The reinforced retaining wall was introduced in the late 1980s and has been actively used since the 1990s in Korea 's expressway construction. At the beginning of the introduction, proper stiffeners and backfill materials were used and compaction management was thoroughly carried out, which was recognized as an economical and excellent workability method. However, the current understanding of reinforced earth retaining walls about 30 years old is a negative image such as inadequate reinforcement materials, backfill materials, insufficient compaction, and insufficient drainage system. In this way, the reinforced earth retaining walls that have been constructed in the midst of the negative perception are about 1,000 at the expressway site, and about 1000 will be completed in a few years and about 2,000 will be used. Most of the problems of reinforced earth retaining wall were found during maintenance, and countermeasures are suggested by tracing back to what problems were observed in the design and construction of the observed phenomena. The retaining walls to be installed in future maintenance should be minimized in designing and constructing to prevent problems. It is estimated that such a problem can be solved by changing the recognition. Therefore, in this study, damage cases of reinforcement retaining wall which is frequently occurred in the expressway of Korea were analyzed to derive the preventive maintenance method of reinforced earth retaining walls. Then, the problems and countermeasures were analyzed for each type of damage.

In Sri Lanka, the shoulder in asphalt pavements has been constructed using the materials transported from borrow pit in the iRoad Project due to the low quality of in-situ soils. After excavating 150~200mm thick and 500mm wide shoulder area, the borrow pit materials are placed and compacted according to specifications. The excavated in-situ soils are dumped in designated location. It is estimated that this process of shoulder construction is not economical due to high material transportation cost and can also induce the environmental issues by disposal of in-situ soils. It can also cause distresses such as surface rutting and edge drop-off in soft shoulder section due to bearing capacity failure and off-tracking of vehicle. The heavy rainfall in Sri Lanka can induce severe erosion problem when using the soft shoulder. To improve the strength and durability of pavement shoulders in the iRoad Project, the soil stabilization will be a good alternative to solve the above mentioned problems. The use of in-situ soils with addition of soil stabilizer enables to reduce the construction cost of shoulder section and mitigate the environment issues. The objective of this task is to review the application of soil stabilization method for soft shoulder construction in the iRoad Project. Firstly, the quantitative analysis of soil strength improvement due to soil stabilization was done for soil samples collected from iRoad construction sites. Two types of soils were selected from iRoad Project sites and prepared for soil stabilization testing by the Road Development Authority. Secondly, the appropriate stabilizer was selected at given soil type based on test results. Three different stabilizers, ST-1, ST-2, and ST-3, produced in Korea were used for estimating soil strength improvements. Finally, the optimum stabilizer content was determined for improving shoulder performance. The uniaxial compressive strength (UCS) test was conducted to evaluate the strength of stabilized soil samples in accordance with ASTM D 1633. The use of bottom ash as a stabilizer produced from power plant in Sri Lanka was also reviewed in this task.

This paper evaluates the affection of steel slag in the asphalt mixtures for the self-healing purpose through microwave heating technique. Four different contents of steel wool fibers (SWF) were developed in hot mix asphalt and two types of aggregate were used: steel slag aggregate and normal aggregate. By using the infrared camera, the thermal distribution, as well as the optimum healing time of test samples, were recorded. All mixtures were evaluated their healing performance throughout 8 cycles. The substitution of about 30% normal coarse aggregate by steel slag is prominent due to its effect not only produces better healing performance but also enhances the whole mixture improve load-displacement trend with higher ductile behavior. The application of steel slag in HMA is a promising method which contributes toward the sustainable roadway development.

This research was conducted to elucidate the optimum conditions for the antibacterial activity of konjak jelly using the evolutionary operation-factorial design technique. In the first set of experiments, concentration of a coagulation agent, soaking liquid, and temperature of water were set to 0.4%, 0.6×10－2 N, and 65℃ as a central point, respectively. The highest antibacterial activity was acquired at E21, in which the number of bacteria was 1.25 log cfu/g. Because the code of changes in the main effect was (-), it could be decided that the central point of the first set was not the optimum point. Although antibacterial activity in the second set was improved, the values of the main effect were higher than that of changes in the mean effect. The central point of third set was concentration of coagulation agent 0.8%, concentration of soaking liquid 1.0×10－2 N, and temperature of water 65℃. It was found that the antibacterial activity of central point in the third set was highest among all the tested set. Further, all the necessary conditions were appropriate to reach the optimum condition. The antibacterial activity of the central point in third set was more than 1,000 times higher than that of E11, in first set.

Magnetic resonance imaging (MRI) technique has recently been applied in agriculture and food science. It has potential to visualize internal structure of foods in nondestructive way and provides spatial information which could make reconstruct of three-dimension. MRI system also has great advantage for tracking water in beans or seeds. This study intends to analyze the changes of water distribution of coffee beans during water up-taking process. Samples used in the experiment were ‘Robusta’ coffee beans (Vietnam G1, Scr18 polish). A 30mm diameter plastic disposable test tube was used to hold bean during water up-take process. The oil column was placed next to the tube to get and to use as a reference signal. The magnetic resonance imaging system which installed at Institution for Agricultural Machinery & ICT Convergence in Chonbuk National University was used to obtain magnetic resonance (MR) image data sets. 30 images are included in each image data sets with ‘Axial’ image plane direction. In experiment, we used ‘Gradient Echo 3D’ pulse sequence. The water uptake process was performed for 150 minutes and acquired image data sets in every 10 minutes. This study showed some coffee beans which extracted as region of interest (ROI) from each images to study the water uptake process.

목 적：New fast acquisition technique인 wave-CAIPIRINHA를 적용한 MPRAGE sequence를 통해 brain 의 국소병변 진단능과 화질의 변화를 알아보고자 한다. 대상 및 방법：2017년 11월 22일부터 2018년 1월 2일까지 뇌 백질 병변이 있어 본원에서 추적 검사 중인 환자 39명(남자 21명, 여자 18명, 평균연령 54.9세)을 대상으로 conventional 3D T1 MPRAGE와 wave- CAIPI R(reduction factor) 6(3 × 2), wave-CAIPI R(reduction factor) 4(2 × 2) 기법으로 영상을 획득하였다. 전신용 3.0T MRI(Skyra, SIEMENS, Erlangen, Germany), 64 channel head coil을 사 용하였고, 모든 sequence는 sagittal로 촬영하였으며 interpolation은 적용하지 않았다. Conventional 3D T1 MPRAGE의 scan parameter는 1 mm isotropic voxel, FOV: 256 mm, TR: 2500 ms, TE: 2.98 ms, TI: 1100 ms, PAT mode: GRAPPA, Accel. factor: PE 2였고, wave-CAIPI MPRAGE R6에서는 1 mm isotropic voxel, FOV: 256 mm, TR: 2500 ms, TE: 3.06 ms, TI: 1100 ms, PAT mode: CAIPIRINHA, Accel. factor: PE 3, 3D(slice) 2였으며, wave-CAIPI MPRAGE R4에서는 1 mm isotropic voxel, FOV: 256 mm, TR: 2500 ms, TE: 3.06 ms, TI: 1100 ms, PAT mode: CAIPIRINHA, Accel. factor: PE 2, 3D(slice)2였다. 획득한 영상은 medical image viewing solution(Terarecon, ver4.4.12, Foster City, USA)을 이용하여 axial reconstruction하였고, corona radiator, pons 그리고 cerebellar hemispheres에서 SNR과 CNR을 측정하였다. 정성적 평가 는 PACS(marotech, ver5.4.10.68, seoul, Korea)로 전송된 영상을 영상의학과 전문의 1명이 국소 병변에 대한 각 sequence 간의 진단능을 평가하였고, image quality는 영상의학과 전문의 1명과 MRI실 업무경력 10년 이상의 방사선사 1명이 blind test로 평가하였다. 정량적 평가의 통계적 검증은 Microsoft Excel 2010을 이용하여 ANOVA test를 하였다. 결 과：Conventional 3D T1 MPRAGE, wave-CAIPI R6 그리고 wave-CAIPI R4, 3개의 sequence 별로 측정한 SNR의 평균값은 Corona radiator에서 각각 160.08 ± 53.52, 185.56 ± 46.5 그리고 186.12 ± 48.44이었고, pons에서는 165.12 ± 43.41, 190.5 ± 46.24 그리고 190.94 ± 45.92이었으며, cerebellar hemispheres에서는 173.85 ± 52.67, 187.21 ± 52.13 그리고 191.92 ± 54.7이었다. Corona radiator 에서 GM(gray matter)과 WM(white matter)의 CNR 평균값은 conventional 3D T1 MPRAGE에서 52.39 ± 20.62였고 wave-CAIPI R6에서는 58.54 ± 18.32였으며 wave-CAIPI R4에서는 57.58 ± 21.11로 Conventional 3D T1 MPRAGE에 비해 wave-CAIPI R6, R4에서 SNR과 CNR이 약간 높았 다. 3 sequence 간의 focal lesion diagnosis에 대한 정성적 평가에서 100% agreement를 보였으며, image quality에 대한 평가에서 conventional 3D T1 MPRAGE에서 평균 4.85 ± 0.37, wave- CAIPI R6에서 3.82 ± 0.56, wave-CAIPI R4에서 4.10 ± 0.55 이었고 통계적 유의하였다(p≤0.05). 영상 획득 시간은 conventional 3D T1 MPRAGE는 5:48s였고 wave-CAIPI R6에서는 1:52s였으며 wave-CAIPI R4는 2:44s로, conventional 3D T1 MPRAGE에 비해 각각 67.8%, 52.8% 감소하였다. 결 론：Conventional 3D T1 MPRAGE에 비해 wave-CAIPI MPRAGE기법은 image quality의 저하 없이 scan time을 획기적으로 줄일 수 있어 임상적으로 유용할 것으로 사료된다.

This study has utilized the Quality Function Deployment (QFD) technique in order to plan the tangible (menu) and intangible (service) product of dumpling restaurant. The engineering characteristics of tangible products were classified into product planning, purchase management, production management, and information management based on the production system of foodservice. The engineering characteristics of intangible products were also classified into physical evidence, human interaction, and pre-communication based on the service operation and delivery system. As a result of analyzing the QFD, it was found that the customer hope the hygiene factor and response factor to be improved. It is analyzed that product planning, information management, and production management should be improved first in terms of engineering characteristics considering consumer needs. In the future, by utilizing the systematic product development process that the requirements of tangible and intangible product consumers are converted to the engineering characteristics, the development of competitive product within the market will be possible, and furthermore it is expected to be useful for reducing the unnecessary time and design costs due to failure of product development.

The Sakhalin pine longicorn, Monochamus saltuarius Gebler (Coleoptera: Cerambycidae), is an insect vector of the pine wilt nematode (PWN), Bursaphelenchus xylophilus (Steiner et Buhrer) Nickle, and is widely distributed in central Korea. M. saltuarius is a forest pest that seriously damages Pinus densiflora and Pinus koraiensis forests. We examined the effect of electron beam irradiation on the mating, DNA damage and ovarian development of M. saltuarius adults and sought to identify the optimal dose for sterilizing insects. Our results suggest that pine wilt disease can be effectively controlled if a large number of sterilized M. saltuarius adults are released into the field.

목 적：New fast acquisition technique인 wave-CAIPIRINHA를 적용한 MPRAGE sequence를 통해 brain의 국소병 변 진단능과 화질의 변화를 알아보고자 한다. 대상 및 방법：2017년 11월 22일부터 2018년 1월 2일까지 뇌 백질 병변이 있어 본원에서 추적 검사 중인 환자 39명(남자 21명, 여자 18명, 평균연령 54.9세)을 대상으로 conventional 3D T1 MPRAGE와 wave-CAIPI R(reduction factor) 6(3 × 2), wave-CAIPI R 4(2 × 2) 기법으로 영상을 획득하였다. 전신용 3.0T MRI(Skyra, SIEMENS, Erlangen, Germany), 64 channel head coil을 사용하였고, 모든 sequence는 sagittal로 촬영하였으며 interpolation은 적용하지 않았다. Conventional 3D T1 MPRAGE의 scan parameter는 1 mm isotropic voxel, FOV: 256 mm, TR: 2500 ms, TE: 2.98 ms, TI: 1100 ms, PAT mode: GRAPPA, Accel. factor: PE 2였고, wave-CAIPI MPRAGE R6에서는 1 mm isotropic voxel, FOV: 256 mm, TR: 2500 ms, TE: 3.06 ms, TI: 1100 ms, PAT mode: CAIPIRINHA, Accel. factor: PE 3, 3D(slice) 2였으며, wave-CAIPI MPRAGE R4에서는 1 mm isotropic voxel, FOV: 256 mm, TR: 2500 ms, TE: 3.06 ms, TI: 1100 ms, PAT mode: CAIPIRINHA, Accel. factor: PE 2, 3D(slice)2였다. 획득한 영상은 medical image viewing solution(Terarecon, ver4.4.12, Foster City, USA)을 이용하여 axial reconstruction하였고, corona radiator, pons 그리고 cerebellar hemispheres에서 SNR과 CNR을 측정하였다. 정성적 평가는 PACS (marotech, ver5.4.10.68, seoul, Korea)로 전송된 영상을 영상의학과 전문의 1명이 국소 병변에 대한 각 sequence 간의 진단능을 평가하였고, image quality는 영상의학과 전문의 1명과 MRI실 업무경력 10년 이상의 방사선사 1명이 blind test로 평가하였다. 정량적 평가의 통계적 검증은 Microsoft Excel 2010을 이용하여 ANOVA test를 하였다. 결 과：Conventional 3D T1 MPRAGE, wave-CAIPI R6 그리고 wave-CAIPI R4, 3개의 sequence 별로 측정한 SNR의 평균값은 Corona radiator에서 각각 160.08 ± 53.52, 185.56 ± 46.5 그리고 186.12 ± 48.44이었고, pons에서는 165.12 ± 43.41, 190.5 ± 46.24 그리고 190.94 ± 45.92이었으며, cerebellar hemispheres에서는 173.85 ± 52.67, 187.21 ± 52.13 그리고 191.92 ± 54.7이었다. Corona radiator에서 GM(gray matter)과 WM(white matter)의 CNR 평균 값은 conventional 3D T1 MPRAGE에서 52.39 ± 20.62였고 wave-CAIPI R6에서는 58.54 ± 18.32였으며 wave-CAIPI R4에서는 57.58 ± 21.11로 Conventional 3D T1 MPRAGE에 비해 wave-CAIPI R6, R4에서 SNR과 CNR이 약간 높았 다. 3 sequence 간의 focal lesion diagnosis에 대한 정성적 평가에서 100% agreement를 보였으며, image quality에 대한 평가에서 conventional 3D T1 MPRAGE에서 평균 4.85 ± 0.37, wave-CAIPI R6에서 3.82 ± 0.56, wave-CAIPI R4에서 4.10 ± 0.55 이었고 통계적 유의하였다(p≤0.05). 영상 획득 시간은 conventional 3D T1 MPRAGE는 5:48s였고 wave-CAIPI R6에서는 1:52s였으며 wave-CAIPI R4는 2:44s로, conventional 3D T1 MPRAGE에 비해 각각 67.8%, 52.8% 감소하였다. 결 론：Conventional 3D T1 MPRAGE에 비해 wave-CAIPI MPRAGE기법은 image quality의 저하 없이 scan time을 획기적으로 줄일 수 있어 임상적으로 유용할 것으로 사료된다.

정삼투법을 이용한 해수담수화는 역삼투 공정에 비해 에너지 절감이 가능하여 해수담수화 차세대 기술로 주목받 고 있다. 막을 기반으로 하는 수처리 분야에서 분리 성능을 향상시키고 새로운 기능을 부여하기 위해, 고분자 매트릭스에 필 러인 나노물질을 삽입하는 박막 나노복합체 분리막(thin film nanocomposite, TFN) 개발에 대한 연구가 요구되고 있다. 본 연구에서는 딥 코팅(dip coating) 방법을 기반으로 한 다층박막적층법(Layer-by-layer, LBL)을 이용하여 산화그래핀(graphene oxide, GO)의 나노 적층구조를 제어하여, 정삼투 공정에서의 높은 안정성 및 높은 수투과도 및 염 제거, 낮은 염 역확산을 갖는 그래핀 나노복합체 분리막을 개발하고자 하였다. 정삼투 공정의 성능 향상을 위한 산화그래핀의 환원 반응시간과 LBL 딥 코팅 적층 수의 최적화를 통해, 수투과도 2.51 LMH/bar, 물분자 선택성 8.3 L/g, 염 제거율 99.5%를 갖는 나노복합체 분리막 을 개발하였다. 이는 상용화된 CTA FO 분리막보다 수투과도는 10배, 물분자 선택성은 4배 높게 향상되었으며, 염 제거율은 비슷한 수준으로 나타났다.

본문에서는 법술세론의 측면에서 현행본 『한비자』에 반영된 상앙, 신불해, 신도의 사상을 중심으로 한비와의 연계성을 검토하였다. 한마디로 한비의 법술세 이론은 법가의 선구자와 선행 법가의 전개 과정을 거쳐 점차적으로 정립된 것이다. 특히 상앙, 신불해, 신도 등의 정치적 경험과 정책 방향은 한비의 법치론을 정립하기 위한 재료와 근거가 되었다. 사실 한비의 법철학의 기본 내용은 이상의 선행 법가의 실천 과정에 이미 반영된 것이 많으며, 한비는 다만 이러한 실천 경험에 대해 이론적으로 총결하고 체계적으로 논증함으로써 자신의 사상체계를 정립하였다. 한비는 전적으로 선행 법가를 계승한 것이 아니라 비판적으로 집대성하였다. 한비가 보기에 그들의 논의는 모두 미진한 것이다. 먼저 상앙에 대해서는 전반적으로 그의 법치사상을 수용하면서도 신민을 통제하는 방안을 마련하지 못하고 단지 법의 획일적 적용에 치우쳐 있다고 비판하였다. 다음으로 신불해에 대해서는 술수만을 제시하였을 뿐 실천 과정에서 야기되는 문제에 대한 대처 방법이 결여되었다고 비판하였다. 특히 한비는 신불해의 이론을 수용하면서도 오히려 그의 언행을 예로 들면서 한계성을 지적하였다. 또 다음으로 신도의 세론에 대해서는 일단 긍정하면서도 자연적 세가 아니라 인위적 세에 주목하지 못하였다고 비판하였다. 한비가 보기에 인위적 세는 바로 객관적이고 공개적인 법과 군주의 은밀한 술이다. 군주의 권위와 권세는 자연스럽게 형성되는 것이 아니라는 것이다.

The aim of the study was to investigate the effects of incentive spirometry and Ujjayi breathing technique on the pulmonary function of smokers. Subjects were individuals who had a smoking habit of at least a year. Subjects were randomly divided into 3 groups: the incentive spirometry group (n=8), Ujjayi breathing technique (n=9), and a group applying both incentive spirometry as well as Ujjayi breathing technique (n=8). Each intervention was performed twice a day, 5 times a week, for a total of 8 weeks whereupon the change in pulmonary function was evaluated. A spirometer was used to measure FVC, FEV1, and FEV1/FVC. The survey used for this study included the Fagerström Test of Nicotine Dependence (FTND) and the Shortness of Breath Questionnaire (SOBQ). Study results for the comparison within groups showed that in the group that performed both the incentive spirometry and Ujjayi breathing technique, FEV1 improved with statistical significance (p<.05). Furthermore, within this comparison the FEV1/FVC improved with statistical significance. Comparison amongst the groups showed no statistically significant differences in all areas. Following, to effectively increase pulmonary function in young adult smokers, both incentive spirometry and Ujjayi breathing technique should be employed together.

This study is based on the results of the 7th Korea Human Size Survey (Size Korea). The standard body shapes of Korean women between 25 and 34 years old were analyzed and used to develop a prototype princess line for wedding dresses. or this purpose I conducted a literature review and a survey of the actual situation of domestic ligaments. In order to select suitable ligaments for the standard body type of 25~34 year-old Korean women, I collected the most representative ligaments from around the world: Stock man from France, Superior from the USA, KIIYA from Japan, and Pig and Nonno from Korea. They were then compared and analyzed. In the form of a formal wedding dress, a prototype princess line was developed by a draping technique in order to finely implement the human body fitting. To develop the prototype of the princess line, I made test garments with muslin. 25 to 34 years old Korean female standard body type Three human subjects close to the average measurement value were selected as subjects. An exterior appearance evaluation questionnaire was created with 28 questions focusing on the main parts of the prototype princess line. The clothes were evaluated three times. In this study, aesthetic and functional elements were considered for the development of princess line prototypes for wedding dresses. In addition, the amount of spare area was given differently. This study is significant in the achievement of a dress line closest that closely matches the human body line of the standard Korean female body type.

In the defense acquisition, a company’s goal is to maximize profits, and the government’s goal is to allocate budgets efficiently. Each year, the government estimates the ratio of indirect cost sector to defense companies, and estimates the ratio to be applied when calculating cost of the defense articles next year. The defense industry environment is changing rapidly, due to the increasing trend of defense acquisition budgets, the advancement of weapon systems, the effects of the 4th industrial revolution, and so on. As a result, the cost structure of defense companies is being diversifying. The purpose of this study is to find an alternative that can enhance the rationality of the current methodology for estimating the ratio of indirect cost sector of defense companies. To do this, we conducted data analysis using the R language on the cost data of defense companies over the past six years in the Defense Integrated Cost System. First, cluster analysis was conducted on the cost characteristics of defense companies. Then, we conducted a regression analysis of the relationship between direct and indirect costs for each cluster to see how much it reflects the cost structure of defense companies in direct labor cost-based indirect cost rate estimates. Lastly a new ratio prediction model based on regularized regression analysis was developed, applied to each cluster, and analyzed to compare performance with existing prediction models. According to the results of the study, it is necessary to estimate the indirect cost ratio based on the cost character group of defense companies, and the direct labor cost based indirect cost ratio estimation partially reflects the cost structure of defense companies. In addition, the current indirect cost ratio prediction method has a larger error than the new model.

1980년대 영국은 당시 하우스와 테크노음악이 성행하였다. 대세의 음악을 틀지 않던 몇몇의 디제이들이 차별성을 두기 위해 50~60년대 발매 되었던 재즈음악에 디스코, 하우스, 힙합 리 듬을 믹스 하였고 그 과정에서 애시드 재즈라는 장르가 탄생하게 되었다. 이러한 음악적 배경 으로 애시드 재즈에서의 드럼 연주 스타일은 지속적인 안정감과 긴장감을 표현하기 위해 고스 트 노트와 엑센트를 적극 활용한다. 밴드 자미로콰이의 드러머인 데릭 멕켄지는 엑센트 기법 을 활용하여 다양한 리듬 패턴을 만들어 섹션마다 엑센트 프레이즈의 변화를 주었고 의도에 따라 엑센트 기법을 선택적으로 사용하여 연주에서의 다이나믹을 형성하였다. 본 연구는 밴드 자미로콰이의 드럼 연주기법을 분석하여 대중음악에서 크게 자리 잡는 섹션인 벌스와 코러스 에 대입할 확장 방법을 제시하고 엑센트의 음악 표현 기법은 특정 음표를 강조하여 음악의 중 심 요소인 리듬의 생명력을 부여한다는 결과를 도출한다.

최근 머신러닝은 빅데이터에 대한 분석방법으로서 학습을 통한 지능화된 문제해결 방안으로서 관심이 증가하고 있다. 본 논문은 LBSN 데이터와 머신러닝 방식을 이용하여 토지이용현황을 파악하는 분석을 시도하였다. 도시계획에 있어서 토지이용현황의 파악은 직접적인 현장 조사에 의존해 왔다. 최근 스마트폰 사용자가 증가하면서 등장하고 있는 위치기반 소셜미디어의 자료들 은 토지이용의 상황을 반영하는 빅데이터로서, 머신러닝 방법론은 이들에 대한 자동화된 분석을 할 수 있게 한다. 본 연구에서는 LBSN 자료와 머신러닝 기법을 이용하여 토지이용을 예측하는 모델을 개발하여 실제 토지이용현황 자료와의 비교분석을 수행하였다. 이러한 분석을 통해 LBSN자료를 이용한 토지이용현황의 자동화된 분석 방안에 대해 연구하였다.

This study attempted to analyze how dancheong for palace tablets during the Joseon period was designed as related to what plans and what materials were being used. It also investigated how this unique culture formed. The results found the following: First, the tablet dancheong unveiled through literature was designed using diverse techniques such as jinchae and yeokcheongchil. In jinchae, shell powder was applied to the tablet as the first lacquering, and then was colored. Second, in lacquer, maechil, chaesaekchil and jeohyeoptaechil were used. In yeokcheongchil, vegetable black, oil ash and perilla oil were applied to bitumen. Third, during the Joseon Dynasty, dancheong was applied to a tablet after first lacquering just like the danpihoe lacquering of Jiangsu Sheng, China. This tablet dancheong technique was developed based on a unique Korean lacquering culture that had been handed down from ancient times.

휴먼 비트박스의 경우 거리에서 생겨난 문화로 특정한 기예(技藝)나 특정 장르에서 보컬을 받쳐주는 정도로 여겨져, 특정 방법론이 존재한다고 예측하기 보다는 개인의 즉흥적 능력치에 의존한다 생각하기 쉽다. 물론 개인의 능력에 상당히 의존하는 부분도 있지만, 효과적인 사운 드의 구성을 위한 일정한 방법론 또한 그에 준하여 존재한다. 본 연구는 바로 이러한 휴먼 비 트박스의 방법론을 제시하는 것에 그 목적을 두고 연구한다. 휴먼 비트박스와 루핑 머신을 이 용하는 스트릿 아티스트 Dub Fx는 휴먼 비트박스를 주로 사용해 힙합과 레게 기반의 음악을 연주하는 뮤지션으로 그의 음악 특성은 다음과 같이 분석된다. 첫째, 휴먼 비트박스 패턴만이 아닌 다른 악기들도 사용하기에 간단한 진행의 비트 패턴을 사용한다. 둘째, 악기의 구성은 적게는 두 가지, 많게는 네 가지 정도의 간단한 구성으로 빠르게 음악을 만들어 간다. 셋째, 악기를 사용하는 일정한 순서가 존재하며 그 순서는 비트, 베이스, 보컬 이펙트, 그리고 그 외의 인스트루멘탈(Instrumental)의 순이다. 또한 과도한 리버브의 효과를 주어서 사운드를 채우기도 한다. Dub Fx의 작업을 토대로 본 휴먼 비트박스를 사용한 음악 제작 과정에는 일정 한 규칙이 존재한다는 결과가 도출되며 효과적인 사운드의 구성을 위해 적용된 위의 규칙들은 힙합뿐만이 아닌, 일렉트로닉 뮤직, 재즈 등 즉흥성을 바탕으로 한 여러 타 장르에도 어울릴 수 있는 가능성을 제시한다.