is very low. Since Korean mushrooms are highly preferred across Southeast Asian, the export of oyster mushrooms in the form of complete substrates is expected to be more promising than that of fresh mushroom. Here, 1 and 2.5 kg complete substrates of P. ostreatus ‘Soltari’ and P. sajor-caju ‘Sambok’ were prepared and stored at different temperature from 0 to 15°C for 10 days. Thereafter, the formation of fruiting bodies was induced. Since the 2.5 kg complete substrates required 70 days of incubation, their mycelia were at an advanced age and their fruiting bodies did not grown normally. When 70%-incubated complete substrates were stored at 5–10°C, the growth was faster and more uniform and stable fruiting bodies were formed. Export test of complete substrates to Vietnam using distribution containers set at 0°C and 15°C revealed that the growth period was shortened by 1–2 days when the distribution containers were set at 15°C and the yield of ‘Soltari’ increased by approximately 10%. In addition, even though the yield of ‘Sambok’ was similar between treatments at 0°C and 15°C, the quality of fruiting bodies from 15°C-distributed complete substrates was much better than that of those from 0°C-distributed substrates.

레일장대화는 무도상교량의 소음, 진동, 충격 등의 문제점을 해결할 수 있는 경제적인 방안 중 하나이며, 최근 연동식 침목고정장치 를 이용한 SSF 공법이 개발된 바 있다. 이 연구에서는 연동식 침목고정장치 적용 시 레일 높이 조정 및 열차 통과 시의 충격 흡수를 목 적으로 교량침목 하부에 삽입되는 침목패드의 최적 연직강성을 결정하는 과정을 제시하였다. 침목패드의 최적 연직강성 결정을 위하 여 관련 기존 기준을 검토하였으며, 유연다물체동적해석을 통하여 침목패드의 연직강성 변화에 따른 주행안전성, 승차감 및 궤도의 안전성에 대한 지표들과 교량 응답 변화를 검토하였다. 유연다물체동적해석은 상용프로그램인 ABAQUS와 VI-Rail을 이용하여 수행 하였다. 수치해석은 30m 상로판형교에 대한 교량모델을 이용하여 수행하였으며, 침목패드의 연직강성이 7.5kN/mm ~ 240kN/mm로 변화할 때 ITX 새마을, KTX 및 화차 통과 시의 응답을 산정하였다. 수치해석에 적용된 궤도구성품 조건에서 침목패드의 최적 강성은 100kN/mm로 산정되었다.

PURPOSES : In this study, a driving simulation testing equipment was developed to derive the optimal longitudinal tinting that can reduce the lateral vibration of the vehicle. Various types of longitudinal textures and tires were evaluated through simulation testing with the equipment. Based on the results, 3×3×16mm tinning as the optimal longitudinal texture was selected among 8 textures. METHODS : Based on the literature review, the causes of lateral vibration were analyzed, and parts and types for testing equipment development were reviewed. Driving simulation with testing equipment was conducted considering various textures and tires. To verify the test results, finite element analysis was performed under the similar conditions. And field test for two textures was conducted to find the optimal longitudinal texture. RESULTS : Based on the literature review, driving simulation test, finite element analysis and field test, longitudinal texture of 3×3×16mm is show the better performance compared to 7 textures. CONCLUSIONS : 3×3×16mm as longitudinal tinning for fresh concrete is show less lateral vibration than 3×3×12mm.