For the regeneration of diesel particulate filters (DPF) using non-thermal plasma (NTP), both cost-effectiveness and regeneration efficiency should be raised. This study compared and contrasted the physicochemical characteristics of carbon black and engine particulate matter (PM). After carbon black was put into the DPF, an experimental setup for the oxidation of PM using NTP was created. The findings showed that carbon black and PM samples had comparable oxidation traits, micronanostructures, and C/O elemental ratios. O3, the main active species in NTP, was susceptible to heat breakdown, and the rate of decomposition of O3 increases with increasing temperature. The removal effectiveness of carbon black first improved and subsequently declined with an increase in the NTP injection flow rate during offline DPF regeneration using NTP at room temperature. A relatively high carbon black removal efficiency of 85.1% was achieved at an NTP injection flow rate of 30 L/min.

When a fire breaks out in a distribution center, it causes a lot of damage. And the most casualties are caused by Fire accidents. Therefore, training for fire prevention should be mandatory at the distribution center. Also, the contents of education should be different in room temperature warehouses and low temperature warehouses. Fire education in low-temperature warehouses should be more emphasized. This is because many fires occur in low-temperature warehouses. In this study, a study was conducted to determine the important order of training hours and contents for fire prevention education according to the type of distribution center. The importance of time and content for safety education in all types of warehouses did not differ significantly. It was first decided that safety prevention training should be conducted periodically in all types of warehouses

For the commercialization of hydrogen energy, a technology enabling safe storage and the transport of large amounts of hydrogen is needed. Porous materials are attracting attention as hydrogen storage material; however, their gravimetric hydrogen storage capacity (GHSC) at room temperature (RT) is insufficient for actual use. In an effort to overcome this limitation, we present a N-doped microporous carbon that contains large proportion of micropores with diameters below 1 nm and small amounts of N elements imparted by the nitrogen plasma treatment. The N-doped microporous carbon exhibits the highest total GHSC (1.59 wt%) at RT, and we compare the hydrogen storage capacities of our sample with those of metal alloys, showing their advantages and disadvantages as hydrogen storage materials.

This study was carried out to determine the sprouting period of early and mid-season varieties, which includes ‘Atlantic’, ‘Chubaek’, and ‘Superior’, during the summer storage period in a semi-underground warehouse without cooling system. And also it was investigated the effect of chlorpropham [Propan-2-yl N-(3-chlorophenyl)carbamate, CIPC] treatment on the sprouting inhibition for the varieties. This study was conducted to figure out a sprout inhibitory effect when CIPC was applied to 1kg of the potato tubers at concentrations of 10 mg and 20 mg which are lower than the treatment concentrations of ca 30 mg prescribed by the positive list system (PLS). The internal temperature of the warehouse used in this experiment was lowered by 5°C or more than the outside temperature. The difference between the lowest and highest temperature during the experiment throughout the day was 5°C. It showed the effect of reducing to 1/2 of the difference in outdoor temperature. As for the sprouting of potatoes, the extremely early variety ‘Chubaek’ sprouts appeared at the 6th week of storage of control and it was the fastest sprouting potato among the control groups of the varieties. Sprouting began to appear in the Superior at the 6th week of storage, while the ‘Atlantic’ sprouted at the 8th week of storage. The appearance of sprouts was suppressed in all treatment groups of ‘Atlantic’ and ‘Superior’ varieties in CIPC treatments. Sprouts were observed in all treatment groups of ‘Chubaek’ after the 7th week, but the elongations of the sprouts in tubers were completely inhibited until the 8th week of storage. ‘Atlantic’ and ‘Superior’ seemed to have a sprouting inhibitory effect even with a low CIPC concentration of 10 mg·kg-1, with the exception of extremely early variety ‘Chubaek’ that breaks out of the dormancy quickly. Although weight loss occurred continuously during storage, it was minor loss of 0.7-1.6%. There was no consistent trend for changes of the loss in the varieties and CIPC treatments. Most common pathological disorder was the dry rot during the experiment, but only few were affected. The use of the tubers treated at 18°C and 90% RH for 10 days and the rack of refrigeration system which lead to lack of convection seemed to have suppressed the spread of pathogens.

The preparation and exfoliation of graphite oxide at low temperatures (near room temperature) to produce exfoliated graphite (EG) instead of rapid heating to a high temperature (conventional process) are reviewed. The exfoliation by microwave irradiation, electrochemical exfoliation and surfactant-assisted exfoliation of graphite are also included because these techniques can be applied under ambient atmosphere, although last two techniques were mainly applied for thinning the graphite flakes to obtain “graphene” flakes. The applications of the resultant exfoliated graphite (EG) for oil/water separation, adsorptive removal of the environment pollutants and microwave shielding are shortly reviewed.

본 연구에서는 참외과실의 수확후 식용왁스코팅처리가 과실품질 및 과골 갈변에 미치는 대사체의 변화를 분석하였다. 코코넛 오일과 밀랍 (9:1 w/w) 처리를 참외 과실표면에 코팅 후 실온 저장 7일후에 과실 품질, 에틸렌 발생량 및 호흡량을 조사하였다. 그 결과, 참외의 경도와 골갈변도는 식용코팅처리된 과실과 무처리군 사이에 유의한 차이는 없었다. 하지만, 과피색의 명도(L*), 순도(a*), 및 색상각(hue angle)은 식용왁스처리군이 무처리군에 비해 유의한 차이가 있었다. 이는 호흡량 및 에틸렌 발생량이 식용왁스처리에 의해 유의하게 낮아져 과피색이 유지된 것으로 생각된다. 식용왁스 처리에 의한 참외의 대사체 변화를 분석한 결과, gamma-aminobutyric acid, aspartate 그리고 myo-inositol 대사가 가장 유의적인 차이를 나타났으며, 특히 삼투보호제 역할을 하는 alanine, 가바(GABA)성분이 식용왁스코팅에 의해 증가하였다. 따라서, 식용왁스코팅처리는 호흡과 에틸렌 발생의 억제, 수분 스트레스 경감 등을 통해 참외의 선도 유지를 유도한 것으로 판단되며, 참외 과피색 변화 억제 등 상품성 향상에 활용될 수 있을 것으로 보인다.

본 연구에서는 국내에서 소비도 및 인지도가 높은 식용 버섯인 큰느타리(Pleurotus eryngii), 느타리(Pleurotus ostreatus), 표고(Lentinula edodes), 팽이(Flammulina velutipes)의 열풍건조 및 로스팅 시료를 대상으로 상온 (20-25 ̊C) 및 저온저장(4 ̊C) 3개월 후의 시료와 저장 전의 시료와의 항산화능, 아질산염 소거능 및 베타글루칸 성분 변화를 알아보기 위하여 실험을 수행하였다. DPPH 라디칼 소거능은 큰느타리와 표고의 열풍건조 시료를 제외하고 다른 열풍건조 및 로스팅 시료의 상온저장 처리가 가장 낮은 소거능을 나타냈다. 총 폴리페놀 함량은 큰느타리와 표고 열풍건조 시료를 제외하고 상온저장 시 함량치가 가장 낮았으며, 모든 식용 버섯류의 로스팅 시료에서 저장 전에 비하여 상온 및 저온저장 시에 함량이 감소하였다. 철환원 항산화능은 표고의 로스팅 시료를 제외하고 다른 버섯류의 열풍건조 및 로스팅 시료에서 저장 전에 비하여 상온 및 저온저장 시료에서 높아지는 경향이었으며, 환원력은 열풍건조 및 로스팅 시료의 상온 및 저온저장 시에 저장 전에 비하여 증가하는 경향을 나타냈다. 베타글루칸 함량의 경우, 열풍건조 및 로스팅 시료의 상온 저장된 시료에서 가장 낮은 함량치를 보였다. 본 연구의 결과는 식용버섯 가공원료의 상온 또는 저온저장 시에 버섯에 함유되어 있는 항산화, 베타글루칸 등과 같은 유용한 생리활성 성분의 변화 정도를 예측할 수 있는 기초적 자료로서 그 활용도가 높으리라 기대된다.

소형선박 기관실 내 화재 시 개구부 유동 및 온도에 대해 FDS(Fire Dynamics Simulator)를 이용하여 화재시뮬레이션을 수행하였다. 열방출률이 10 kW 급인 경유(Diesel) 화재를 대상으로 하였고, 천장 통풍통의 위치, 측면 개구부 유·무 및 크기에 대한 영향을 파악하였다. 측면 개구부의 유·무 및 크기는 연기 거동 뿐 아니라 개구부를 통한 질량 유량 및 온도에 지대한 영향을 미쳤다. 측면 개구부가 미설치되거나 크기가 작은 경우 연기층이 기관실 내 바닥까지 도달하였고, 측면 개구부의 크기가 증가함에 따라 개구부를 통한 질량 유량이 증가하고 온도는 감소하는 경향이 나타났다. 반면, 천장 통풍통의 위치가 연기 거동, 개구부를 통한 질량 유량 및 온도에 미치는 영향은 측면 개구부 크기에 비해 상대적으로 미미한 것으로 관찰되었다. 따라서 소형선박의 기관실 내 화재 시 안전성 향상을 위해서는 천장 통풍통 위치보다 측면 개구부의 크기가 더 중요한 설계 인자인 것으로 판단된다.

곤약의 제조 공정은 크게 분말제조과정, 응고과정 및 제 성과정으로 나눌 수 있었다. 곤약의 일반세균수는 응고제와 침지액의 농도가 높아질수록 뚜렷한 감소 경향을 나타낸 반면 용수의 온도는 유의미한 영향을 미치지 못하였다. 곤약의 저장성 실험에서 응고제[Ca(OH)2] 농도를 1.0%로 유지할 경우 인장강도는 10개월까지 큰 변화 없이 유지되는 것으로 나타났으나 0.8% 이하로 유지할 경우 급격한 감소를 나타내는 경향을 보였다. 일반세균수도 인장강도의 변화와 유사한 패턴을 보였다. 응고제 농도를 1.0%로 고정한 후 침지액에 의한 영향을 확인한 결과 시험된 모든 침지액 농도(4×10-3-1.2×10-2 N)에서 인장강도와 일반세균수 모두 저장 10개월까지 큰 변화없이 유지되는 것으로 나타났다. 이는 곤약의 저장시 응고제의 농도가 결정적 영향을 미치는 것을 의미하는 것으로 상온에서 응고제의 농도를 1.0% 이상 유지할 경우 침지액의 농도에 상관없이 상온에서 10개월 동안 물성을 유지할 수 있다는 것을 의미한다.

Odor emitted from food waste is commonly known as a severe problem, and needs to be controlled to minimize public complaints against food waste collection systems. In this study, ozone oxidation with manganese oxide catalyst, which is known to effectively treat odorous substances at room temperature, was applied to remove acetaldehyde and hydrogen sulfide, the model odorous compounds from food waste. In addition, the effect of relative humidity (RH) on the ozone/catalyst oxidation was tested at 40%, 60%, and 80%. When the catalyst was not applied, the removal of acetaldehyde was not observed with the ozone oxidation alone. In addition, hydrogen sulfide was slowly oxidized without a clear relationship under RH conditions. Meanwhile, the ozone oxidation rates for acetaldehyde and hydrogen sulfide substantially increased in the presence of the catalyst, but the removal efficiencies for both compounds decreased with increasing RH. Under the high RH conditions, active oxygen radicals, which were generated by ozone decomposition on the surface of the catalyst, were presumably absorbed and reacted with moisture, and the decomposition rate of the odorous compounds might be limited. Consequently, when the ozone oxidation device with a catalyst was applied to control odor from food waste, RH must be taken into account to determine the removal rates of target compounds. Moreover, its effect on the system performance must be carefully evaluated.

To fabricate the 5182 aluminum-polymer sandwich panels, the strength of 5182 aluminum panels, which are the skin sheets that constitutes the sandwich composite panels, is changed according to the degree of heat treatment after rolling, and the characteristics of sandwich panel are also changed. In addition, in the stress-strain curves of the sandwich panel, the serration behavior observed in the 5182 aluminum alloy sheet is also observed. This serration behavior causes surface roughness during sheet forming, which is a serious problem in application to automotive body sheet. In this study, the tensile properties of the 5182 aluminum sandwich panels at room and elevated temperature were carefully investigated by tensile test. It can be found that when the aluminum surface sheets having insufficient heat treatment time is applied, the serration behavior does not completely disappear from the temperature of the room temperature to 160℃.

We assessed the growth characteristics of Auricularia polytricha ‘Geoni’ cultivated in a simple greenhouse constructed of polyethylene (PE) without air conditioning (high temperature) and in an air conditioned mushroomhouse. The successful cultivation of A. polytricha ‘Geoni’ at high temperatures can reduce energy and facility investment costs. The comparison of growth characteristics of the fungi grown under the different temperature conditions revealed that fruit bodies were larger in the higher temperature condition, but were brighter in the lower temperature condition. Additionally, fruit body physiology was found to be not affected by temperature. In the PE greenhouse, the fresh weight of fruit body was higher in mid-June and early July. Therefore, it was possible to effectively control the growth period of the mushrooms during a high-temperature period. The findings indicate the potential to cultivate A. polytricha ‘Geoni’in a simple PE greenhouse that is not cooled in summer, thus reducing energy costs.

PURPOSES: The object of this study is to select appropriate inorganic materials, and find the best mixing formula to secure fast curing time and enough initial strength, and then to evaluate the durability of the asphalt mixtures according to the degree of addition of the compound manufactured by the determined blending ratio. METHODS : The breaking time and reactivity between seven kinds of inorganic minerals, and the selected recycled aggregate and emulsified asphalt were compared to determine the best initial curing strength for the mixtures. Then, three inorganic materials were chosen as the materials that provide good breaking time and reactivity, and the best mixing formula for the three materials was determined. The chemical composition of the compound manufactured using the mixing formula was analyzed by energy dispersive x-ray system method. Finally, indirect tensile strength (ITS) test was performed (for two days) at room temperature to determine the proper amount of additives that will provide the best initial strength. RESULTS: From the results of the reactivity test, the best mixing formula (A:C:G = 60:30:10) for the three selected inorganic materials with short braking time and high reactivity was determined. The four types of cold reclaimed asphalt mixtures for ITS testing were manufactured by adding the inorganic material compounds at 0%, 3%, 5%, and 7%, and the ITS values were measured after two curing days. The ITS values at 5% and 7% were 0.308 MPa and 0.415 MPa, respectively. The results of quality control tests (Marshall stability, porosity, flow value, etc.) at 5% and 7% satisfied the specification criterion for the cold recycled asphalt mixtures. CONCLUSIONS : The selected inorganic materials (A, C, and G) and the best mixing formula (A:C:G = 60:30:10) accelerated the reaction with emulsified asphalt and shortened the curing time. Depending on the inorganic material used, the breaking time and reactivity can be directly related or unrelated. This is because of the chemical compositions of recycled aggregates, infiltrated foreign matter, and chemical reactions between the inorganic materials and other materials. Therefore, it is important to select the proper materials and the best mixing formula when evaluating the characteristics of the practically used materials such as recycled aggregates, inorganic materials, and emulsified asphalt.

이온성 액체를 이용하여 질산 용액으로부터 Am(Ⅲ)과 Eu(Ⅲ)의 추출 거동을 조사하고 이온성 액체의 활용가능성을 살펴보았다. 이온성 액체로는 1-alkyl-3- methylimidazolium bis(trifluoromethylsulfonyl)imide ([Cnmim][Tf2N])을 사용하였고, noctyl( phenyl)-N,N-diisobutyl carbamoylmethyl phosphine oxide (CMPO)와 tri-n-butylphosphate (TBP)를 추출제로 사용하여, Am(Ⅲ)과 Eu(Ⅲ)의 추출 분배계수를 질산농도, CMPO, TBP와 같은 변수들의 함수로서 측정하였다. 이온성 액체를 사용함으로써 기존의 n-doodecane (n-DD)과 비교하여 추출 효율이 현저히 증가하였다. 질산 용액의 농도가 높을수록 Am(Ⅲ)과 Eu(Ⅲ)의 추출률은 감소하였으며, Eu(Ⅲ)의 추출률은 Am(Ⅲ)보다 전반적으로 작았다. 이온성 액체를 이용한 Am(Ⅲ)과 Eu(Ⅲ)의 추출 메카니즘은 n-DD와 같은 분자성 유기용매를 사용하는 경우와는 달리 양이온 교환 메카니즘에 의해 일어나는 것으로 판명되었다. 사용한 모든 이온성 액체에 대하여 Am(Ⅲ)과 Eu(Ⅲ)의 추출 분배계수는 CMPO의 농도가 높을수록 증가 하고, CMPO 농도에 대한 추출 데이터의 직선 기울기 값은 약 3.0으로 이온성 액체를 이용한 Am(Ⅲ)과 Eu(Ⅲ)의 추출반응에서 3분자의 CMPO가 복합착물을 형성하는 것으로 나타났다.

As an approach for estimation of the droplet size in the molten salt-liquid metal extraction process, a droplet formation experiment at room temperature was conducted to evaluate the applicability of the Scheele-Meister model with water-mercury system as a surrogate that is similar to the molten salt-liquid metal system. In the experiment, droplets were formed through the nozzle and the droplet size was measured using a digital camera and image analysis software. As nozzles, commercially available needles with inner diameters (ID) of 0.018 cm and 0.025 cm and self-fabricated nozzles with 3-holes (ID: 0.0135 cm), 4-holes (ID: 0.0135 cm), and 2-holes (ID: 0.0148 cm) were used. The mercury penetration lengths in the nozzles were 1.3 cm for the needles and 0.5 cm for the self-fabricated nozzles. The droplets formed from each nozzle maintained stable spherical shape up to 20 cm below the nozzle. The droplet size measurements were within a 10% error range when compared to the Scheele-Meister model estimates. The experimental results show th

Although assisted reproductive technology (ART) has been developed in many mammalian species including cows, the only embryo preservation technology that is available is cryopreservation. In the present study, small molecules were used to preserve embryos at room temperature. The basic medium for embryo preservation consisted of 1% BSA non-cryopreservation medium (BNC) instead of fetal bovine serum (FBS). To maintain survival and prevent damage during embryo storage, three candidate small molecules were selected—CHIR99021, Y-27632 and Thiazovivin—and their concentrations were optimized. Then, the embryos in the small molecule supplemented preservation medium were stored at room temperature. The viability and hatching rate of embryos stored at 10°C were greater for Y-27632-BNC and CHIR99021+Y-27632-BNC compared to BNC. However, the rate was lower for Thiazovivin-BNC compared to BNC. Although there were no surviving embryos after storage at 20°C, the viability and hatching rate of embryos significantly increased in Y-27632-BNC and CHIR99021+Y-27632-BNC compared to BNC. The mechanism by which small molecules enhance survival of embryos during storage was investigated, and expression of heat shock protein 70 was observed to increase. The findings of this work may be useful in improving ART in the agricultural field.

The CO2 separation membranes based on a graft copolymer consisting of hydrophobic poly(ethylene-alt-maleic anhydride) (PEMA) backbone and hydrophilic poly(propylene glycol) PPG side chains were fabricated by a facile one-pot process. The reaction between O-(2-aminopropyl)-O’-(2-methoxyethyl) polypropylene glycol (AMPPG) and PEMA was conducted in butanol at room-temperature. Without any post-treatment, the as-synthesized PEMA-g-PPG solution could be directly coated onto a microporous polysulfone support to fabricate thin-film composite membranes. The PEMA-g-PPG membrane exhibited high selectivity (82.6 for CO2/N2 and 26.8 for CO2/CH4) and good CO2 permeability (99.1 Barrer), which is a close value to the upper boundary limit (2008). The PEMA-g-PPG membrane could be commercially feasible owing to simple, inexpensive and scalable process.

Quality assessment of sweet persimmon or “Fuyu” was evaluated over room temperature distribution periods after 40-day storage at 0oC cold room. All Hunter’s values (L, a, and b) of sweet persimmon were significantly decreased after 4-day room temperature distribution while the flesh firmness was drastically decreased after 3-day room temperature distribution. Glucose and fructose contents were significantly increased by the degradation of sucrose after 3-day room temperature distribution. The highest extraction yield was obtained in the flesh of persimmon. Extraction yields of each part of “Fuyu” persimmon were 15.53% for flesh, 10.53 for seed, and 13.83 for flower bud. However, the total phenolic content of flesh was 4.8 μg/mg which was extremely lower than that of the seed (175.5 μg/ mg) and flower bud (178.2 μg/mg) of sweet persimmon. With high phenolic content, both the flower bud and seed of sweet persimmon showed excellent antioxidant activities by 2,2-diphenyl-1-picrylhydrazyl (DPPH) and 2,2'-azinobis( 3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) free radical scavenging test. The results showed a great potential for byproducts (seed and flower bud) of long-term, cold-stored sweet persimmon “Fuyu” as a good antioxidant material for novel functional foods.