검색결과

검색조건
좁혀보기
검색필터
결과 내 재검색

간행물

    분야

      발행연도

      -

        검색결과 47

        1.
        2025.02 KCI 등재 구독 인증기관 무료, 개인회원 유료
        일반적으로 전기 패널은 용접이나 앵커링을 통해 기초에 설치된다. 콘크리트 기초-앵커 시스템에서 고려해야 할 열화 요인에 는 콘크리트 기초의 균열이 포함된다. 콘크리트 균열은 전기 패널의 앵커에 영향을 미치는 열화 현상 중 하나로 간주될 수 있다. 또한 독립반 및 열반된 전기 패널의 동적 특성은 상당히 다를 수 있다. 그러나 많은 연구자들이 하나의 전기 캐비닛 시편으로 진동대실험을 수행하였다. 따라서 열반 구성을 고려하여 동적 특성을 평가할 필요가 있다. 본 연구에서는 0.5 mm 및 1.0 mm 균열 폭을 고려하여 콘크리트 기초-앵커 시스템을 설계하였다. 콘크리트 기초-앵커 시스템을 진동대에 고정하고 1∼3개의 열반으로 구성된 단순화된 캐비 닛 모델을 설치하였다. 열반 수와 콘크리트 균열을 매개변수로 고려하여 진동대에 의한 공진주파수 검색 실험을 수행했으며 각 실험편 의 공진 주파수를 비교하였다.
        4,000원
        2.
        2024.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        This study analyzed the epilithic diatom community and ecological health of freshwater streams using environmental DNA (eDNA)-based metabarcoding technology. eDNA metabarcoding is a method that analyzes biological communities by performing PCR amplification followed by next-generation sequencing (NGS), offering higher sensitivity and faster results compared to traditional microscopic analyses. The study compared the eDNA metabarcoding results of ribulose bisphosphate carboxylase large chain gene (rbcL) targeting epilithic diatoms according to Taq polymerases (SuperFi II, GainBlue, EzPCR, and AccuPower). SuperFi II and GainBlue yielded the highest number of reads and zOTUs, with GainBlue showing particularly uniform read distribution, allowing for more accurate analysis for community diversity of epilithic diatoms. On the other hand, EzPCR and AccuPower exhibited lower number of reads and zOTUs, making them less suitable for the community diversity. In terms of community similarity analysis, SuperFi II and GainBlue produced highly similar results, while EzPCR and AccuPower showed significant differences. This study demonstrates that PCR Taq polymerases significantly influence community diversity and similarity analyses of epilithic diatoms, with GainBlue providing the most stable and accurate results. Our findings serve as a valuable foundation for improving the accuracy of eDNA-based metabarcoding analyses of diatoms.
        4,000원
        3.
        2024.10 구독 인증기관·개인회원 무료
        콘크리트 포장의 평탄성과 내구성은 환경 조건에 크게 영향을 받으며, 슬래브 상하부 간의 온습도 차이는 부등건조수축 및 와핑 (Warping) 현상을 유발하여 포장의 장기 성능 저하를 초래할 수 있다. 이는 주행성 저하, 균열 발생, 유지보수 비용 증가의 원인이 되 며, 특히 터널과 같은 특수 환경에서는 상하부 간의 습도 차이가 더욱 크게 나타나 부등건조수축이 심화될 가능성이 높다. 터널 내부 는 직사광선의 영향을 받지 않지만, 통풍이 잘 이루어져 건조한 환경이 조성되며, 이러한 조건에서는 슬래브 상부에서 수분 손실이 가 속화되고 하부는 습윤 상태를 유지하여 상하부 간의 큰 습도 차이를 발생시킨다. 이는 슬래브의 비균일한 수분 이동을 유발하여 부등 건조수축을 더욱 크게 발생하게 한다. 국내에서는 터널 길이가 500m 이상인 장대 터널에서 콘크리트 포장 적용이 증가하고 있으며, 아스팔트 포장 대비 화재 시 유독가스 발생 위험이 낮다는 이유로 국토교통부에서 콘크리트 포장을 권장하고 있다. 이로 인해 터널 내 콘크리트 포장의 사용이 증가하고 있 으나, 기상환경 변화 및 습도 관리 미흡으로 인해 콘크리트 포장 줄눈부에서의 평탄성 불량 문제가 빈번하게 발생하고 있다. 이러한 문제는 주행성 저하, 도로 이용자의 민원 증가 및 유지보수 비용 상승을 초래하고 있어, 구체적인 원인 분석과 대책 마련이 필요한 실 정이다. 따라서 본 연구는 터널과 같은 특수 환경에서 습도 조건이 콘크리트 슬래브의 부등건조수축에 미치는 영향을 실험적으로 분석하고, 슬래브의 수평 변형률 및 수직 변위를 측정하여 건조 수축에 따른 변형 거동을 정량적으로 평가하고자 하였다. 다양한 습도 조건에서 슬래브의 변형 양상을 비교 분석함으로써, 터널 환경에 적합한 콘크리트 포장 설계 및 유지관리 기준을 제시하고, 콘크리트 포장의 장 기 성능을 개선하기 위한 대책을 마련하고자 한다.
        4.
        2024.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        마비성 패류 독소(Paralytic shellfish poisoning, PSP)는 유해 조류에 의해 생성되며, 독소에 노 출된 수산물을 섭취하였을 때 중독이 발생한다. 수산물 중 PSP를 검출하는 표준 시험법인 Mouse bioassay (MBA)는 낮은 검출한계와 동물 윤리 문제로 대체 시험법의 개발 필요성이 대 두되고 있다. 이러한 대체 시험법 중, PSP가 신경 세포막의 Na+ 채널을 차단하는 기전을 이 용한 마우스 뇌신경 모세포종 세포 기반 시험법(Neuro-2a assay)의 표준화를 위한 노력이 대두 되고 있다. Neuro-2a assay의 원리는 Neuro-2a 세포주에 Na+/K+ ATPase 억제제인 Ouabain (O)과 Na+ 채널 활성화제인 Veratridine (V)을 처리하여 과도한 Na+ 유입으로 인한 세포사멸을 유도한 상태에서, Na+ 채널 억제제인 PSP를 처리하게 되면 Na+ 유입이 차단되어 세포가 생존 하는 것을 측정하는 것이다. 본 연구에서는 PSP 검출을 위한 Neuro-2a assay를 국내 연구 환 경에 맞게 다양한 매개변수를 개선하여 최적 시험법을 확립하고자 하였다. 고려한 매개변수 들은 세포밀도, 배양 조건 및 PSP 처리 조건 등으로, 그 결과는 아래와 같다. 초기 세포밀도 는 40,000 cells/well로, 세포 배양시간 및 처리시간은 각각 24시간으로 설정하였다. 또한 최적 O/V 농도는 500/50 μM로 설정하였다. 본 연구에서 PSP 중 Saxitoxin (STX)에 대해서 O/V 처 리가 된 상태에서 S자형 용량-반응 그래프가 도출되는 8가지 농도(368~47,056 fg/μl)를 확인 하였고, Neuro-2a assay의 실험실 간 변동성 비교를 통해, 실험의 적정성 확인을 위한 5가지 Quality Control Criteria와 실험 데이터의 신뢰가능 범위(Data Criteria) 6가지를 설정하였다. 확 립된 조건으로 Neuro-2a assay를 진행한 결과 반수영향농도(EC50) 값은 약 1,800~3,500 fg/μl 로 나타났다. 실험실 간 변동성 비교 결과, Quality Control Criteria 값 및 Data criteria 값의 변 동계수(coefficients of variation (CVs))가 1.98~29.15% 범위로 산출되어 실험의 적정성 및 재현 성이 확인되었다. 본 연구를 통해 우리나라에서 활용할 수 있는 PSP 검출용 Neuro-2a assay 시험법의 최적 조건 및 5가지 Quality control 기준을 제시하였고, PSP 중 대표적인 독소인 STX 을 대상으로 Neuro-2a assay를 실시한 결과 유의한 EC50 값을 산출할 수 있었으며, 향후 국 내 수산물을 대상으로 MBA를 대체할 수 있는 PSP 검출법으로 활용될 것으로 기대된다.
        4,500원
        5.
        2024.04 구독 인증기관·개인회원 무료
        노후 구조물의 동적 특성 평가를 위해 대표적인 접촉식 센서인 LVDT와 가속도계를 활용한다. 전통 적인 센서의 데이터 신뢰성은 높지만, 작동 원리로 인하여 대상 구조물의 물리적 접근과 센서의 설치 가 필요하다. 조밀한 센서 설치를 위해선 많은 수의 센서와 데이터 수집장치도 추가적으로 필요하다. 이런 단점을 보완하고자 비접촉식 센서의 개발이 활발히 진행 중이며, 특히 비전센서를 활용한 동적 변위 측정에 관한 연구 및 개발에 많은 진척이 있다. 비전센서를 활용한 동적 변위 측정 시스템은 내 적 파라미터 및 외적 환경조건에 따라 측정 정확도가 크게 변화한다. 주된 내적 파라미터로 영상장비 의 공간분해능은 이미지 센서의 물리적 크리와 촬영거리의 증가 혹은 관심영역이 작아짐에 따라 영향 을 많이 받는다. 외적 환경조건으로 저조도 환경에서 타겟의 밝기차이가 줄어들어 이미지 프로세싱 과 정에서 불리한 조건이며, 이는 동적 변위 측정 정확도 저하로 이어진다. 본 연구에서 저조도 환경에서 비전센서의 운용거리 한계를 초해상화를 적용하여 극복하고자 하며, 인공적 및 자연적 타겟에 대한 동 적 변위 측정 성능을 비교 분석하였다. 동적 변위 측정 실내 실험을 위해 저조도 조건에서 3층 전단 구조물을 9Hz로 가진하였다. 동시에 Sony사의 DSC-100M7 카메라를 활용하여 조화진동으로 인해 발생되는 각층의 변위를 FHD화질 120FPS로 촬영하였고 측정 정확도 비교 분석을 각층의 LVDT 측 정값으로 진행하였다. 촬영거리를 10m를 기준으로 10m씩 증가하면서 최대 40m까지 변위 값을 측정 하였으며, 공간분해능 증가를 위해 GAN기반 초해상화 모델인 RealSR을 적용시켰다. 초해상화를 활용 하여 동적변위를 측정한 결과 저조도 환경에서도 비전센서의 운용 거리가 증가함을 확인할 수 있었으 며, 동시에 변위 측정 정확도도 함께 상승하는 것을 보여줬다.
        6.
        2024.03 구독 인증기관·개인회원 무료
        대한민국의 도로의 증가로 인한 복잡화에 따라 터널의 수와 연장이 지속적으로 증가하고 있다. 본 연구는 시멘트콘크리트 포장의 성 능과 수명에 미치는 환경조건의 영향을 분석한다. 현재까지 시공된 고속도로의 많은 부분이 시멘트콘크리트 포장으로 되어 있으며, 이 에 대한 연구는 오랫동안 진행되어 왔다. 부등건조수축은 슬래브의 상하부 온습도 차이에 의해 발생하며, 일일 및 계절적 주기에 따라 발생한다. 일반적으로, 온습도 변화에 따라 컬링이나 와핑이 발생하는데, 컬링은 낮에는 높은 온도로 인한 하향 수축, 밤에는 낮은 온 도로 인한 상향 수축을 나타낸다. 그러나, 환경조건 변화에 따른 콘크리트 내부 습도 변화에 대한 이해는 아직 크게 연구가 진행되지 않아 포장 설계에 적절히 반영되지 못하고 있다. 이러한 연구는 터널 등 배수가 어려운 지역에서 콘크리트포장의 적절성을 판단하여 공용수명에 기여할 것으로 예상한다. 본 연구에서는 슬래브의 하부 조건이 콘크리트 내부 습도에 미치는 영향을 실험적으로 조사한다. 콘크리트 시편을 제작하여 특수한 환경조건에서의 습윤 차이를 모사하여 수분 이동 특성을 연구한다. 실험에서는 슬래브의 한쪽면을 고정하고 반대편이 부등건조수축으 로 인해 발생하는 변형률과 수직변위를 측정할 장비를 설치하여 시간에 따른 변화량을 확인한다.
        7.
        2023.09 KCI 등재 구독 인증기관 무료, 개인회원 유료
        As the capacity of renewable power generation facilities rapidly increases, the variability of electric power system and gas turbine power generation is also increasing. Therefore, problems may occur that require urgent repair while the gas turbine rotor is stopped. When the gas turbine rotor turning is stopped and then restarted, if the turning period is not appropriate, severe vibration may occur due to rotor bending. As a result of the experiment, it was confirmed that normal operation is possible when the gap data measured at the start of rotor turning after maintenance work is similar to the existing value. And the vibration value at the start of rotor turning was lower as the rotor temperature was lower or the stop period was shorter.
        4,000원
        8.
        2023.04 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Demand for research on the use of hydrogen, an eco-friendly fuel, is rapidly increasing in accordance with global environmental problems and IMO environmental regulations in the shipbuilding and marine industry. In the case of hydrogen, similar to liquefied natural gas, it has a characteristic that its volume decreases hundreds of times during phase transformation from gas to liquid, so it must be stored in a tank in the form of liquefied hydrogen for transport efficiency. The material of the liquid hydrogen tank is selected in consideration of mechanical properties and hydrogen embrittlement at cryogenic temperatures. In this study, welding research was conducted on STS316L material, which was most commonly used in the space industry. In this study, flux cored arc welding was performed under 4 welding conditions to derive the optimal welding conditions for STS316L material, and then mechanical properties of the welded part were compared and analyzed.
        4,000원
        9.
        2022.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        대표적인 비구조요소인 배관의 지진에 의한 손상은 관성력과 두 지지점 사이의 위상차에 의해 작용하는 반복하중 그 리고 허용변형량을 초과하는 상대변위 등에 의해 발생할 수 있다. 특히 주요 손상모드는 큰 반복하중에 의한 저주기피로임이 많은 실험적 연구를 통하여 알려졌다. 따라서 과도한 지진변위에 의한 배관의 손상을 방지하기 위하여 지진상대변위가 발생할 수 있는 위치에 지진분리이음 또는 지진분리장치의 적용이 요구된다. 신축관이음 중 하나인 벨로우즈는 지진분리이음으로 적용 할 수 있다. 본 논문에서는 3ply 금속 벨로우즈 신축관이음의 온도차에 의한 내진성능의 변화를 분석하기 위한 실험적 연구를 수행하였다. 상온환경에서 점진증폭 반복하중재하실험을 수행하였으며, -20°C의 저온조건에서 동일한 실험을 수행하고 그 결과 를 비교하였다. 실험 결과로부터, -20°C의 저온환경에서 금속벨로우즈의 변위성능은 약 10% 저하될 수 있음을 확인하였다.
        4,000원
        10.
        2022.08 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In order to experimentally investigate the operation characteristics of the multi-heat pump with 3 indoor units, the dynamic characteristics of the cooling cycle is studied using the psychrometric multi-calorimeter. The compressor of the heat pump is the scroll inverter type, and since 3 indoor units operate cooling at the same time, it is operated at 100% full load. In particular, 3 types of indoor unit temperatures (20, 24, 26°C) are selected to understand the operation process of the multi-heat pump by the setting temperature. From this experiment, the compressor controls the EEV opening for each indoor unit while varying the frequency according to the initial start, transient, and steady operation. In addition, as the setting temperature increases in the steady range, the frequency of the compressor and the average opening degree of the EEV decrease.
        4,000원
        11.
        2022.08 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In the present study, it is conducted to understand the heating performance and compressor operation characteristics according to 7 indoor unit combinations and 3 setting temperatures of the inverter multi-heat pump under heating standard temperature conditions. Heating capacity, COP and compressor frequency are investigated using the multi-calorimeter. The indoor unit combinations are simultaneous operation(A+B+C), partial operation(A+C, A+B, B+C) and independent operation(A, B, C), and the setting temperature is 20, 21, and 30°C. Since the increase in the setting temperature increases the compress frequency, the heating capacity increases, but COP decreases due to the increase in power consumption. The frequency increases as the indoor unit combination capacity increases, and decreases as the setting temperature decreases in the steady state.
        4,000원
        13.
        2022.02 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Conversion to modern hydrogen energy is required, and research on liquefied hydrogen cargo containment systems is needed for large-capacity transport and storage. In this study, changes in the mechanical properties of the adhesive required for storage and transport in liquid hydrogen were confirmed. The lap shear test was performed by realizing cryogenic conditions in a small chamber using liquid nitrogen and liquid helium. There was an increase of 11.0% in the -180℃ condition compared to room temperature, and an increase of 1.8% in the -230℃ condition compared to the -180℃ condition was confirmed. In the case of shear strain, it is known that it decreases as the temperature goes down. As a result of the experiment, it was confirmed that the value at room temperature and the value at -180℃ reduced the shear strain by 5.0%, and -230˚ compared to the -180℃ condition. An increase of 1.5% was confirmed in the C condition. In the case of the specimen tested at -230℃, the deformation in the gripper part was larger than in other tests, and it is judged that the maximum shear strength and shear strain were affected. In addition, in this study, there is a limitation in the experiment at -230°C rather than 253°C, which is the boiling point of hydrogen
        4,000원
        14.
        2020.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The purpose of this study was to establish the optimum experimental conditions by investigating the relationship between the nine experimental conditions using Taguchi technique. Through experiments, we found that the weight, thickness, and length of the sample were most affected by the angle at which the sample was installed, while the width had the largest influence on the sample's x-axis and the inner diameter. It was confirmed. Therefore, through this experiment, it was confirmed that the installation angle of the product had the greatest influence on the error occurrence of the product during 3D printer processing.
        4,000원
        15.
        2019.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this study, the performances of the refrigeration unit for the box under actual operating conditions were examined by using the constant temperature and humidity chamber (air enthalpy method). For this purpose, the degree of superheat, pressure, and temperature were measured while changing the EEV opening, the compressor speed, the outdoor temperature, and the load in the refrigeration cycle of the refrigeration unit. The highest cooling performance was found at EEV 33%. However, EEV 35% with low compression ratio and degree of superheat was the most reliable in terms of reliability. Considering the compressor speed and cooling performance, the refrigeration unit was in an optimal condition at the compressor speed 3,040RPM. The results of this study will be provided as basic data for the optimal design of refrigeration units for box.
        4,000원
        16.
        2018.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Graphene oxide (GO) laminate is a new promising material for water purification system, which has extraordinary permeability only for water molecule. It consists of numerous nano-channels, in which water molecules could be nano-confined, resulting in slip of the molecules for very fast transportation speed. In this study, water penetration rate via different thickness of GO membrane according to driven pressures are measured experimentally, so that speed of water molecules and permeability are evaluated. Generally, water penetration rate via a membrane with macroscopic-sized channel increases linearly with pressure difference between up and bottom side of the membrane, but that via GO membrane approaches asymptotic value (i.e. saturation) as like a log function. Moreover, the permeability of GO membrane was observed in inverse proportion to its thickness. Based on the experimental observations, a correlation for volume flux via GO membrane was suggested with respect to its thickness and external pressure difference.
        4,000원
        17.
        2018.04 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this paper, the combustion characteristics of constant volume combustion chamber(CVCC) were experimentally investigated when biodiesel is mixed with pure gasoline. The experiment was performed on two gasoline biodiesel samples designated by GB05 and GB20 which is mixed with 5% and 20% biodiesel respectively. It was confirmed that the ignition delay time decreases as the temperature of injection engine increases due to ignition delay. Also, it was shown that the ignition delay time decreases as the biodisel mixing ratio increases from 5% to 20%.
        4,000원
        18.
        2018.03 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        This study investigated the effect of the grinding media of a ball mill under various conditions on the raw material of copper powder during the milling process with a simulation of the discrete element method. Using the simulation of the three-dimensional motion of the grinding media in the stirred ball mill, we researched the grinding mechanism to calculate the force, kinetic energy, and medium velocity of the grinding media. The grinding behavior of the copper powder was investigated by scanning electron microscopy. We found that the particle size increased with an increasing rotation speed and milling time, and the particle morphology of the copper powder became more of a plate type. Nevertheless, the particle morphology slightly depended on the different grinding media of the ball mill. Moreover, the simulation results showed that rotation speed and ball size increased with the force and energy.
        4,200원
        19.
        2017.10 구독 인증기관·개인회원 무료
        시뮬레이터를 활용한 실험과 검증은 자율자동차의 상용화 기술 확보에 필요 충분한 검증 수단일까? 이 질문에 대한 아주 명백한 답변으로 거의 모든 시스템 엔지니어링의 기본으로 여기는 V-Cycle(System Life cycle process model)(ISO 26262) 을 적용한 실험과 검증을 들 수 있겠다. 위와 같은 개발절차를 따름에 있어 시뮬레이터는 필수 조건이고 경제성과 높은 신뢰도를 구축 하는데 분명하고 명백한 기준으로 사용될 수 있음을 보여 준다고 할 수 있다. 그러므로 시뮬레이터를 적용한 실험, 검증에 대한 유효성을 소모적으로 논하기 보다 효율적이고 고 신뢰성을 확보하기 위한 시뮬레이터의 구축(필요 조건)과 다양한 실험방법을 도출하고 더 나아가 시뮬레이터를 개발 툴로 전환, 활용 가능하도록 꾸준한 연구와 투자가 요구 된다고 볼 수 있다. 특히, 자율 자동차의 상용화 기술 개발 과정에서 시뮬레이터는 매우 유연하고 생산적인 개발 도구로 활용될 수 있으며 이를 위해 시뮬레이터의 요구 조건은 과거 어느때보다 보다 높은 수준의 추종성과 현실감이 요구 되어 질 수 밖에 없다 본 발표에서는 시뮬레이터 활용 예시(제안)를 통해 자율자동차 상용화 기술개발에 필요한 시뮬레이터의 필요 조건에 대해 살펴보고자 한다.
        20.
        2017.08 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this study, thermal performance test of VMD module was performed, prior to the construction of the demonstration plant using the vacuum membrane distillation (VMD) module of the capacity of 400 m3/day and to the commercialization of the VMD module. For the thermal performance test, the experimental equipment of capacity of 2 m3/day was constructed. The permeate flux test and thermal performance test according to feed water conditions such as temperature and flow rate were conducted. The VMD module used in the study was manufactured by ECONITY Co., LTD with PVDF hollow fiber membrane. As a result, the Performance Ratio (PR) of the VMD module showed the maximum value of 0.904 under the condition of feed water temperature of 75℃ and flow rate of 8 m3/h. PR value of the VMD module using PVDF hollow fiber membrane showed linearly increasing relationship with feed water temperature and flow rate. Also, The permeate flux of the VMD module was analyzed to have maximum value of 18.25 LMH and the salt rejection was 99.99%.
        4,000원
        1 2 3