The bi-materials with Al-Mg alloy and its composites reinforced with SiC and particles were prepared by conventional powder metallurgy method. The A1-5 wt%Mg and composite mixtures were compacted under , and then the mixtures compacted under 400 MPa were sintered at for 5h. The obtained bi-materials with Al-Mg/SiCp composite showed the higher relative density than those with composite after compaction and sintering. Based on the results, the bi-materials compacted under 400 MPa and sintered at 873K for 5h were used for mechanical tests. In the composite side of bi-materials, the SiC particles were densely distributed compared to the particles. The bi-materials with Al-Mg/SiC composite showed the higher micro-hardness than those with composite. The mechanical properties were evaluated by the compressive test. The bi-materials revealed almost the same value of 0.2% proof stress with Al-Mg alloy. Their compressive strength was lower than that of Al-Mg alloy. Moreover, impact absorbed energy of bi-materials was smaller than that of composite. However, the bi-materials with Al-Mg/SiCp composite particularly showed almost similar impact absorbed energy to composite. From the observation of microstructure, it was deduced that the bi-materials was preferentially fractured through micro-interface between matrix and composite in the vicinity of macro-interface.

BaTiO3 powders were prepared by sol-gel method from different concentration of KOH aqueous solution and Ba/Ti molar ratio. Particle shape, size and crystal structure of prepared BaTiO3 powders were analyzed by SEM, XRD, and FT-IR. As the result of KOH concentration changing, spherical particles were obtained by condition more than 3 M and particle size decreased as concentration increasing. Different appearance showed between dried and sintered powders against changing of Ba/Ti molar ratio. In case of dried powders, the crystallinity decreased as molar ratio increasing. On the other hand, increased as molar ratio increasing in case of sintered powders.

In T-mixer crystallization, supersaturation is generated by mixing of another solvent or non-solvent in order to reduce the solubility of the compound. Also, T-mixer is a type of continuous crystallization. In order to induce micro-mixing, two solutions were mixed rapidly by T-mixer, which formed high supersaturation. As the results, mean size of HMX crystals decreased with increasing de-supersaturation rate (Rs). Eventually, HMX particles ranging from 0.5 to 5μm can be obtained by T-mixer crystallization. Mixing efficiency in T-mixer increased with increasing Rs values. In T-mixer crystallization without surfactants, homogeneous nucleation was formed when S and Rs was over 54 and 1.6×103/sec. In T-mixer crystallization with surfactants, homogeneous nucleation was formed when S and Rs was over 26 and 7.4/sec.

The electrophoretic deposition process of Ni nano-particles in organic suspension was employed for self-repairing of heat exchanger tubes. For this purpose, Ni nano-particles prepared by levitational gas condensation method were dispersed into the solution of ethanol with the addition of dispersant Hypermer KD2. For electrophoretic deposition of Ni nano-particles on the Ni alloy specimen, constant electric fields of 20 and 100 V were applied to the specimen in Ni-dispersed solution. It was found that as electrophoretic deposition proceeds, the size of the pit or crack remarkably decreased due to the agglomeration of Ni nano-particles at the pit or crack. This strongly suggests that the electrophoretic mobility of the charged particles is larger for the damaged part with a higher current value rather than outer surfaces with a lower current value.

The aim of this paper is to analyze Korean specific particles ‘i/ga’ and ‘eul/leul’ and show how to teach them effectively to foreign learners. In this respect, we first analysed some typical ‘i/ga’ or ‘eul/leul’ constructions: they seem very similar in appearance but their syntactic structures are quite different. We showed that in order to explain effectively ‘i/ga’ and ‘eul/leul’ constructions, the notion of ‘topic’ should be introduced and found that there exist some particular semantic restrictions between two successive noun phrases participating in ‘i/ga’ and ‘eul/leul’ constructions. Secondly, we tried to show how to construct the educational substance and method of these specific particles ‘i/ga’ and ‘eul/leul’. We proposed to introduce types of ‘i/ga’ and ‘eul/leul’ constructions, typical predicates used with these constructions, semantic restrictions of two successive noun phrases participating in these constructions, equivalent constructions corresponding to these constructions and their concrete examples in constructing the educational substance and method of the specific particles ‘i/ga’ and ‘eul/leul’.

In this work, the dispersion behavior of particles in binary aluminum (Al)-copper (Cu) cast alloy was investigated with respect to Cu contents of 20 (hypoeutertic), 33 (eutectic) and 40 (hypereutectic) wt.%. In cases of hypo and hypereutectic compositions, SEM images revealed that the primary Al and phases were grown up at the beginning, respectively, and thereafter the eutectic phase was solidified. In addition, it was found that some of particles can be dispersed into the primary Al phase, but none of them are is observed inside the primary 6 phase. This different dispersion behavior of particles is probably due to the difference in the val- ues of specific gravity between particles and primary phases. At eutectic composition, particles were well dispersed in the matrix since there is few primary phases acting as an impediment site for particle dispersion during solidification. Based on the experimental results, it is concluded that particles are mostly dispersed into the eutectic phase in binary Al-Cu alloy system.

The magnetic alloys of Cu-Fe () were prepared by a mechanical alloying method and their structural and magnetic behaviors were examined by X-ray diffraction and Mossbauer spectra. The magnetization curves did not distinctly show the saturation at 70 kOe for the concentrated alloys of . The Mossbauer spectrum of at room temperature shows one Lorentzian line of the paramagnetic phase, whereas the Mossbauer spectrum of consists of sextet Lorentzian line at room temperature and a centered doublet line. The Mossbauer spectra of measured in the temperature ranges from 13 to 295 K, implies that to consists of two magnetic phases. One superimposed sextet corresponds to the ferromagnetic iron in Cu and the other one indicates the superparamagnetic iron rich phase.

색소변이체에서 버섯 바이러스의 게놈인 dsRNA가 확인 되었으며, 크기는 각각 5.8kb, 1.8kb 이었다. 느타리바이러스 진단용 프라이머인 PVP로 RT-PCR을 수행한 결과 500bp 크기의 특이밴드가 관찰되었다. 또한 양송이 바이러스 진단용 프라이머 LIVP와 MBVP에서도 특이밴드가 관찰되었으나 양송이 바이러스와는 다른 양상이었다. 원형느타리의 백색변이체 (MGL2205)에 존재하는 바이러스유사입자는 구형이었으며, 크기는 14, 20∼45nm이었다. 균사체의 세포단면을 관찰한 결과 바이러스 순화액에서 확인된 바이러스유사입자와 비슷한 구형의 입자들이 관찰되었으며, 순화된 바이러스와 동일한 입자인지는 추후 확인되어야 할 것으로 사료된다. 원형느타리 백색변이체(MGL2205)에 존재하는 바이러스의 최적 증식 조건은 15℃, pH 6, 배양기간 3주인 것으로 판단되며, 이 결과는 이와 유사한 재배적 조건에서 재확인되어야 할 것으로 사료된다.

The microstructure and mechanical properties of hot-pressed composites with a different sintering temperature have been studied. The size of matrix grain and Cu dispersion in composites increased with increase in sintering temperature. Fracture toughness of the composite sintered at high temperature exhibited an enhanced value. The toughness increase was explained by the thermal residual stress, crack bridging and crack branching by the formation of microcrack. The nanocomposite, hot-pressed at , showed the maximum fracture strength of 707 MPa. The strengthening was mainly attributed to the refinement of matrix grains and the increased toughness.

The electrophoretic deposition process of Ni nano-particles was employed for self-repairing of heat exchanger tubes. For electrophoretic deposition of Ni nano-particles on pitted Ni alloy specimen, a constant electric field of 100 V was applied to the specimen for 180 s in Ni-dispersed solution. It was found that as electrophoretic deposition proceeded, the size of the pit remarkably decreased due to the agglomeration of Ni nano-particles at the pit. This strongly suggests that the electrophoretic mobility of the charged particles is larger for the pit with a higher current value rather than outer surfaces with a lower current value.

The paper presents the possibilities of obtaining new composite materials based on sintered porous ceramics with particles and fibre of infiltrated by aluminum alloy. The EN AC - AlSi12 alloy features the matrix material, whereas the RF50AX-301 preform, of Saffil Automotive, was used as the reinforcement. Examinations of ceramics preforms permeability were made. Metallographic examination of composite materials made on light microscope and in scanning electron microscope show that aluminum alloys fill micropores in the matrix. New composite materials show twice higher value of hardness in comparison with matrix. Results indicate that it is possible to infiltrate porous ceramic with liquid aluminum alloy to obtain new composite materials were advantageous properties of each component are connected.

Particulate reinforced titanium composites were produced by PM rout. Differents volumetric percentages of TiN reinforcements were used, 5,10,15 vol%. Samples were uniaxial pressed and vacuum sintered at differents temperatures between . Density, porosity, shrinkage, mechanical properties and microstructure were studied. Elastic properties and strength resistance were analysed by flexural strength and tension tests, and after the test, fractured samples were analysed too, obtaining a correlation between the fracture, interparticulated or intraparticulated, and the reinforcement addition.. Hardness and microhardness test were applied too, in order to complete the study about mechanical properties. In order to study wear resistance pin-on-disc test were used. In addition, the temperature influence, the reactivity between matrix and reinforcement, and the microstructures developed were observed by optical and electron microscopy.

We newly designed and manufactured a new arranging system for a three-dimensional artificial crystal of monosized micro particles. In this system, a robotic micro-manipulator accurately locates the spherical particle onto the lattice point, and subsequently fiber lasers micro-weld the contact points between the neighboring particles. Actually, one- and two-dimensional arrays were constructed using monosized tin particles with the diameter of 400 m. Moreover, due to optimization of the process parameters, we successfully constructed the artificial crystals of simple cubic and diamond structures. In particular, the diamond structure which can represent a large photonic band gap is expected to progress toward a practical photonic crystal device.