PURPOSES : The purpose of this study is to analyze not only the strength but also the durability and abrasion resistance of concrete pavements as increasing the cases of domestic concrete pavement damage which do not meet the service years. METHODS: The bottom layer of a two-lift concrete pavement was paved with original Portland cement (OPC) with 20~23 cm thickness. On the other hand, the top-layer, which is directly exposed to the environment and vehicles, was paved with high-performance concrete (HPC) with 7~10 cm thickness. For the optimal mixed design of the top-layer material of a two-lift concrete pavement, silica fume and polymer powder were mixed. Furthermore, it analyzes abrasion resistance of concrete as follow‘ ASTM C 779’which is dressing wheel abrasion test method. RESULTS : As a result, abrasion resistance is improved with increasing the silica fume ratio. When the polymer powder is mixed, abrasion resistance of concrete is much improved. However, the effect of mixing ratio is not significant. It is very effective that adding both silica fume and polymer powder occur 20~40% of abrasion comparing with OPC variables. CONCLUSIONS : The concrete strength and durability increased with silica fume and polymer powder. In particular, it is significant increasing strength of polymer powder under the flexural strength. In the abrasion resistance side, it is also significant when the silica fume and polymer powder used together.

The effects of chemical compositions (protein, lipid, and dietary fiber) on the physical properties of dried biji powders were investigated. The raw biji was freeze-dried (control) and hot-air dried (untreated). The untreated biji was further defatted and deproteinated. The prepared biji powders were analyzed for the proximate composition, total dietary fiber (TDF), water absorption index (WAI), water solubility index (WSI), swelling power, solubility (including the quantification of soluble carbohydrate and protein fractions), and final viscosity (using a rapid visco analyzer). Control and untreated biji powders exhibited the similar chemical compositions. The defatted biji possessed higher TDF, although its protein content did not significantly differ for control and untreated ones. The deproteinated biji consisted mainly of TDF. WAI and swelling power increased in the order: deproteinated > defatted > control > untreated biji powders. WSI and solubility increased in the order: control > untreated > defatted > deproteinated biji powders. The similar patterns were observed for soluble carbohydrate and protein fractions. The deproteinated biji revealed the highest viscosity over applied temperatures, while the untreated one was lowest. Overall results suggested that the physical properties of the dried biji powder were reduced by protein and fat, but enhanced by dietary fiber.

ZnO crystals with different morphologies are synthesized through thermal evaporation of the mixture of Zn and Cu powder in air at atmospheric pressure. ZnO crystals with wire shape are synthesized when the process is performed at 1,000 oC, while tetrapod-shaped ZnO crystals begin to form at 1,100 oC. The wire-shaped ZnO crystals form even at 1,000 oC, indicating that Cu acts as a reducing agent. As the temperature increases to 1,200 oC, a large quantity of tetrapod-shaped ZnO crystals form and their size also increases. In addition to the tetrapods, rod-shaped ZnO crystals are observed. The atomic ratio of Zn and O in the ZnO crystals is approximately 1:1 with an increasing process temperature from 1,000 oC to 1,200 oC. For the ZnO crystals synthesized at 1,000 oC, no luminescence spectrum is observed. A weak visible luminescence is detected for the ZnO crystals prepared at 1,100 oC. Ultraviolet and visible luminescence peaks with strong intensities are observed in the luminescence spectrum of the ZnO crystals formed at 1,200 oC.

This study evaluated the quality characteristics of rice cookies prepared with different amounts (0, 3, 6, 9%) of hibiscus powder. The pH of cookie dough decreased as the amount of hibiscus powder increased. Additionally, the moisture content and spread factor were higher in groups containing hibiscus powder than in the control groups. Furthermore, the L-value decreased with increasing hibiscus powder, while the a-value increased. The incorporation of hibiscus powder into cookies decreased hardness. Additionally, consumer acceptance testing revealed that the addition of up to 6% hibiscus powder was desirable in terms of overall acceptability. The total phenol content of the control groups was 12.32 mg GAE/100 g, while the levels in the groups containing hibiscus powder ranged from 23.32 to 59.86 mg GAE/100 g. Finally, DPPH and ABTS radical scavenging activity increased with increasing hibiscus powder level. Taken together, the results of this study indicate that amending cookies with 6% hibiscus powder can improve antioxidant activities without affecting sensory quality.

Porous metals demonstrate not only excessively low densities, but also novel physical, thermal, mechanical, electrical, and acoustic properties. Thus, porous metals exhibit exceptional performance, which are useful for diesel particulate filters, heat exchangers, and noise absorbers. In this study, SUS316L foam with 90% porosity and 3,000 μm pore size is successfully manufactured using the electrostatic powder coating (ESPC) process. The mean size of SUS316L powders is approximately 12.33 μm. The pore properties are evaluated using SEM and Archimedes. As the quantity of powder coating increases, pore size decreases from 2,881 to 1,356 μm. Moreover, the strut thickness and apparent density increase from 423.7 to 898.3 μm and from 0.278 to 0.840 g/cm3, respectively. It demonstrates that pore properties of SUS316L powder porous metal are controllable by template type and quantity of powder coating.

Metallic tantalum powder is manufactured by reducing tantalum oxide (Ta2O5) with magnesium gas at 1,073–1,223 K in a reactor under argon gas. The high thermodynamic stability of magnesium oxide makes the reduction reaction from tantalum oxide into tantalum powder possible. The microstructure after the reduction reaction has the form of a mixture of tantalum and magnesium oxide, and the latter could be entirely eliminated by dissolving in weak hydrochloric acid. The powder size in SEM microstructure for the tantalum powder increases after acid leaching in the range of 50–300 nm, and its internal crystallite sizes are observed to be 11.5 to 24.7 nm with increasing reduction temperatures. Moreover, the optimized reduction temperature is found to be 1,173 K as the minimum oxygen concentration is approximately 1.3 wt.%.

Nanoparticles of PbTe are prepared via chemical reaction of the equimolar aqueous solutions of Pb(CH3COO)2 and Te at 120°C. The size of the obtained particles is 100 nm after calcination in a hydrogen atmosphere. Dense specimens for the thermoelectric characterization are produced by spark plasma sintering of prepared powders at 400°C to 500°C under 80 MPa for 5 min. The relative densities of the prepared specimens reach approximately 97% and are identified as cubic based on X-ray diffraction analyses. The thermoelectric properties are evaluated between 100°C and 300°C via electrical conductivity, Seebeck coefficient, and thermal conductivity. Compared with PbTe ingot, the reduction of the thermal conductivities by more than 30% is verified via phonon scattering at the grain boundaries, which thus contributes to the increase in the figure of merit.

Krill (Euphausia superba) 분말이 Sprague Dawley계 수컷 흰쥐 혈청 중 non-esterified fatty acid(NEFA), blood urea nitrogen (BUN), creatinine, uric acid 및 전해질 농도에 미치는 영향을 조사하기 위하여 기본식이를 급여한 대조군인 BG군과 기본식이에 NaF 10 mg 경구 투여한 BFG군을 비롯하여 10%, 20%, 30%의 krill 분말을 첨가한 식이에 NaF 10 mg 경구 투여한 KMF10군, KMF20군, KMF30군, 5가지의 급여군으로 나누어 5주간 사육한 결과, 흰쥐의 NEFA와 BUN, creatinine 농도는 krill 분말 급여군인 KMF10군, KMF20군, KMF30군에서 BFG군보다 유의적으로 감소한 결과가 관찰되었으며, uric acid 농도에서 KMF10군은 BFG군과 유의적 차이가 없었으나, KMF20군과 KMF30군에서 유의적으로 감소하였다(p<0.05). 또한 전해질 농도에서 총 칼슘(T-Ca)은 군간의 유의적 차이가 없는 것으로 관찰되었지만 krill 분말 함량에 따라 증가하였으며(p<0.05), 인(Pi) 농도는 krill meal 함량에 따른 변화는 없는 것으로 나타났다. 따라서, krill 분말은 NEFA 및 BUN, creatinine, uric acid 농도 개선에 효과가 있을 것으로 사료된다.

인삼과립차의 편의성 및 기호성 증진을 위해 부형제인 젖당, 포도당 및 아라비안 검의 첨가량에 따른 과립차의 물리적 특성을 분석하였다. 젖당의 첨가량이 증가할수록, 포도당의 첨가량이 감소할수록 흡습성은 낮아지고 용해성은 증가하는 경향을 보였다. 사포닌 용출량은 첨가되는 부형제의 종류 및 양에 영향을 받기 보다는 인삼농축액의 첨가량에 더 큰 영향을 받는 것으로 나타났다. 아라비아 검의 첨가량이 증가할수록 흡습성, 용해성은 증가하는 경향을 보였고, 색도는 큰 차이점이 없었다. 부형제 첨가에 따른 인삼 과립차의 최적 배합비는 인삼농축액 10%, 젖당 80%, 글루코즈 5% 그리고 아라비아 검의 함량이 5% 이었다.

W-10 wt% Ti alloys that have a homogeneous microstructure are prepared by thermal decomposition of WO3-TiH2 powder mixtures and spark plasma sintering. The reduction and dehydrogenation behavior of WO3 and TiH2 are analyzed by temperature programmed reduction and a thermogravimetric method, respectively. The X-ray diffraction analysis of the powder mixture, heat-treated in an argon atmosphere, shows W- oxides and TiO2 peaks. Conversely, the powder mixtures heated in a hydrogen atmosphere are composed of W, WO2 and TiO2 phases at 600 ℃ and W and W-rich β phases at 800 ℃. The densified specimen by spark plasma sintering at 1500 ℃ in a vacuum using hydrogen-reduced WO3-TiH2 powder mixtures shows a Vickers hardness value of 4.6 GPa and a homogeneous microstructure with pure W, β and Ti phases. The phase evolution dependent on the atmosphere and temperature is explained by the thermal decomposition and reaction behavior of WO3 and TiH2.

Additive manufacturing by electron beam melting is an affordable process for fabricating near net shaped parts of titanium and its alloys. 3D additive-manufactured parts have various kinds of voids, lack of fusion, etc., and they may affect crack initiation and propagation. Post process is necessary to eliminate or minimize these defects. Hot isostatic pressing (HIP) is the main method, which is expensive. The objective of this paper is to achieve an optimum and simple post heat treatment process without the HIP process. Various post heat treatments are conducted for the 3Dprinted Ti-6Al-4V specimen below and above the beta transus temperature (996oC). The as-fabricated EBM Ti-6Al-4V alloy has an α‘-martensite structure and transforms into the α+β duplex phase during the post heat treatment. The fatigue strength of the as-fabricated specimen is 400 MPa. The post heat treatment at 1000oC/30 min/AC increases the fatigue strength to 420 MPa. By post heat treatment, the interior pore size and the pore volume fraction are reduced and this can increase the fatigue limit.

The hydrogen reduction behavior of MoO3-CuO powder mixture for the synthesis of homogeneous Mo-20 wt% Cu composite powder is investigated. The reduction behavior of ball-milled powder mixture is analyzed by XRD and temperature programmed reduction method at various heating rates in Ar-10% H2 atmosphere. The XRD analysis of the heat-treated powder at 300oC shows Cu, MoO3, and Cu2MoO5 phases. In contrast, the powder mixture heated at 400oC is composed of Cu and MoO2 phases. The hydrogen reduction kinetic is evaluated by the amount of peak shift with heating rates. The activation energies for the reduction, estimated by the slope of the Kissinger plot, are measured as 112.2 kJ/mol and 65.2 kJ/mol, depending on the reduction steps from CuO to Cu and from MoO3 to MoO2, respectively. The measured activation energy for the reduction of MoO3 is explained by the effect of pre-reduced Cu particles. The powder mixture, hydrogen-reduced at 700oC, shows the dispersion of nano-sized Cu agglomerates on the surface of Mo powders.

In the present work, we synthesize nano-sized ZnO, SnO2, and TiO2 powders by hydrothermal reaction using metal chlorides. We also examine the energy-storage characteristics of the resulting materials to evaluate the potential application of these powders to dye-sensitized solar cells. The control of processing parameters such as pressure, temperature, and the concentration of aqueous solution results in the formation of a variety of powder morphologies with different sizes. Nano-rod, nano-flower, and spherical powders are easily formed with the present method. Heat treatment after the hydrothermal reaction usually increases the size of the powder. At temperatures above 1000oC, a complete collapse of the shape occurs. With regard to the capacity of DSSC materials, the hydrothermally synthesized TiO2 results in the highest current density of 9.1 mA/cm² among the examined oxides. This is attributed to the fine particle size and morphology with large specific surface area.