The main object of this study is to investigate the collection characteristics of wet-type rotating porous disk system experimentally. The experiment is carried out to analyze the pressure drop and collection efficiency for the present system with the experimental parameters such as system inlet velocity, stage number, tube diameter, inlet concentration, etc. In results, for the present system, at 5 stage and υin=1.8 m/s, the pressure drop becomes significantly lower as 64 mmH2O in comparison with that of the conventional wet type scrubber (Venturi scrubber, over 250 mmH2O). The collection efficiencies increase with higher inlet velocity showing 92, 95.7, 98.4%, while SO2 removal efficiencies decrease with increment of inlet velocity as 80, 65, 50% at υin=1.08, 1.44, 1.8 m/s and tube diameter Dt=10 mm, respectively. The present system is to be considered as an effective compact system for a simultaneous removal of particle/gas phase pollutants from marine diesel engines.

Swelling of the heat-treated netting for gillnet was estimated through the netting height in square acrylic tank. Experimental Nylon netting and PBSAT netting were heat-treated by using the high-degree vacuum method in hot water after net making. Heat-treatment temperatures were conducted with Nylon netting 105°C and PBSAT netting 62°C, 65°C, 66°C, 67°C. The swelling measurement method of a netting using the square tank was capable of the reduction measurement errors comparing with measurement methods of a mesh inner angle and the shortening rate of a mesh size. In addition, this method was available to comparison evaluation for each netting more easily. Wet type heat-treatment apparatus with high-degree vacuum was shown higher 7∼8°C inner side temperature than a setting temperature. The tensile strength and elongation of Nylon netting and PBSAT netting were shown higher wet condition than dry condition. The tensile strengths of PBSAT monofilaments in dry and wet condition were sharply decreased at heat-treatment temp. 75°C than heat-treatment temp. 74°C

The main object of this study was to investigate the collection characteristics of wet-type cyclone with wall cavity. The experiment was executed to analyze the characteristics of pressure drop and collection efficiency for the present system with the experimental parameters such as water spray, water spray type, inlet velocity etc. In results, for the present system of wet-type, the pressure drop represented 35 mmH2O, while in dry-type 33 mmH2O showing lower 6% at vin=21 m/s. In case of vin=21 m/s and water spray 200 mL/min, the collection efficiency of the present system became significantly higher as 96.8% comparing to that of the conventional wet-type scrubber. Additionally, for 200 mL/min, SO2 removal efficiencies decreased with the increment of inlet velocity representing 75.0, 62.5, 50.0%, at vin=6, 9, 12 m/s, respectively.

In recent years, researchers have put a considerable effort to decrease the emission of harmful gaseous pollutants to the atmosphere. In order to remove simultaneously SO₂ and NOx from the flue gas of small and medium-sized ship, we designed minimal wet scrubber inside a compact multistage modular system. In this study we proceed experiment of elemental technology at each stage of the scrubber. The each stage is oxidation of NO which is the main component of NOx, and removal of SO₂, respectively. NaClO₂ was used to oxidize NO gas, and NaOH was used to remove SO₂gas. The maximum NO conversion efficiency and the SO₂ removal ficiency are both indicate 100%.

The performance of inorganic sludge separation system is evaluated. Anaerobic digester effluent sludge is used for feed sludge of this system and hydrocyclone is used for inorganic sludge separation. For phosphorus removal and recovery MgCl2 is pumped into MAP growth tank, a component of inorganic sludge separation system. Using this system inorganic sludge which contained less than 40 % of organic matter can be discharged stably and the maximum amount of separated inorganic sludge is 13.4 % of influent sludge based on dry solid. The amount of phosphorus recovered as MAP(as P) is 16.7 % to influent T-P.

The relationship the between electrical properties and surface roughness (Ra) of a wet-etched silicon wafer were studied. Ra was measured by an alpha-step process and atomic force microscopy (AFM) while varying the measuring range 10×10, 40×40, and 1000×1000μm. The resistivity was measured by assessing the surface resistance using a four-point probe method. The relationship between the resistivity and Ra was explained in terms of the surface roughness. The minimum error value between the experimental and theoretical resistivities was 4.23% when the Ra was in a range of 10×10μm according to AFM measurement. The maximum error value was 14.09% when the Ra was in a range of 40×40μm according to AFM measurement. Thus, the resistivity could be estimated when the Ra was in a narrow range.

The electrical properties and surface morphology changes of a silicon wafer as a function of the HF concentration as the wafer is etched were studied. The HF concentrations were 28, 30, 32, 34, and 36 wt%. The surface morphology changes of the silicon wafer were measured by an SEM (80˚ tilted at ×200) and the resistivity was measured by assessing the surface resistance using a four-point probe method. The etching rate increased as the HF concentration increased. The maximum etching rate 27.31 μm/min was achieved at an HF concentration of 36 wt%. A concave wave formed on the wafer after the wet etching process. The size of the wave was largest and the resistivity reached 7.54 ohm·cm at an 30 wt% of HF concentration. At an HF concentration of 30 wt%, therefore, a silicon wafer should have good joining strength with a metal backing as well as good electrical properties.

Coatings composited with alumina and Perfluoro alkoxyalkane (PFA) resin were deposited on stainless steel plate (SUS304) to further improve corrosion resistance. Plate (ca. 10μm) and/or nanosize (27~43 nm) alumina used as inorganic additives were mixed in PFA resin to make alumina-fluoro composite coatings. These coatings were deposited on SUS304 plate with wet spray coating and then the film was cured thermally. According to the amount and ratio of the two kinds of alumina having plate morphology and nano size, corrosion resistance of the film was evaluated under strong acids (HF, HCl) and a strong base (NaOH). The film prepared with the addition of 5~10 wt% alumina powders in PFA resin showed corrosion resistance superior to that of pure PFA resin film. However, for the film prepared with alumina content above 10 wt%, the corrosion resistance did not improve with the physical properties, such as surface hardness and adhesion. The film prepared with plate/nanosize (weight ratio = 1/2) alumina especially enhanced the surface hardness and corrosion resistance. This can be explained as showing that the plate and the nanosize alumina dispersed in PFA resin effectively suppressed the penetration of cations and anions due to the long penetration length and fewer defects that accompany the improved surface hardness under a serious environment of 10% HF solution for over 120 hrs.

Korea. Two kinds of jochung products were prepared from steamed rice(SR) and wet-milled rice flour(WRF) by rice cultivated from 2006 to 2010. It is common to add a liquefying enzyme for rice liquefaction(4 ㎖/1, 000 g rice, at 90～95℃, 3 h) and saccharogenic enzyme with malt(45 g/1, 000 g rice, at 55～57℃, 6 h). In order to evaluate the quality characteristics of jochung, producing rate, pH, solidity, reducing sugar, dextrose equivalence(D.E.), viscosity, total phenolic compound, color value and sensory evaluation were carried out. In terms of the producing rate of jochung, WRF jochung was produced about 7.4% much more than SR jochung. There was no difference in producing rate between the jochung cultivated from 2006 to 2010 rice. The pH varied from 4.86～5.66, solidity was 79.48～82.28%. Color L value was 25.82～27.92, a value of 1.28～2.81, b value were 2.98～4.33. The results of sensory evaluation for jochung, as a whole, received higher score than for the commercial product(Daesang Co., Ltd, Seoul, Korea), overall acceptability score was the highest in the 2008SR. Reducing sugar, dextrose equivalence(D.E.) and total phenolic compounds were determined to be higher WRF jochung than SR jochung, while viscosity was lower WRF jochung than SR jochung. These results are thought to be due to increased surface area of rice by milling. SR jochung manufacturd by wet-milled rice flour will increase the producing rate for jochung, thereby saving manufacturing time and costs.

하이퍼볼릭 쉘로 구성된 냉각탑에서 쉘의 형상은 풍하중에 대하여 냉각탑 전체의 동적 거동에 민감하게 응답한다. 이에 따라 냉각탑 설계 시 기하형상의 결정은 매우 중요하며 일반적으로 고유진동수를 기반으로 하여 산정한다. 본 연구의 목적은 냉각탑 쉘의 구조적 거동에서 형상변수가 미치는 영향을 파악하고자 한다. 기존의 냉각탑 형상변수를 변화시켜 32개의 모델을 선정하였고 이를 1차 고유진동수를 기반으로 하여 분석한 후, 3개의 대표적인 형상을 선택하여 선형 해석을 수행하였다. 그 결과, 전체적으로 작은 반지름을 가지는 기하형상이 높은 1차 고유진동수를 나타내고 풍하중에 대하여 덜 민감한 시스템이 되는 것을 알 수 있었다.

지난 2011년 3월의 후쿠시마 원전 사고시 원자로 건물에서의 연쇄적인 수소폭발이 발생하였을 때 관계 자들은 제1원전 4호기의 폭발에 더욱 놀랐었는데 이는 그 당시 4호기는 정기보수를 위하여 원자로내 모 든 핵연료를 저장조에 보관중이었기 때문이다. 저장조내 냉각수 유실로 노심에서 옮겨진 핵연료가 공기 중에 노출되어 수소가 발생하고 임계가 도달하였다면 더욱 심각할 수도 있기 때문이었는데 다행히 추후 에 양호한 냉각수 상태가 확인되어 우려할 상황을 피할 수 있었다. 본 논문에서는 후쿠시마 원전 사고를 계기로 국내 원자력 발전소내 핵연료 임시 저장시설의 안전성과 관련하여 중대사고 관점에서 검토해 보 고자 한다.

Nickel recovery method was studied by the wet process from the catalyst used in hydrogenation process. Nickel content in waste catalyst was about 16%. At the waste catalyst leaching system by the alkaline solution, selective leaching of nickel was possible by amine complex formation reaction from ammonia water and ammonium chloride mixed leachate. The best leaching condition of nickel from mixed leachate was acquired at the condition of pH 8. LIX65N as chelating solvent extractant was used to recover nickel from alkaline leachate. The purity of recovered nickel was higher than 99.5%, and the whole quantity of nickel was recovered from amine complex.

Embedding of active devices in a printed circuit board has increasingly been adopted as a future electronic technology due to its promotion of high density, high speed and high performance. One responsible technology is to embedded active device into a dielectric substrate with a build-up process, for example a chipin-substrate (CiS) structure. In this study, desmear treatment was performed before Cu metallization on an FR-4 surface in order to improve interfacial adhesion between electroless-plated Cu and FR-4 substrate in Cu via structures in CiS systems. Surface analyses using atomic force microscopy and x-ray photoemission spectroscopy were systematically performed to understand the fundamental adhesion mechanism; results were correlated with peel strength measured by a 90o peel test. Interfacial bonding mechanism between electrolessplated Cu and FR-4 substrate seems to be dominated by a chemical bonding effect resulting from the selective activation of chemical bonding between carbon and oxygen through a rearrangement of C-C bonding rather than from a mechanical interlocking effect. In fact, desmear wet treatment could result in extensive degradation of FR-4 cohesive strength when compared to dry surface-treated Cu/FR-4 structures.

습식분쇄의 최적조건을 얻고자 부형제 종류, 농도, 습식분쇄시 rotor speed, bead size, feed rate, 분쇄회수를 달리하여 분쇄한 결과, 부형제로는 gum arabic을 사용하여 5%의 농도로 첨가할 때 가장 좋은 분쇄효과를 나타내었다. Rotor speed를 달리하여 습식분쇄한 결과, rotor speed가 증가할수록 좋은 결과를 나타내어 4,000 rpm에서 가장 우수한 것으로 나타났다. 원료와 직접 부딪혀 분쇄를 하게 되는 bead는 0.4 mm의 크기를 사용하였을 때 가장 작은 사이즈로 분쇄되는 것으로 나타났다. 분쇄가 이루어지는 chamber내에 원료를 공급하는 비율에 따른 결과에서는 40 L/h 의 속도로 공급했을 때 가장 작은 입도분포를 보였다. 분쇄회수에 따른 영향은 횟수에 따라서는 8회 이상으로 분쇄하였을때 0.6 μm이하의 입도분포가 90% 이상으로 나타나 10회를 분쇄하였을때 가장 좋은 효과를 나타내었다. 연속운전과 비연속운전의 비교에서는 연속운전이 더 효율적이었으며 부형제 종류에 따른 영향은 gum arabic을 첨가하여 분쇄하였을때 가장 우수한 결과를 나타내었다. 따라서 적절한 농도와 종류의 부형제 사용과 rotor speed, bead size, feed rate, 용매와의 혼합비의 최적공정을 수립한 습식분쇄기술로 초미세액상칼슘의 제조가 가능하였고, 습식분쇄기술을 식품가공기술로 활용할 수 있는 가능성을 확보하였다.

In this study we investigated the effect of the multi-step texturing process on the electrical and optical properties of hydrogenated Al-doped zinc oxide (HAZO) thin films deposited by rf magnetron sputtering. AZO films on glass were prepared by changing the H2/(Ar+H2) ratio at a low temperature of 150˚C. The prepared HAZO films showed lower resistivity and higher carrier concentration and mobility than those of non-hydrogenated AZO films. After deposition, the surface of the HAZO films was multi-step textured in diluted HCl (0.5%) for the investigation of the change in the optical properties and the surface morphology due to etching. As a result, the HAZO film fabricated under the type III condition showed excellent optical properties with a haze value of 52.3%.

High-pressure abrasive entrained jet have rapidly become important machining technology over the last two decades. However, suspension jet by high-pressure has been recently developed for packaging sawing. Ideally, diamond materials should be used for components in abrasive water-jet systems that are subject to high erosive conditions. Using the diamond orifices improve maintenance and extend wear part life. This paper gives insights to using an abrasive suspension jet with diamond orifice. The influences of orifice material and orifice design are evaluated.