해양 생물 유래 독소는 그 치명적인 유독성으로 인해 비단 인류의 건강 뿐만 아니라 양식, 어업, 해양 생태계 전반에 걸쳐 경제적 손실을 비롯한 부정적인 영향을 미친다. 하지만, 종래에 사용되던 해양 독소 검출법만으로는 이를 다 파악하여 위협을 미연에 방지하기에는 아직 부족한 실정이다. 본 논문에서는 해산물의 해양 독소 잔존 여 부를 판별하기 위해 종래에 사용되었던 시험법들의 한계를 개선하고자 각종 나노 재료 및 신규 기술들이 도입된 신속 검출법들에 대해 조사했으며, 대표적인 연구 결과들을 선정하여 사용한 나노 입자 및 전략에 대해 서술하였 다. 특히 이러한 생물 유래 독소의 검출 기술을 대중화시키고 상용화하기 위해서는, 이를 생성하는 생물군으로부터 독소를 추출하는 전처리 과정을 간소화하는 것이 매우 중요하다. 해당 문제를 해결하고자 다양한 연구에서 표적 독소와 특이적으로 결합하는 항체를 고정화한 자성 나노 입자 기반의 전처리법을 보고했으며, 더 나아가 자성 나노 입자의 촉매 특성까지 활용해 검출 감도를 높이는 다양한 연구들도 발표되었다. 또한, 기존 효소 기반의 비색 법의 검출 한계를 낮추고 검출 시스템의 안정성을 높이기 위해 양자점과 같은 형광 나노 입자를 도입하는 보고들도 있었다. 이 외에도 압타머와 나노 입자 복합체 기반의 전기화학 측정법 및 신규 기술들을 사용하고자 하는 연구들 도 보고되었다. 하지만 해양 환경의 변화에 따라 생성된 신종 독소에 대한 대처는 아직 미흡한 실정이므로, 해양 독소 유도체 또한 아울러 진단 가능한 검출 기술에 대한 후속 연구가 필요하다.

An amide group was introduced to restrain the cohesion of silica nano-particles and copolymerized with polyamic acid. Amide block copolymers were prepared using silica and (3-mercaptopropyl) trimethoxysilane (MPTMS) with a siloxane group, using 2, 6-Lutidine as a catalyst. Amide block polymers and copolymers were synthesized via ATRP after brominating pyromellitic dianhydride (PMDA) and polyamic acid of methylene diphenyl diamine (MDA) using α-bromo isobutyryl bromide. Characteristic peaks of copolymer with amide and imide groups and patterns of amorphous polymers were studied using FT-IR and XRD analyses; an analysis of the surface characteristic groups was conducted via XPS. Changes in the thermal properties were examined through DSC and TGA; solubility for solvents was also studied.

지구온난화 문제 해결을 위한 지속적인 노력과 더불어 온실가스의 국제적 배출 규제는 더욱 강화되고 있다. Non-CO2 사업단은 온실가스의 종류와 발생원에 따른 적합 기술을 선택적으로 개발함으로써 기술별 균형을 추구하고 발생원에 대한 대응방안을 모색하고 있다. 주로 화학, 전자, 자동차, 선박과 같은 수출주력산업에서 발생하므로 향후 무역규제와 연계될 경우 그 파급효과가 클 것으로 예상된다. 선택적, 집중 투자와 효율적인 관리를 통하여 우리나라 온실가스저감 목표 달성에 일조하고 수출주력산업에 도움이 될 것으로 기대한다. 본 연구는 Non-CO2 사업단개발기술, 특히 멤브레인 관련기술에 관한 토의이다. ※ 환경부 글로벌탑 환경기술개발사업 중 “Non-CO2 온실가스 저감기술개발 사업”의 지원으로 수행되었다.

4 mol% Yttria-stabilized zirconia (4YSZ) coatings with 200 μm thick are fabricated by Electron Beam Physical Vapor Deposition (EB-PVD) for thermal barrier coating (TBC). 150 μm of NiCrAlY based bond coat is prepared by conventional APS (Air Plasma Spray) method on the NiCrCoAl alloy substrate before deposition of top coating. 4 mol% YSZ top coating shows typical tetragonal phase and columnar structure due to vapor phase deposition process. The adhesion strength of coating is measured about 40 MPa. There is no delamination or cracking of coatings after thermal cyclic fatigue and shock test at 850oC.

Low temperature desorption of the used activated carbons that contain VOCs (Volatile Organic Compounds) produced from Shiwha/Banwal industrial complex were investigated. Iodine number and BET specific surface area of the activated carbons manufactured by N company in China were measured to see their characteristics prior to use in the experiment. Activated carbons were used to adsorb VOCs in a company of Shiwha/Banwal complex. Used activated carbons were collected and desorbed by the desorbing facility. After 1st adsorption and 1st desorption samples were taken for analysis. Desorbed activated carbons were reused in the same company. After 2nd adsorption and 2nd desorption samples were taken again for analysis. 4 samples were analyzed by TGA (Thermogravimetric Analyzer) at 170℃ with a heating rate of 10℃/min. Also, activation energies and reaction orders of desorption reaction were assessed by employing Friedman method and Freeman-Carroll method. The activation energies were 16.86kJ/mol by Friedman method and reaction orders were 0.36∼5.16 by Freeman-Carroll method.

To this day, conflicts have intensified between managers who want to preserve biosphere reserves and citizen who want to develop them. Based on this problem, this study seeks to investigate the establishment of a forum for communication between various stakeholders and to promote the economic development of local communities while preserving biodiversity. First, in terms of conservation, the results indicated that Gyeonggi Province and Namyangju City highly valued direct conservation activities in biosphere reserves, whereas Pocheon and Uijeongbu City highly valued indirect conservation functions through management or monitoring. Second, in terms of development, it was found that there were differences in the roles, perceptions and responsibilities with respect to biosphere reserves among the different layers of government: the central government agency, the Cultural Heritage Administration, the metropolitan government, Gyeonggi-do, and the local governments, Pocheon, Namyangju, and Uijeongbu. Third, in terms of logistical support, which serves as a function for communication and practical participation among management entities, the results suggested that it was necessary to establish a comprehensive decision-making organization for efficient management and operation and to provide opportunities for active participation. The study can be utilized as a basic reference for developing efficient communication by management entities in protected areas with similar challenges.

This study aimed to investigate the effects of dietary Ptecticus tenebrifer on the fecal microbiomes of bichon frise. A total of 16 bichon frise dogs (average weight, 2 kg) were randomly allotted to 4 dietary treatments (4 dogs/group): general pet food, two types of domestic pet food containing Ptecticus tenebrifer, and one imported pet food containing Ptecticus tenebrifer. In the controls, Firmicutes accounted for the highest proportion (82%) at the phylum level in the fecal microbiomes. The Tax4Fun2's functional prediction program indicated that the control groups showed a relatively high amount of obesity-related microorganisms; the pathways included three types of carbohydrate metabolism. Among the treatments, Firmicutes abundances was the least in the treatments with the two types of domestic pet food containing Ptecticus tenebrifer; this did not affect the functional prediction of Tax4Fun2. In conclusion, the two types of domestic feed with Ptecticus tenebrifer were healthy and suitable for bichon frise; they could be beneficial in terms of obesity.

Multi-Walled Carbon Nanotubes (MWCNTs) were modified with epoxy and aminosilane diethanolamine (DEA), and nanocomposites of poly(butylene adipate-co-terephthalate) (PBAT) and the modified MWCNTs were prepared with the aim of improving the physical properties of biodegradable PBAT. The physical and the thermal properties of the PBAT/MWCNT nanocomposites were investigated using various techniques. Fourier transform infrared spectroscopy measurements revealed that the MWCNTs were efficiently modified with DEA. Scanning electron micrographs of the nanocomposites indicated that the modified MWCNTs were dispersed homogeneously in PBAT. The thermal stability of the nanocomposite decreased with increase in the content of epoxy-MWCNT-DEA due to the poor thermal stabilities of epoxy and amino silane DEA. However, the surface hydrophobicity of the nanocomposite increased. The highest stress (170% of PBAT) was observed when the content of epoxy-MWCNT-DEA in the nanocomposite was 2 wt%.

The consumption of waxy corn is steadily increasing in Korea. Waxy corn is harvested before it reaches full maturity and consumed immediately or follwing cold storage. Glutinous and sweet kernels are preferred due to their high palatability. The kernel properties can change rapidly following harvest, and, therefore, optimal conditions to maintain the kernel quality of corn should be identified. In addition, the timing of harvest of waxy corn ear should be also determined for optimal marketable corn production. From 10 days after silking (DAS) to25 DAS. fresh ear weight and single kernel weight rapidly increased from 78.3 g and 1.13 g, respectively, to 224.9 and 3.61 g, respectively. However, by 30 DAS both fresh and single kernel weight decreased by 10.6% and 6.1%, respectively. Kernel hardness significantly increased up to 25 DAS, and a further slight increase in kernel hardness was observed at 30 DAS. Total sugar content in kernel decreased from 12.5% at 10 DAS to 3.5% at 35 DAS, which was the result of the conversion of sugars to starch during ear development. Crude protein content in kernel did not vary significantly in comparison to kernel hardness. During storage of ear, kernel hardness increased from 726 g cm-2 at harvest to 1,894 g cm-2 following 28 days of storage at a low temperature (0°C). Kernel hardness increased 2.5 fold from 15 DAS to 30 DAS. Soluble protein level in kernel increased until 10 DAS, following which a slight decrease was observed. The soluble protein content decreased from 1.85% at 5 DAS to 1.45% at 35 DAS. Total sugar content in kernel decreased regardless of storage temperature; however, the rate of reduction was lower at 0°C than that observed following storage at 4°C and 10°C. The rate of reduction in kernel moisture content was also lower at 0°C than that observed at 4°C and 10°C.

현재 국내외에서 제공되고 있는 기후변화 시나리오 자료의 경우 일단위로 제공되고 있다. 그러나 수문 설계 및 계획 시 중요한 입력자료 중 하나 는 시간단위 강우 자료로서 기후변화 시나리오에 따른 수자원 변동성을 평가하기 위해선 신뢰성 있는 상세화 기법이 필요하다. 국내외에서는 일단 위에서 일단위로 상세화 하는 기법, 또는 공간상세화 기법 연구는 다수 진행된바 있는 반면, 시간단위 상세화 기법 연구는 일단위 연구에 비해 상대 적으로 미진한 실정이다. 이러한 점에서 본 연구에서는 기후변화 시나리오에 따른 영향 평가가 가능한 자료생성을 위해 Conditional Copula 모형 을 활용하여 극치시간단위 강우량 상세화 기법을 개발하였으며, 미래 RCP 8.5 시나리오를 활용하여 연대별 극치시간강우량을 생성하였다. 생성 된 결과는 우리나라 기상청 지점별로 빈도해석을 통해 결과를 제시하였으며, 본 연구결과는 수자원 분야에서 미래 기후변화 영향을 평가하기 위한 기초자료로 활용 될 수 있을 것으로 기대된다.

최근 들어 FRP 판을 영구 거푸집 및 주요 인장보강재로 활용하기 위한 새로운 콘크리트 교량 바닥판 시스템 개발에 대한 연구가 활발히 진행되고 있다. 영구거푸집과 인장 보강재로의 병행이용은 기존의 콘크리트 바닥판 보다 공사비와 공사기간을 절감 할 수 있다. 본연구에서 는 영구거푸집 및 주요인장재로 활용한 FRP 판의 종류에 따른 현장타설 콘크리트와 부착응력에 대해 실험을 수행하였다. 부착성능 평가를 실시하였고, 부착특성을 나타내는 중요한 변수중에 하나로서 부착 강도 및 부착면의 파괴 매커니즘 특성을 알 수 있는 계면 파괴에너지를 나타내었다. 일반콘크리트에서 계면 파괴에너지는 GF11의 경우 0.24kN/m이고, GF21의 경우에는 0.43kN/m, GF31과 CF11의 경우에는 각각 0.46kN/m와 0.44kN/m로 나타났고, RFCON에서는 GF12의 경우 0.52kN/m, GF22와 CF12에서는 각각 0.36kN/m와 0.51kN/m로 나타났다.

Sustainable and eco-friendly polymers, natural polymers, bio-based polymers, and degradable polyesters, are of growing interest because of environmental concerns associated with waste plastics and emissions of carbon dioxide from preparation of petroleum-based polymers. Degradable polymers, poly(butylene adipate-co-terephthalate) (PBAT), poly(propylene carbonate) (PPC), and poly(L-lactic acid) (PLLA), are related to reduction of carbon dioxide in processing. To improve a weak mechanical property of a degradable polymer, a blending method is widely used. This study was forced on the component separation of degradable polymer blends for effective recycling. The melt-mixed blend films in a specific solvent were separated by two layers. Each layer was analysed by FT-IR, DSC, and contact angle measurements. The results showed that each component in the PPC/PLLA and PPC/PBAT blends was successfully separated by a solvent.

In this experiment no solvent based polyurethane(PU) adhesives were prepared with the polyol, isocyanate, dioctyl phthalate(DOP), 2-hydroxyethylacrylate(2-HEA) and other acrylate monomers. The softenening point of the PU adhesives measured by Ring & Ball method were examined in the present study. And adhesion strength and mechanical properties such as tensile strength and 100% modulus of the PU adhesives were evaluated by Universal Test Machine. The experimental results showed that increase of both DPE-41, benzoylperoxide(BPO) and toluene diisocyanate(TDI) increased softenening point, adhesion strength, tensile strength and 100% modulus. However as DOP content increased sofenening point, adhesion strength decreased and tensile strength, 100% modulus also decreased.

To complement the general concrete, DFRCC(Ductile Fiber Reinforced Cementitious Composites) has recently received attention. An experimental study for bond slip behavior of cast-in-place DFRCC and a pultruded FRP(Fiber Reinforced Polymer) plank was used as the both permanent formwork and the tensile reinforcement for a concrete structural member is described in this paper. This study focuses on investigation of the bond capacity of sand coated interface between FRP and cast-in-place DFRCC experimentally.

With the incorporation of hydrogen peroxide(H2O2) and NaLS as an initiator and emulsifier, acrylic acid monomer was graft copolymerized with sodium alginate prepared from alginic acid, and then the grafted copolymer was confirmed through IR spectrometer. When the amounts of acrylic acid increased the grafting also showed increasing trend. While the contents of hydrogen peroxide was varied in the aqueous sodium alginate solution, the grafting efficiency decreased gradually as the amounts of initiator increased.

Fibers of microbial polyesters, poly(3-hydroxy butyrate) (PHB) and poly(3-hydroxy butyrate-co-3-hydroxy valerate) (HB-co-HV) were prepared by electrospinning method. The obtained fibers were evaluated by differential scanning calorimetry, scanning electron microscopy, and oil absorption. The formation of fibers was strongly dependent on a concentration of solution. At a low concentration, the fibers contained beads which is from aggregation of polymer due to short evaporation time. The fine fibers with 2-5 mm diameter were obtained at 20 wt% concentration. The contact angle measurement showed that the fiber had higher water contact angle than the film due to the lotus-like effect. Oil absorbency showed that the fiber had higher than the film. Specially, the HB-co-HV fiber which was spinned from 20 wt% absorbed 65% oil which is much higher than that of a normal polypropylene-based oil paper.