우리나라에서 공용중인 시설물은 총 172,111개로 집계되고 있으며, 그 중 교량은 34,199개로 사회 기반시설 중 가장 많은 비중을 차지한다. 이러한 교량은 공용하중, 온도, 습도 등에 의해 거더간 신축 량이 발생하게 되고 신축량 발생으로 인한 유간거리에 대해 차량의 통행 안정성 및 주행성 확보를 위 한 신축이음장치를 설치하게 된다. 신축이음장치를 설치하여 차량의 통행 안정성 및 주행성을 확보할 수 있지만 누수 및 퇴적물 낙하 등을 직접적으로 방지하지 못하여 고무지수재를 별도로 설치하게 된 다. 하지만 이러한 고무지수재는 다양한 원인에 의해 쉽게 손상이 발생한다. 손상된 고무지수재를 통 해 거더의 부식, 교량하부 인명사고 등 다양한 2차 피해가 발생할 수 있다. 피해방지를 위한 교량의 유지관리를 지속적으로 수행하고 있지만 고무지수재 특성상 지속적인 교체가 불가피한 실정이다. 따라 서 본 연구에서는 기존 신축이음장치에 활용되는 고무지수재의 문제점을 해결하기 위하여 초탄성 형 상기억합금을 활용한 새로운 지수재 개발 연구를 수행하였다. 이에 대해 초탄성 형상기억합금 지수재 와 고무지수재에 대한 유한요소해석을 수행하고 비교 및 분석하였으며, 하중 제거 후 원형으로 복원되 는 효과를 통해 지속 사용 가능한 지수재 연구를 검증하였다.

실물 크기로 제작된 L형 프리캐스트 옹벽의 저판부에 대한 휨 실험을 수행하여, 프리캐스트 부분과 현장타설 부분의 연결방법에 따른 구조적 거동을 분석하였다. 연결방법은 기존의 일반적인 철근 겹이 음 방식과 최근 새롭게 개발된 비접촉식 커플러 방식 두 가지를 적용하였다. 실험체 셋팅을 위하여 현 장타설부를 갖는 프리캐스트 L형 옹벽을 제작하여 벽체를 반력벽에 고정하고, 벽체 하단에 힌지 지점 을 설치하였다. 또한 L형 옹벽 저판부의 현장타설부 중간 지점에 하중을 재하하여 고정단 조건으로 인한 전단 및 휨이 연결부에 작용하도록 하였다. 실험결과를 보면 비접촉식 커플러를 적용한 옹벽 저 판부에서 좀더 높은 강성을 보이는 것을 확인하였으며, 최대 강도에는 차이가 없었다. 비접촉식 커플 러는 철근의 부착력에 의해 구조적 성능을 확보하는데 이를 위하여 확대마디, 연결 철근, 스파이럴바 등이 사용된다. 이러한 구성품들로 인하여 비접촉식 커플러 적용 구간에 철근 단면적 향상 효과가 나 타나 높은 강성을 갖게 된 것으로 판단 된다. 비접촉식 커플러는 기존 겹이음에 비해 이음길이를 50% 수준으로 감소할 수 있어 대형 프리캐스트 구조물의 제작에 활용되는데 이번 실험을 통하여 충분한 구조 성능을 가지고 있음을 확인하였다.

This study presents a novel method for addressing the issue of high-concentration contaminants (ammonium, phosphate, antibiotics) in leachate arising from decomposing livestock carcasses. Antibiotics, developed to eliminate microorganisms, often have low biodegradability and can persist in the ecosystem. This research proposes design elements to prevent contamination spread from carcass burial sites. The adsorbents used were low-grade charcoal (an industrial by-product), Alum-based Adsorbent (ABA), and Zeolite, a natural substance. These effectively removed the main leachate contaminants: low-grade charcoal for antibiotics (initial concentration 1.05 mg/L, removal rate 73.4%), ABA for phosphate (initial concentration 2.53 mg/L, removal rate 99.9%), and zeolite for ammonium (initial concentration 38.92 mg/L, removal rate 100.0%). The optimal mix ratio for purifying leachate is 1:1:10 of low-grade charcoal, ABA, and zeolite. The average adsorbent usage per burial site was 1,800 kg, costing KRW 2,000,000 per ton. The cost for the minimum leachate volume (about 12.4 m3) per site is KRW 2,880,000, and for the maximum volume (about 19.7 m3) is KRW 4,620,000. These findings contribute to resolving issues related to livestock carcass burial sites and suggest post-management strategies by advocating for the effective use of adsorbents in leachate purification.

This study investigated species identification and labeling compliance of 48 shrimp products sold in the Korean online markets. Species identification was conducted using the standard DNA barcoding method, using the cytochrome c oxidase subunit I gene. The obtained sequences were compared with those deposited in the NCBI GenBank and BOLD Systems databases. Additionally, phylogenetic analysis was performed to further verify the identified shrimp species. Consequently, 16 shrimp species were identified, including Penaeus vannamei, Pandalus borealis, Palaemon gravieri, Leptochela gracilis, Penaeus monodon, Pleoticus muelleri, Metapenaeopsis dalei, Euphausia pacifica, Lebbeus groenlandicus, Trachypenaeus curvirostris, Argis lar, Metanephrops thomsoni, Metapenaeopsis barbata, Alpheus japonicus, Penaeus chinensis, and Mierspenaeopsis hardwickii. The most prevalent species was Penaeus vannamei, found in 45.8% of the analyzed products. A significant mislabeling rate of 72.9% was found; however, upon excluding generic names such as shrimp, the mislabeling rate reduced to 10.4%. The mislabeling rate was higher in highly-processed products (89.3%) compared with that in minimally-processed products (50%). No correlation was found between the country of origin and mislabeling rate. The results of this study provide crucial data for future monitoring of shrimp products and improving the labeling of shrimp species in Korea.

In this study, based on an analysis of two DNA barcode markers (cytochrome c oxidase subunit I and cytochrome b genes), we performed species identification and monitored labeling compliance for 50 commercial pufferfish products sold in on-line markets in Korea. Using these barcode sequences as a query for species identification and phylogenetic analysis, we screened the GenBank database. A total of seven pufferfish species (Takifugu chinensis, T. pseudommus, T. xanthopterus, T. alboplumbeus, T. porphyreus, T. vermicularis, and Lagocephalus cheesemanii) were identified and we detected 35 products (70%) that were non-compliant with the corresponding label information. Moreover, the labels on 12 commercial products contained only the general common name (i.e., pufferfish), although not the scientific or Korean names for the 21 edible pufferfish species. Furthermore, the proportion of mislabeled highly processed products (n = 9, 81.8%) was higher than that of simply processed products (n = 26, 66.7%). With respect to the country of origin, the percentage of mislabeled Chinese products (n = 8, 80%) was higher than that of Korean products (n = 26, 66.7%). In addition, the market and dialect names of different pufferfish species were labeled only as Jolbok or Milbok, whereas two non-edible pufferfish species (T. vermicularis and T. pseudommus) were used in six commercial pufferfish products described as JolboK and Gumbok on their labels, which could be attributable to the complex classification system used for pufferfish. These monitoring results highlight the necessity to develop genetic methods that can be used to identify the 21 edible pufferfish species, as well as the need for regulatory monitoring of commercial pufferfish products.

The importance of Structural Health Monitoring (SHM) in the industry is increasing due to various loads, such as earthquakes and wind, having a significant impact on the performance of structures and equipment. Estimating responses is crucial for the effective health management of these assets. However, using numerous sensors in facilities and equipment for response estimation causes economic challenges. Additionally, it could require a response from locations where sensors cannot be attached. Digital twin technology has garnered significant attention in the industry to address these challenges. This paper constructs a digital twin system utilizing the Long Short-Term Memory (LSTM) model to estimate responses in a pipe system under simultaneous seismic load and arbitrary loads. The performance of the data-driven digital twin system was verified through a comparative analysis of experimental data, demonstrating that the constructed digital twin system successfully estimated the responses.

식량 작물의 확보 및 생산량 예측은 국가 발전에 있어 필수적이며, 국가 경제뿐만 아니라 전 세계 식량 안보에 기여 한다. 최근 환경오염으로 인한 이상기후는 식량 작물 생산량에 직ㆍ간접적으로 부정적 영향을 끼치고 있어, 작물 수확량 예측 불확실성이 높아지고 있다. 특히, 노지 작물의 경우 생산량 감소와 품질 저하 문제가 화두 되고 있다. 이러한 문제는 농가들뿐만 아니라 소비자들에게도 큰 피해를 안겨주고 있다. 이러한 생산량 예측 이슈를 해결하기 위해 최근에는 인공지능 기술이 농업 분야에도 활발히 적용되고 있다. 작물 수확량의 정확한 예측을 위한 머신러닝 기반 연구가 집중적으로 수행되고 있다. 따라서, 본 연구에서는 이와 같은 인공지능 기반의 노지 작물 수확량 예측 기술(머신러닝, 딥러닝, 하이브리드 모델 등) 현황 및 작물 수확량에 가장 영향을 많이 끼치는 모델 파라미터 등을 조사하였다.

Freshwater jellyfish, a type of jellyfish exclusively found in freshwater, has a limited number of species but is found globally. However, their ecology and causes of occurrence are largely unknown. Therefore, understanding the distribution of polyps, which produce the larvae of freshwater jellyfish, can provide important data for comprehending their ecology. This study aims to explore the COI gene of freshwater jellyfish using environmental DNA from the microbial film in the Miho River system. Among the 12 survey points in the Miho River watershed, genetic material of freshwater jellyfish was detected in 8 points, mainly located upstream near reservoirs. These genetic materials were identified as genes of the well-known freshwater jellyfish species, Craspedacusta sowerbii. Notably, the C. sowerbii genes found in the Miho River watershed survey points were closely related to a species previously discovered in Italy. Consequently, utilizing environmental DNA to explore the genetic traces of freshwater jellyfish enables rapid screening of areas with a high likelihood of freshwater jellyfish occurrence. This approach is deemed to provide crucial information for understanding the distribution and ecology of freshwater jellyfish in Korea.

Cyanobacteria Pseudanabaena strains are known to produce 2-MIB (odorous material) in freshwater systems, thereby causing problems in water use. However, their physiological responses to environmental factors in relation with 2-MIB production is not well explored. This study was conducted to evaluate the effect of temperature on the growth and 2-MIB production of Pseudanabaena redekei. The experimental cyanobacteria strains were separated from the Uiam Reservoir (North Han River) and cultured in the BG-11 medium. Temperature was set to 10, 15, 20, 25, and 30℃ for the experiment, in the reflection of the seasonal water temperature variation in situ. For each temperature treatment, cyanobacterial biomass (Chl-a) and 2-MIB concentration (intra-cellular and extra-cellular fractions) were measured every 2 days for 18 days. Both maximal growth and total 2-MIB production of P. redekei appeared at 30℃. While intra-cellular 2-MIB contents were similar (26~29 ng L-1) regardless of treated temperatures, extra-cellular 2-MIB concentration was higher only in high temperature conditions (25~30℃), indicating that the extents of 2-MIB biosynthesis and release by P. redekei vary with temperature. The 2-MIB productivity of P. redekei was much higher in low-temperature conditions (10~15℃) than high temperature conditions (25~30℃). This study demonstrated that temperature was a critical factor contributing to 2-MIB biosynthesis and its release in cell growth (r=0.605, p<0.01). These results are important to understand the dynamics of 2-MIB in the field and thereby provide basic information for managing odorous material in drinking water resources.

Cyanobacterial resting cells, such as akinetes, are important seed cells for cyanobacteria’s early development and bloom. Due to their importance, various methods have been attempted to isolate resting cells present in the sediment. Ludox is a solution mainly used for cell separation in marine sediments, but finding an accurate method for use in freshwater is difficult. This study compared the two most commonly used Ludox methods (direct sediment treatment and sediment distilled water suspension treatment). Furthermore, we proposed a highly efficient method for isolating cyanobacterial resting cells and eDNA amplification from freshwater sediments. Most of the resting cells found in the sediment were akinete to the Nostocale and were similar to those of Dolichospermum, Cylindrospermum, and Aphanizomenon. Twenty times more akinetes were found in the conical tube column using the sediment that had no treatment than in the sample treated by suspending the sediment in distilled water. Akinete separated through Ludox were mainly spread over the upper and lower layers in the column rather than concentrated at a specific depth in the column layer. The mibC, Geo, and 16S rDNA genes were successfully amplified using the sediment directly in the sample. However, the amplification products of all genes were not found in the sample in which the sediment was suspended in distilled water. Therefore, 5 g to 10 g of sediment is used without pretreatment when isolating cyanobacterial resting cells from freshwater sediment. Cell isolation and gene amplification efficiency are high when four times the volume of Ludox is added. The Ludox treatment method presented in this study isolates cyanobacterial resting cells in freshwater sediment, and the same efficiency may not appear in other biotas. Therefore, to apply Ludox to the separation of other biotas, it is necessary to conduct a pre-experiment to determine the sediment pretreatment method and the water layer where the target organism exists.

Environmental DNA (eDNA) can exist in both intracellular and extracellular forms in natural ecosystems. When targeting harmful cyanobacteria, extracellular eDNA indicates the presence of traces of cyanobacteria, while intracellular eDNA indicates the potential for cyanobacteria to occur. However, identifying the “actual” potential for harmful cyanobacteria to occur is difficult using the existing sediment eDNA analysis method, which uses silica beads and cannot distinguish between these two forms of eDNA. This study analyzes the applicability of a density gradient centrifugation method (Ludox method) that can selectively analyze intracellular eDNA in sediment to overcome the limitations of conventional sediment eDNA analysis. PCR was used to amplify the extracted eDNA based on the two different methods, and the relative amount of gene amplification was compared using electrophoresis and Image J application. While the conventional bead beating method uses sediment as it is to extract eDNA, it is unknown whether the mic gene amplified from eDNA exists in the cyanobacterial cell or only outside of the cell. However, since the Ludox method concentrates the intracellular eDNA of the sediment through filtration and density gradient, only the mic gene present in the cyanobacteria cells could be amplified. Furthermore, the bead beating method can analyze up to 1 g of sediment at a time, whereas the Ludox method can analyze 5 g to 30 g at a time. This gram of sediments makes it possible to search for even a small amount of mic gene that cannot be searched by conventional bead beating method. In this study, the Ludox method secured sufficient intracellular gene concentration and clearly distinguished intracellular and extracellular eDNA, enabling more accurate and detailed potential analysis. By using the Ludox method for environmental RNA expression and next-generation sequencing (NGS) of harmful cyanobacteria in the sediment, it will be possible to analyze the potential more realistically.

Targeting Microcystin (MC), which is most abundantly detected in the North-Han River water area, we analyzed the relationship between the MC biosynthesis gene (mcyA gene), cyanobacteria cell density, and MC concentration, derived an RNA-MC conversion formula, and derived the cyanobacteria. The concentration of MC present in cells was predicted. In the North-Han River waters, the mcyA gene was found mainly at downstream sites of the North-Han River after Muk-Hyeon Stream junction, and higher copy numbers were found on average than other sites. In the Uiam Lake waters upstream of the North-Han River, the mcyA gene copy number increased at the Kong-Ji Stream point, and after September, the mcyA gene copy number decreased throughout the North-Han River waters. The expression of the mcyA gene was concentrated in the short period of summer due to the spatio-temporal difference between upstream and downstream water bodies. The mcyA gene expression level was not only highly correlated with MC concentration, but also correlated with the cell density of Microcystis aeruginosa and Dolichospermum circinale, which are known to biosynthesize MC. Six conversion formulas derived based on the RNA-MC relationship showed statistical significance (p<0.05) and exhibited high correlation coefficients (r) of 0.9 or higher. The expression level of MC biosynthesis gene present in eRNA determines the synthesis of cyanotoxin substances in water, quickly quantifies gene activity, and can be fully utilized for early warning of MC development.

PURPOSES : With the recent enactment of the 「Framework Act on Sustainable Infrastructure Management」 in Korea, the establishment of mid- to long-term management plans for social infrastructure and the feasibility evaluation of maintenance projects have become mandatory. To this end, the life cycle cost analysis is essential. However, owing to the absence of a deterioration model, trials and errors are in progress. METHODS : In this study, a deterioration model was established for bridges, which are the representative social infrastructures of roads, particularly for expansion joints that can cause enormous damage to not only the superstructure but also the substructure. The deterioration model was classified into rubber and steel, based on the material of the expansion joint. The analysis used the inspection and climate data conducted in Korea over the last 12 years. The Bayesian Markov Hazard model was applied as the analysis technique. RESULTS : The average life expectancy by type of expansion joint was analyzed to be 8.9 and 6.6 years for rubber and steel, respectively. For probabilistic life cycle cost analysis, the probability distribution of the life expectancy, validity range by confidence level, and Markov transition probability matrix were presented. CONCLUSIONS : In this study, the basis for deterministic and probabilistic life cycle cost analysis of expansion joints was laid. In future studies, it will be necessary to establish a standardized deterioration model for all types of infrastructure, including all bridge elements.

In Korea, most nuclear power plants were designed based on the design response spectrum of Regulatory Guide 1.60 of the NRC. However, in the case of earthquakes occurring in the country, the characteristics of seismic motions in Korea and the design response spectrum differed. The seismic motion in Korea had a higher spectral acceleration in the high-frequency range compared to the design response spectrum. The seismic capacity may be reduced when evaluating the seismic performance of the equipment with high-frequency earthquakes compared with what is evaluated by the design response spectrum for the equipment with a high natural frequency. Therefore, EPRI proposed the inelastic energy absorption factor for the equipment anchorage. In this study, the seismic performance of welding anchorage was evaluated by considering domestic seismic characteristics and EPRI's inelastic energy absorption factor. In order to reflect the characteristics of domestic earthquakes, the uniform hazard response spectrum (UHRS) of Uljin was used. Moreover, the seismic performance of the equipment was evaluated with a design response spectrum of R.G.1.60 and a uniform hazard response spectrum (UHRS) as seismic inputs. As a result, it was confirmed that the seismic performance of the weld anchorage could be increased when the inelastic energy absorption factor is used. Also, a comparative analysis was performed on the seismic capacity of the anchorage of equipment by the welding and the extended bolt.

Low-cost particulate matter (PM) sensors based on the light scattering principle measure the concentration of particles by the change of scattering intensity after light is irradiated onto the particles. It has been reported that when the relative humidity is high, water vapor may cause the expansion of airborne particles and affect the accuracy of the light scattering method for PM measurement, but it has also been shown that the effect of humidity is not significant or even negligible. Therefore, to determine the effect of humidity on the Plantower PMS7003 light scattering sensor, in this study, a BAM1020 (Beta Attenuation Monitoring) was installed alongside to continuously monitor the ambient atmospheric PM concentration for approximately four weeks. The sensors collected data at 10-minute intervals, resulting in a 1-hour average for comparative analysis. To accurately measure humidity, the performance of the Arduino + DHT22 humidity sensor was also pre-evaluated using a series of saturated salt solutions. The humidity was grouped into five intervals and analyzed by visual analysis. The results confirmed that there was no significant correlation between PM2.5 differences and humidity, which were randomly and uniformly distributed around the mean. However, since in the very low and high concentration ranges based on the beta-ray monitor measurements, the difference between the light scattering sensor PM10 measurement and the reference value is much larger than the difference between the PM2.5 and the reference value., there is an additional need to investigate the appropriate correction method for dust season or PM10. The results show that the outcomes of the light scattering sensor are more influenced by particle size and concentration than by humidity.

국내에서 공용중인 교량은 33,177개로 사회기반시설 중 가장 많은 비중을 차지한다. 이러한 교량은 공용하중, 온도, 습도 등에 의해 거더에 신축량이 발생하게 되고, 거더간 유간거리에 대한 안정성을 확보하기 위해 신축이음장치를 설치한다. 신 축이음장치에는 교량의 누수 및 퇴적물 낙하 등을 방지하기 위해 고무지수재를 설치하는 것이 일반적이다. 하지만 이러한 고무 지수재는 다양한 원인에 의해 쉽게 손상이 발생하게 된다. 손상된 고무지수재를 통해 거더의 부식, 교량하부 인명사고 등 다양 한 2차 피해가 발생할 수 있다. 이러한 피해를 예방하기 위해 교량의 유지관리를 수행하고 있지만 고무지수재 특성상 지속적인 교체는 불가피한 실정이다. 따라서 본 연구에서는 기존 신축이음장치에 활용되는 고무지수재의 문제점을 해결하기 위하여 초탄 성 형상기억합금을 활용한 새로운 지수재 개발 연구를 수행하였다. 초탄성 형상기억합금 지수재에 대한 유한요소해석을 수행 및 분석하였으며, 복원 효과를 통해 지속 사용 가능한 지수재 연구를 검증하였다.

본 연구에서는 칠발도, 거문도, 동해에서 20년 이상 관측된 파랑자료를 16 방위별 극치확률분석을 통해 재현빈도별 심해설 계파를 산정하였고, 이 값을 방향을 고려하지 않은 전방향파의 심해설계파와 비교하였다. Weibull 분포함수를 확률분포함수로 사용하였 으며, 최소자승법을 사용해서 매개변수를 결정하였다. 추정된 분포함수는 Kolmogorov-Smirnov 방법을 사용하여 적합도를 검증하였다. 그 결과 방향별로 구한 심해설계파가 전방향파의 심해설계파보다 모든 방향에서 상대적으로 작은 것으로 나타났다. 파향별로 구한 50년 빈도 설계파고는 칠발도, 거문도, 동해에서 각각 7.46 m(NNE), 12.05 m(S), 9.69 m(SSW)가 최대값이지만, 전방향파로 구한 설계파고는 각각 7.91 m, 13.82 m, 10.38 m이었다. 이는 현재 해양 및 연안 구조물 설계에 사용하고 있는 16 방위별 심해설계파고가 과소산정되었을 가능 성이 있음을 보여준다.

어촌뉴딜 300사업은 300개의 어촌과 어항을 대상으로 하는 복합개발사업으로 낙후된 시설 개선 및 지역특화 자원활용 등 전문 프로그램을 제공하는 사업이다. 본 연구에서는 어촌뉴딜 300사업의 선정평가 항목 별 가중치 결정을 위해 다기준 평가방법인 AHP로 전문 가 설문조사를 통한 분석을 수행하였다. 평가결과, 상위계층 평가항목은 개발여건 및 기본구상, 사업효과, 사업계획, 사업 시행 및 관리 순으로 중요도가 높게 나타났다. 사업효과 항목은 가이드라인에서 6점으로 낮은 배점이었지만, AHP 결과 15.57점의 배점이 도출되었다. 본 연구에서 도출된 항목별 가중치는 향후 어촌어항 개발사업 평가항목 배점 선정에 참조할 수 있을 것이다.

무삼투압차 역삼투압(Δπ= 0)은 KAIST H. N. Chang 명예교수가 2013년 발명, 2014년 미국 특허 출원, 2018년 특 허 취득(US 9,950,297) 해수담수화기술. Chang 등의 RO 기술은 삼투압 조정조와 저압 역삼투압의 2 챔버로 구성. Chang 등은 소금물을 비롯한 모든 수용액은 물과 용질(소금)로 완전 분리 가능 주장. 삼투압차 조정조, 저압 역삼투압조 2 챔버로 구성됨. 고농도 용액의 삼투압은 1908년 미국화학회지 출간된 MIT G. N. Lewis식 이용. 두 번째 특허(US 10,953,3367)에서 RO가 10~12 bar 저 삼투압차 수행 가능 증명. 세 번째 특허(Korea 10-2322755, 해외 출원 중) Singularity ZERO 활용하면 기존 RO 에 비해 물은 50% 추가, 막 면적은 1/3, 이론에너지는 1/5, 동일 용량의 S-ZERO 기술은 기존 RO 건설비의 50~60%로 예측됨.