Hydrogen infrastructure, for instance, such as hydrogen stations, supply chain network, is important in society of hydrogen economy. Special alloy are frequently used to prevent the hydrogen embrittlement in hydrogen vehicles, semiconductor factories and so on. Because special alloy including Monel material has high strength and high hardness, it is known as the hard-to-cut or roll material. This paper aims to investigate the characteristics and safety on bearing and shaft, which consist of key parts of rolling unit, through structural analysis. As the results, it showed that the bearing was weaker than shaft. Further the bearing was safe up to 20.4 ton, which was about 2 times of maximum of roller reaction force in case of considering as static load. However, the bearing was safe up to 10.2 ton in case of considering as repeated load.

The radioactive Sr-90, which is formed from beta decay, is well known as one of the most commonly detected nuclides in radioactive waste. In 2015, it was reported that Sr-90 was observed in some soil and metal wastes among the 516 drums of radioactive waste transferred from the decommissioning site of the Korea Research Reactor (in Seoul) to the disposal site (in Gyeongju). Decontamination and sequestration of radionuclides, including Sr, from nuclear waste is important because they are hazardous and harmful to the ecological environment. Immobilization of these nuclides using a zeolite framework is suitable and simple method that has been widely studied. Therefore, it is still necessary to continuously explore the thermal stability of various zeolites and environmental changes around adsorbed cations in zeolite pore for effective immobilization of these radionuclides. In this study, we observed the thermal stability in fully Sr-exchanged natrolite (Sr-NAT), one of small-pore zeolite, from room temperature to 350°C using the in-situ synchrotron X-ray powder diffraction and thermogravimetric (TGA) analysis. In addition, we investigated the structural changes in Sr-NAT during temperature increase by Rietveld analysis. Sr-NAT exhibited apparent zero thermal expansions (ZTE) with the thermal expansion coefficients of -3(1) × 10-6 at the initial stage of increasing the temperature due to dehydration process. In the section from 250°C to 300°C, a phenomenon like negative thermal expansion (NTE) occurs in which the unit cell volume of Sr-NAT decreases despite the increase in temperature. Sr-NAT maintained well its crystallinity up to 350°C, and it became amorphous at 350°C. In this study, we provide a fundamental understanding of the structural changes and thermal stability mechanism of Sr-exchaged zeolite natrolite with increasing temperature.

Uranium-235, used in nuclear power generation, produces a lot of radioactive waste. Among radioactive waste nuclides, I-129 is problematic due to its long half-life (1.57×107 y) with high mobility in the environment. It should be captured and immobilized into a geological disposal environment through a stable waste form. In this study, various additives including Al, Bi, Pb, V, Mo and W were added to silver tellurite glass to prepare a matrix for immobilizing iodine, and its thermal and leaching properties were evaluated. To prepare glass, the glass precursor mixture was placed in alumina crucibles and heated at 800°C for 1 h. Except for aluminum, there was no significant loss of constituent elements. The loading of iodine in the matrix was approximately 11-15% by weigh, excluding oxygen. The normalized releases of all the elements obtained by PCT-A were below the order of 10-1 g/m2, which satisfies US regulation (2 g/m2). Differential scanning calorimetry was performed to evaluate the thermal properties of the glass samples. The glass transition temperature (Tg) increased by adding such as V2O5, MoO3, or WO3. The similar relative electrostatic field values of V2O5, MoO3, and WO3 could provide sufficient electro static field to the TeO2 interacting with the non-bridging oxygen forming Te-O-M (M = V, Mo, W) links. The addition of MoO3 or WO3 in the silver tellurite glass system increased glass transition temperature (Tg) and crystallization temperature (Tc) while maintaining the glass stability.

Recently, the deep geological disposal system isolating a spent nuclear fuel (SNF) is considered a disposal method of high-level radioactive waste for the safety of humans or the natural environment. The one of important requirements for maintaining the thermal stability of these systems is that the temperature of the buffer does not exceed 100°C even though the decay heat is emitted from highlevel radioactive wastes loaded in the disposal container. In 2007, a deep geological disposal system based on the Swedish disposal concept was developed for the SNF in Korea. To respond to the development process, the thermal stability of the deep geological disposal system developed for the disposal of domestic pressurized light water reactor (PWR) SNFs with discharged burn-up of 55 GWD/MTU was evaluated in 2019. The thing is that the recent fuel activity is pursuing to operate further high burn-up fuel conditions, and it leads to emergency core cooling system (ECCS) revision for extending the license for up to 60 or more than 60 GWD/MTU in the world. In this regard, this study evaluates numerically the thermal stability of the deep geological disposal system for the high burn-up PWR SNF having large decay heat compared to previous conditions for two different length disposal containers classified according to the length of PWR SNFs discharged from domestic nuclear power plants. A finite element analysis using a computational program was used to evaluate the thermal design requirements. Results show that both types of disposal containers would increase the temperature which reduces or fails to meet the safety margin of the disposal system. This study suggests that the design of the previous disposal system is needed to be further developed for the high burn-up PWR SNF which would be used in future nuclear power plant systems.

PURPOSES : In this study, an existing speed-controlled Marshall stability tester was systemized as an Internet of Things(IoT) system. The Marshall stability test data were transmitted to the cloud in real-time, and an IoT optional-controlled board capable of additional load and displacement control was proposed. METHODS : The IoT systemization was built based on an improvement of an IoT height measuring system, the re-verification of standard samples for comparative analysis, and the development of a wireless IG-IoT board. The developed wireless Induk-GeoTS(IG)-IoT board was compared with existing commercial data logger using displacement- and load- calibration equipment. After the conformity of the developed wireless IoT board was established, a urethane standard sample was reproduced and verified using the recipe presented in a previous study to conduct a round-robin test. In addition, the adequacy of the speed, load, and displacement control tests for the optional-controlled characteristics was verified. the round-robin test for the Marshall stability and deformation strength and the comparative test of indirect tensile strength with the existing Marshall tester were performed using the re-verified standard sample. RESULTS : The improved two-point IoT height measurement system reduced the average relative error by 2.11% relative to the one-point measurement. From the re-verification results of the regenerated urethane standard sample, it was suitable with relative error of 3.65% in the loading elastic modulus and 4.07% in the unloading elastic modulus, compared to the existing standard sample. From the comparative analysis of the developed wireless IG-IoT board and existing commercial data logger, it was confirmed that the wireless IoT board could be reliably used, based on the average relative error of the wireless IoT board, 0.64% and that of the data logger, 3.79% in terms of the displacement(flow value) and an average relative error of 0.78% for the wireless IoT board and 0.79% for the data logger in terms of the load(stability). By analyzing the optional-controlled characteristics, it was found that the Marshall stability speed control conditions were satisfied based on the error results, with an average relative value of 2.96% under deformation strength test condition of 30mm/min, 3.23% under the indirect tensile strength test condition of 50mm/min, and 2.6% under the Marshall stability test condition of 50.8mm/min. It was also found that proper control characteristics were obtained, with an average relative error of 0.72% within the experimental load range in the load control conditions, and an average relative error of 2.4% in the experimental displacement range in the displacement control conditions. The results from the round-robin Marshall stability and deformation strength testing to verify the applicability of the IoT optional-controlled board show that the data were reliable based on the 3σ quality control method. In addition, by comparing the results of the indirect tensile strength tests, the usability of the wireless IG-IoT board was verified, with an average relative error of 0.96%. CONCLUSIONS : The IoT height measuring system was improved, and a wireless IG-IoT board that can transmit test data to a cloud platform was developed. The usability of the developed wireless IoT board was verified by round-robin testing using a re-verified urethane specimen. The IG-IoT optional-controlled board extends the verified wireless IG-IoT board, it was developed and validated for not only the existing speed control, but also for load, and displacement control.

The purpose of this study was to breed a variety of stable productivity and high storage characteristics of white Hypsizygus marmoreus, which has high demand at domestic and global market due to a low bitter taste and the preference for white species. Accordingly, ‘Baekmaru’ was bred by hybridizing brown and white cap color species and backcrossing with white species. The ‘Baekmaru’ variety was bred by crossbreeding the brown and white species and backcrossing the white species. Through repeated cultivation of ‘Baekmaru’, a variety with a low contamination rate was selected when culturing the spawn for stable cultivation. As a results of demonstration test, the yield of ‘Baekmaru’ was 14% higher than that of the commercial variety. In addition, among the fruiting body characteristics of ‘Baekmaru’, diameter and thickness of the pileus were 16.43±15.27mm and 6.46±0.58mm, which were slightly higher than the commercial variety, and the hardness was 2.69±0.89N for the pileus and 3.09±0.89N for the stipe. The shelf life showed less change in thickness and color of pileus compared to commercial variety. The hardness of pileus of 'Baekmaru' was maintained in the range of 3.5 to 4.0N in the 4oC and 4oC and 20oC mixed treatment until 30 days of storage, and was higher than that of the commercial variety. Therefore, it was suggested to be excellent in storability.

유선 및 도선 중 선박길이 12미터 미만인 소형선박은 선박안전법에 따른 복원성 기준 적용이 면제되며, 유선 및 도선 사업법에 따라 승객 및 선원이 탑승 가능한 면적을 고려하여 승선정원을 정하고 있다. 이러한 유선 및 도선 중에서는 건조 이후 차양의 설치 등 복 원성에 영향을 미치는 상부 구조물을 설치하는 사례도 적지 않다. 이에 본 연구에서는 상부 구조물을 설치한 도선에서 실제 발생한 전복 사고의 사례를 바탕으로 해당 도선의 복원성을 추정하여 사고 원인을 분석하고자 하였다. 분석 결과, 승선정원을 초과한 상태에서 승객들 이 동시에 하선하고자 기립하여 복원성이 악화된 것으로 나타났으나, 해당 도선이 승선정원을 준수하더라도 한쪽 현의 승객들이 기립하 면 횡경사에 의한 전복의 가능성이 존재하였다. 따라서, 보다 안전한 유선 및 도선사업을 위하여 선박길이 12미터 미만의 유선 및 도선에 대하여 건조 및 개조 시 실선 복원성 시험에 의한 승선정원 산출, 승선정원의 총중량 한곗값 제시 등을 개선방안으로 제시하였다.

본 연구의 목적은 좌우 방향의 회전 후 직립자세 시 압력중심과 근전도 분석을 토대로 회전선호 도가 신체 안정성에 미치는 영향을 알아보고자 하였다. 연구의 대상은 오른쪽 손과 발의 편측선호도가 높 은 대상자 16명으로 3가지 회전방향 조건(QS: 직립자세, LT: 왼쪽 10바퀴, RT: 오른쪽 10바퀴)을 수행하 였다. 회전 후 직립자세 시 안정성을 평가하기 위하여 압력측정판과 근전도를 이용하여 결과를 도출하여 분석하였다. 연구결과로 모든 압력중심 변인은 QS보다 LT, RT가 크게 나타났지만, 회전방향에 따른 차이 는 보이지 않았다. 근전도 결과는 좌우 비복근에서 회전방향에 따라 RT가 QS보다 근활성도가 크게 발생 되었다. 결론적으로 대상자가 모두 오른쪽 측면선호도가 높았지만 압력중심에서는 회전선호도의 영향이 없 었고, 비복근에서는 회전선호도의 영향이 나타났다.

This paper is about structural, and vibration analysis for the development of Index chucks Structural and vibration analyses were performed using the ANSYS Mechanical program to evaluate the Index chuck's structural stability and vibration characteristics. As a analysis result, when the maximum load of 500N was applied to the Index chuck, the safety factors were 2.06, 2.09, and 2.60, respectively, when the thickness was 5mm, and the outer diameters were 70mm, 90mm, and 120mm, respectively. Structurally safe results were obtained. In addition, under load conditions of 300 N or less, structural safety was confirmed if the thickness is 3mm or more.

The present study investigated effects of microbial additives and silo density on chemical compositions, fermentation indices, and aerobic stability of whole crop rice (WCR) silage. The WCR (“Youngwoo”) was harvested at 49.7% dry matter (DM), and ensiled into 500 kg bale silo with two different compaction pressures at 430 kgf (kilogram-force)/cm2 (LOW) and 760 kgf/cm2 (HIGH) densities. All WCR forage were applied distilled water (CON) or mixed inoculants (Lactobacillus brevis 5M2 and Lactobacillus buchneri 6M1) with 1:1 ratio at 1x105 colony forming unit/g (INO). The concentrations of DM, crude protein, ether extract, crude ash, neutral detergent fiber, and acid detergent fiber of whole crop rice before ensiling were 49.7, 9.59, 2.85, 6.74, 39.7, and 21.9%, respectively. Microbial additives and silo density did not affect the chemical compositions of WCR silage (p>0.05). The INO silages had lower lactate (p<0.001), but higher propionate (p<0.001). The LOW silages had higher lactate (p=0.004). The INO silages had higher yeast count (p<0.001) and aerobic stability (p<0.001). However, microbial counts and aerobic stability were not affected by silo density. Therefore, this study concluded that fermentation quality of WCR silage improved by microbial additives, but no effects by silo density.

본 연구는 기능성 물질인 알로에를 종류별로 첨가함에 따라 유화소시지의 이화학적 특성과 저장성, 그리고 관능성에 미치는 영향을 조사하기 위해 수행되었다. 알로에 베라(AV구)와 알로에 사포나리아(AS구)는 각 3%씩 첨가하였으며, 모든 처리구들은 냉장온도 4±1℃에서 4주간 저장하면서 주 1회 간격으로 실험이 진행되었다. pH는 AV구와 AS구가 대조구보다 유의적(p<0.05)으로 낮았고, 저장기간의 경과함에 따라 대조구 및 모든 처리구는 증가하였다. 보수성에서 AS구는 대조구와 AV구보다 유의적(p<0.05)으로 높은 값을 나타냈으며, 저장기간의 경과함에 따라 대조구 및 모든 처리구는 유의적(p<0.05)으로 감소하였다. 적색도는 AS구가 대조구 및 AV구 보다 낮은 값을 나타내었고, 황색도는 AS구가 대조구, AV구보다 높은 값을 나타내었다. 전단가는 AS구가 대조구보다 낮은 값을 나타냈으며, AV구와는 유의적인 차이가 없었다. 지방 산패도에서 AS구는 유의적 (p<0.05)으로 가장 낮은 값을 나타내었고, 관능 평가의 색은 AV구가 가장 높은 값을 나타냈으며, 선호도는 AV구가 대조구보다 높은 값을 나타냈고 AS구와는 유의적인 차이가 없었다. 이는 알로에 사포나리아의 첨가가 높은 보수성, 알로에 베라 첨가보다 낮은 지방산패도, 유사한 관능성을 나타내 기능성 소시지의 개발에 충분한 경쟁력을 가지고 있으며 향후 알로에 사포나리아를 첨가한 육제품의 일반화 및 대량생산 체계의 확립에 긍정적인 영향을 준다고 판단된다.