본 연구에서는 자연분해재 펠릿과 polyethylene들을 이용해 LDPE와 신장율과 인장강도가 유사한 생붕괴성 플라스틱 필름들을 제조하였다. 식품 포장재로서의 안전성, 광분해성, 열분해성 및 곰팡이 생분해성을 평가한 결과 제작된 생붕괴성 플라스틱 필름들은 식품 포장재로 사용하기에 안전하고 LDPE 필름에 비해 상대적으로 우수한 분해 특성을 나타내어 환경친화적인 식품 포장 소재로 사용될 가능성을 보여주었다.

쌀단백질을 효소분해하여 제조한 배양액으로 천연조미소재로 사용할 효모추출물을 제조하기 위한 최적 공정조건을 조사하였다. 쌀단백질(5%, w/w)을 단백분해효소인 Delvolase®로 효소분해한 상등분획에 3%(w/w) 수준으로 포도당을 첨가한 배지 조건이 가장 적절하였으며 이 조건에서 2.3 g/L의 효모를 회수하였다. 회수한 효모에는 RNA가 188.1 mg/g수준으로 함유되어 있었으며 GMP 및 IMP는 각각 650.33±48 μg/g, 69±21 μg/g 함유되어 있었다. 이와 같은 효모추출물에 효모배양액의 제조 후 남은 쌀단백질 잔사의 효소분해물(Rrh)을 혼합하면 감칠맛이 상승하였는데 미각센서 분석기로 측정한 결과 효모추출물의 감칠맛이 4.88에서 Rrh의 첨가 후에는 9.25로 증가하였으며 관능검사에서도 감칠맛의 증가를 확인할 수 있었다. 이와 같이 효모추출물에 쌀단백질 잔사의 효소분해물이 추가되면 효소분해 과정 중 생성된 다양한 맛 성분으로 인해 감칠맛이 상승되어 전체적인 기호도가 높아지므로 천연조미소재로서의 활용이 가능함을 알 수 있었다.

In this research, the indium dissolution properties of the waste LCD panel powders were investigated as a function of milling time fabricated by high-energy ball milling (HEBM) process. The particle morphology of waste LCD panel powders changed from sharp and irregular shape of initial cullet to spherical shape with an increase in milling time. The particle size quickly decreased to 15 until the first minute, then decreased gradually about 6 with presence of agglomerated particles after 5 minutes, which increased gradually reaching a uniform size of 13 consist of agglomerated particles after 30 minutes. The glass recovery, after dissolution, was over 99% at initial cullet, which decreased to 90.1 and 78.6% with increasing milling time of 1 and 30 minute respectively, due to a loss in remaining powder of the surface ball and jar, as well as the filter paper. The dissolution amount of indium out of the initial cullet was 208 ppm before milling, turning into 223 ppm for the mechanically milled powder after 1 minute, and nearly 146~125 ppm with further increase in milling time because of the reaction surface decrease of powders due to agglomeration. With this process, maximum dissolving indium amount (223 ppm) could be achieved at a particle size of 15 with 1 minute of milling.

In this study, gradient porous Al-Cu sintered body was fabricated by powder metallurgy processing. Al-Cu powder mixtures were prepared by low energy ball milling with various milling time. After ball milling for 3h, the shape of powder mixtures changed to spherical type with size of 100~500 . Subsequently, Al-Cu powder mixtures were classified (under 150, 150~300 and over 300 ) and compacted (20, 50 and 100 MPa). Then, they were sintered at for various holding time (10, 30, 60 and 120 min) in atmosphere. The sintered bodies had 32~45% of porosity. As a result, the optimum holding time was determined to be 60 min at and sintered bodies with various porosity were obtained by controlling the compacting pressure.

In order to improve the weak mechanical properties of cast Mg alloys, Mg- (at%) alloy powders were synthesized using gas atomization, a typical rapid solidification process. The powders consist of fine dendrite structures less than 3 in arm spacing. In order to fabricate a bulk form, the Mg powders were compacted using magnetic pulse compaction (MPC) under various processing parameters of pressure and temperature. The effects of the processing parameters on the microstructure and mechanical properties were systematically investigated.

In order to fabricate the porous metal with controlled pore characteristics, unique processing by using metal oxide powder as the source and camphene as the sublimable material is introduced. CuO powder was selected as the source for the formation of Cu metal via hydrogen reduction. Camphene-based CuO slurry, prepared by milling at with a small amount of dispersant, was frozen at . Pores were generated subsequently by sublimation of the camphene. The green body was hydrogen-reduced at for 30 min, and sintered at for 1 h. Microstructural analysis revealed that the sintered Cu showed aligned large pore channels parallel to the camphene growth direction, and fine pores are formed around the large pore. Also, it showed that the pore size was controllable by the slurry concentration.

[ Zn2(1-x)MnxSiO4 ]0.07≤x≤0.15) green phosphor was prepared by solid state reaction. The first heating was at 900˚C-1250˚C in air for 3 hours and the second heating was at 900˚C in N2/H2(95%/5%) for 2 hours. The size effect of SiO2 in forming Zn2SiO4 was investigated. The temperature for obtaining single phase Zn2SiO4 was lowered from 1100˚C to 1000˚C by decreasing the SiO2 particle size from micro size to submicro size. The effect of the activators for the Photoluminescence (PL) intensity of Zn2SiO4:Mn2+ was also investigated. The PL intensity properties of the phosphors were investigated under vacuum ultraviolet excitation (147 nm). The emission spectrum peak was between 520 nm and 530 nm, which was involved in green emission area. MnCl2·4H2O, the activator source, was more effective in providing high emission intensity than MnCO3. The optimum conditions for the best optical properties of Zn2SiO4:Mn2+ were at x = 0.11 and 1100˚C. In these conditions, the phosphor particle shape was well dispersed spherical and its size was 200 nm.

The purpose of this study was to determine the optimal mixing conditions for three different amounts of mulberry juice, sugar, and agar powder for Yanggaeng prepared with mulberry juice. The experiment was designed according to the central composite design for estimating the response surface, which demonstrated 16 experimental points including 2 replicates for mulberry juice, sugar and agar powder each?? The mechanical and sensory properties of test materials were measured, and these values were applied to the mathematical models. A canonical form and perturbation plot showed the influence of each ingredient on the final product mixture. Measurement results of the mechanical properties showed a significant increase or decrease?? in pH, sugar content, water content, viscosity, l-value, a-value, b-value, hardness, springiness, chewiness, gumminess, cohesiveness. Also the sensory measurements showed a significant improvement?? in appearance, flavor, color, sweetness, texture, overall quality. As a result, the optimum formulation by numerical and graphical methods was calculated as mulberry juice 41.99 g, sugar 90.00 g, agar powder 3.18 g.

We evaluated the sensory characteristics of Gangjung base obtained from various manufacturers, using a sensory descriptive analysis. Significant differences were observed for all sensory attributes of Gangjung samples with the exception of 'toothpacking'. Sample A showed high intensities for 'external color', 'external roughness', 'sweetness', 'toasted soybean powder flavor', 'crispness', 'fracturability', 'oiliness', and 'loose particles,' whereas it had low intensities for 'rice flour flavor', 'hardness', and 'toughness' compared to those of other samples. Sample B had more 'sourness', 'butyric acid flavor', 'fermented rice flavor', and 'degree of melting' but lower 'air cell size', 'fracturability', and 'flake roughness'. Sample C showed high intensities for 'expansion', 'hardness', 'crispness', and 'flake roughness', whereas sample D showed low intensities for 'expansion' and 'sourness'. These results indicate that Gangjung base samples are markedly different depending on the manufacturer.

The processes for the preparation of ZnO powder by using EAF(electric arc furnace)dust was studied by wetting method which are divided to two steps, carried out of the elution processes by various concentrations of sulfuric acid is reacted with EAF dust as the former, and the latter were performed by a number of specified processes, which are leaching process depends on various pH, cementation, ozone and heat treatment processes etc. Experimental results showed that the appropriate pH range is pH7.5~8.0 and the resulting zinc content is range of 37~38%, the residual quantities of the heavy metals are less than 3ppm individually by cementation process except Mn, even though the Mn metal could not be removed by cementation process but was removed up to 0.2ppm by the ozone process from 70ppm initially. Finally, 80.2% of ZnO was obtained by the heat treatment at 500℃.

The successful and sustainable growth of SMEs depends on their ability of strengthen their competitiveness in quality and cost and service more than anything else as a fundamental of operation. Among these key competitive factors of SMEs, quality is the most critical factor in manufacturing business fields. There are many different ways to improve the quality performance but it needs proper management decision to choose the best way what can maximize outputs with minimum inputs. And it needs effective measurement methods and some indicators to analysis the quality performance properly. The quality cost is one of the simplest key indicators to measure the quality performance and the effectiveness of quality related management decisions. In this study, through survey on local SMEs, we found that their average annual quality cost ratio versus turnover - total amount of annual quality cost divided by annual turnover - is around 3.69% excluded some SME's performances what have different quality control measures with others. And we found some results what corresponded with the early studies on the correlations between those categorized quality costs factors and some discrepancies between some of the literature model and the early case study results as follows. There were negative correlations between the Prevention costs and the External failure costs, and the Appraisal costs and the External failure costs, and there was positive correlation between the Appraisal costs and Internal failure costs same as early studies. But, we couldn't found any strong negative correlations between the Cost of control - Prevention costs & Appraisal costs - and the Cost of Failure of control - Internal & External failure costs -.

금속-세라믹 복합 분리막은 특히 석탄가스화 공정이나 메탄 개질에서 발생되는 혼합가스로부터 수소를 분리하기 위해 개발되어졌다. 수소투과 금속인 팔라듐과 세라믹 지지체로 Y2O3-stabilized ZrO2 (YSZ)를 이용하여 cermet 수소분리막을 제조하였다. 이렇게 제조된 분리막은 팔라듐의 연속상이 잘 발달된 치밀 구조를 보였다. Pd/YSZ 분리막의 수소 투과량은 100% 수소를 흘려 0.5~2 atm에서 측정되었다. 수소 투과량은 450℃, 2 atm에서 0.333 mL/min·㎠를 보였다. 수소 투과 후 분리막의 표면과 단면에서 균열이 형성되었다.

The main objective of the present paper is to conduct a depth analysis of the structural relationship among cooperation of manufacturing corporations, their development of new products and performance in view of an empirical study. The findings of this study could be summed up as follows: First, from the analysis of relationship between cooperation of manufacturing corporations and development of new products, it was found out that there is a positive relationship among such factors of new product development as development process, organizational culture and substructure when cooperation among corporations becomes intensive. Second, the analysis of relationship between development of new products and financial outcomes showed that the factors of new product development like organizational culture and substructure do influence financial performance, while the development process don't. Third, in terms of relationship between factors of new product development and non-financial performance, it was analyzed that non-financial performance can be affected by such factors of new product development as development process, organizational culture and substructure.

In order to make high-purity ferro-manganese from Mn3O4 waste dust, the application of aluminothermite process to the reduction of the waste dust was investigated. The mixture from Mn3O4 dust as metallic source and Al metal powder as the reductant ignited, and reduced with an extremely intense exothermic reaction. The rapid propagation of the aluminothermite reaction occurred spontaneously and stably by ignition of the mixture. The Manganese having some alloy elements emerged as liquids due to the high temperatures reached up to about 2,500℃ and separated from the liquid by their differences of specific gravity. The result of thermite reaction showed the fact that can be obtained high purity ferro-manganese which have over about 90% of manganese content and lower impurities such as C, P, S than those of KS D3712 specification. The recovery of manganese from Mn3O4 dust was lower level of about 65% than about 75% from manganese ore by electric furnace process, that is due to spatter loss because of its extremely intense thermite reaction. But it will be improved by the process designed to provide CaO as the cooler or to use the Al metal powder having larger particle size distribution.

The purpose of this paper is to suggest a supplier and buyer’s pricing decision strategy model with discount-policy over a long-term replenishment contract in a supply chain environment by small and medium size manufacturing company. We assume that the bu

In this study was analyzed substances that high contribute to odor strength degree which emitted from the painting, the plating, the casting, the rubber manufacturing, and the used oil refining facilities in Gwangju Hanam industrial complex. In order to this, we analyzed two types of nitrogen compounds, five types of sulfur compounds, thirteen types of the aldehyde, and ten types of volatile organic compounds discharged from an outlet for antipollution facilities. The results are as following high contribution rate sustances to odor strenth was ordered butylaldehyde (73.8%) ＞ acetaldehyde (17.7%) ＞ propionaldehyde (4.9%) at painting facilities. At plating facilities, it was ordered Acetaldehyde (59.0%) ＞ ammonia (19.1) ＞ hydrogen sulfide (13.1%). At casting facilities, it was ordered Hydrogen sulfide (65.9%) ＞ acetaldehyde (17.2%) ＞ sulfur dioxide(5.2%). At rubber manufacturing facilities, it was ordered i-valeraldehyde (35.0%) ＞ butylaldehyde (32.0%) ＞ n-valeraldehyde (13.3%) and at used oil refinery facilities, it was ordered Acetaldehyde (36.8%)＞ butylaldehyde (33.6%) ＞ sulfur dioxide (14.5%).

In order to investigate the microstructure and mechanical properties of WC-10 wt% Co insert tool alloy fabricated by PIM (Powder Injection Molding) process, the feedstock of WC-10 wt% and wax used as a kind of binder were mixed together by two blade mixer. After injection molding, the debinding process was carried out by two-steps. First, solvent extraction, in which the binder was eliminated by putting the specimen into normal hexane for 24 hrs at , and subsequently thermal debinding which was conducted at and for 6 hrs in the mixed gas of , respectively. Meantime, in order to compensate the decarburization due to hydrogen, 1.2~1.8% of carbon was added to ensure the integrity of the phase. Finally, the specimens were sintered in vacuum under different temperatures, and the relative density of 99.8% and hardness of 2100 Hv can be achieved when sintered at , even the TRS is lower than the conventional sintering process.

Al/AlN composites were synthesized by mechanical alloying using process control agents(PCAs). Three different PCAs which contain N element, were examined to see the effectiveness of ball-milling and the nitridation during sintering. Among examined PCAs, was the most effective to facilitate ball-milling and to form nitrides during a subsequent sintering. By a proper control of ball-milling and sintering, we could obtained surface-hardened Al-based composites.

W-ZrC and W-HfC composite powders were fabricated by the Plasma Alloying & Spheroidization (PAS) method and the powders were sprayed into hybrid coating layers by using Low Vacuum Plasma Spray (LVPS) process, respectively. Microstructure, mechanical properties, and ablation characteristics of the fabricated coating layers were investigated. The LVPS process led to successful production of W-Carbide hybrid coatings, approximately 400 or above in thickness. As the substrate preheating temperature increased from to , the hardness of the W-ZrC coating layer increased due to decreased porosity. Vickers hardness showed higher value (about 108.4 HV) in W-ZrC hybrid coating material compared to that of W-HfC while adhesive strength was found to be similar in both coating layers. The plasma torch test revealed good ablation resistance of the W-Carbide hybrid coating layers. The relatively high performance W-ZrC coating layer at the elevated temperature is thought to be attributed to both the strengthening effect of ZrC particle remained in the layer and the formation of ZrO2 phase with high temperature stability.

In the current study, the effects of particle size on compaction behavior of water-atomized pure iron powders are investigated. The iron powders are assorted into three groups depending on the particle size; 20-45 , 75-106 , and 150-180 for the compaction experiments. The powder compaction procedures are processed with pressure of 200, 400, 600, and 800 MPa in a cylindrical die. After the compaction stage, the group having 150-180 of particle size distribution shows the best densification behavior and reaches the highest green density. The reason for these results can be explained by the largest average grain size in the largest particle group, due to the low plastic deformation resistance in large grain sized materials.