서울시와 같은 도심지의 경우 상수도관, 하수관, 가스관, 통신․전기선과 같은 인프라 시설물을 도로포장 하부에 매설하고 있다. 그 러나 도로 지하에 각종 시설물을 매설하거나 유지보수 등으로 인해 노면을 굴착할 경우, 포장체 구성에 불연속면을 생성하여 이에 대 한 복구가 적절하지 않았을 경우 지반침하, 포장 노면 균열, 평탄성 불량 등의 발생으로 도로 이용자의 승차감 저하 및 노면배수 불량 으로 인한 차량 주행의 안전성 저하, 보도의 경우 통행인의 불편 초래 및 안전사고를 유발할 수 있다. 그러나 현재 서울시의 도로굴착복구 공사는 도로 이용자의 편의를 위해 당일 굴착·당일 복구를 원칙으로 하고 있으며, 이를 위해 주 간 공사 및 장시간 교통통제를 지양하고 있어, 하루 중 야간 8시간 정도로 공사 시간이 부족하고 수많은 공사가 산발적으로 시행됨에 따라 관리 감독이 어려워 시공 품질관리가 미흡하며, 특히 지하 매설물 공사 이후 포장층 하부의 되메우기 공정은 다짐 작업이 제대 로 이루어지지 않는다. 일반적으로 서울시 도로굴착복구 공사는 공사 당일 임시포장을 시행하고, 일정 기간 경과 후 차로 단위로 항구 포장 복구를 시행하고 있으며, 이로 인한 도로 평탄성 불량으로 소음․진동 발생 및 포장 조기 파손의 원인으로 작용하고 있다. 특히 되메우기 공정의 경우, 현행 시방서에 따르면 신속한 되메움 복구 및 관로 주변의 조밀한 충진을 목적으로 관로 주변을 양질의 모래로 시공하는 것을 원칙으로 하고 있으나, 기존 되메움 재료인 모래는 결속력이 약해 인접 구간 공사 시 세굴로 인한 사고 발생 위험 요소를 내재하고 있으며, 누수에 의한 세굴 발생시 편토압 등으로 인해 주변 지반의 침하 등 2차 파손을 발생시킬 수 있다.

The cultural heritage of fortresses is often exposed to external elements, leading to significant damage from stone weathering and natural disasters. However, due to the nature of cultural heritage, dismantling and restoration are often impractical. Therefore, the stability of fortress cultural heritage was evaluated through non-destructive testing. The durability of masonry cultural heritages is greatly influenced by the physical characteristics of the back-fille material. Dynamic characteristics were assessed, and endoscopy was used to inspect internal fillings. Additionally, a finite element analysis model was developed considering the surrounding ground through elastic wave exploration. The analysis showed that the loss of internal fillings in the target cultural heritage site could lead to further deformation in the future, emphasizing the need for careful observation.

This study investigated the seismic performance of reinforced concrete (RC) wall-slab frames with masonry infills. Four RC wall-slab frames with or without masonry infill were tested under cyclic loading. The RC frames were composed of in-plane and out-of-plane walls and top and bottom slabs. For masonry infill walls, cement bricks were stacked applying mortar paste only at the bed joints, and, at the top, a gap of 50 mm was intentionally left between the masonry wall and top RC slab. Both sides of the masonry walls were finished by applying ordinary or fiber-reinforced mortars. The tests showed that despite the gap on top of the masonry walls, the strength and stiffness of the infilled frames were significantly increased and were different depending on the direction of loading and the finishing mortars. During repeated loading, the masonry walls underwent horizontal and diagonal cracking and corner crushing/spalling, showing a rocking mode inside the RC wall-slab frame. Interestingly, this rocking mode delayed loss of strength, and as a result, the ductility of the infilled frames increased to the same level as the bare frame. The interaction of masonry infill and adjacent RC walls, depending on the direction of loading, was further investigated based on test observations.

최근 경주지진과 포항지진 피해사례에서 보이듯 조적벽체 구조물의 붕괴 위험이 사회적으로 큰 주목을 받고 있다. 본 연구는 수평하중에 대한 강성이 구조적으로 취약한 조적벽체 구조물에 대하여 개선된 보강재 설계 및 이를 통한 구조성능 평가를 수행하였다. 선행기술에서 제시한 FRP Plate 보강재의 경우 외부 부착 시 계면 부착파괴에 의한 보강성능 저감이 발생하는 것을 고려하여 본 연구에서는 사전제작 매립형 T-Joint BFRP 보강재를 개발하였으며, 이를 혼합 에폭시계 연성페인트와 혼합 하여 보강 구조물의 마감효과 및 에너지흡수성능을 개선하는 방법으로 제안하였다. 실험 결과, 보강 시험체의 강성은 약 1.37배, 에너지소산능력은 약 2.59배 개선됨을 확인하였다.

Pores produced by carbonization in bulk graphite process degrade the mechanical and electrical properties of bulk graphite. Therefore, the pores of bulk graphite must be reduced and an impregnation process needs to be performed for this reason. In this study, bulk graphite is impregnated by varying the viscosity of the impregnant. The pore volume and pore size distribution, according to the viscosity of the impregnant, are analyzed using a porosimeter. The total pore volume of bulk graphite is analyzed from the cumulative amount of mercury penetrated. The volume for a specific pore size is interpreted as the amount of mercury penetrating into that pore size. This decreases the cumulative amount of mercury penetrating into the recarbonized bulk graphite after impregnation because the viscosity of the impregnant is lower. The cumulative amount of mercury penetrating into bulk graphite before impregnation and after three times of impregnation with 5.1cP are 0.144 mL/g and 0.125 mL/gm, respectively. Therefore, it is confirmed that the impregnant filled the pores of the bulk graphite well. In this study, the impregnant with 5.1 cP, which is the lowest viscosity, shows the best effect for reducing the total pore volume. In addition, it is confirmed by Raman analysis that the impregnant is filled inside the pores. It is confirmed that phenolic resin, the impregnant, exists inside the pores through micro-Raman analysis from the inside of the pore to the outside.

Spring kimchi cabbage was stored fresh for 90 days in a commercial cold storage house. It was sanitized by spraying fungicide on the field before harvesting. The plastic boxes of spring kimchi cabbage were put on the pallet, covered with a 40-hole film, then stacked in the cold storage room at once. The room was maintained for 90 days at 0.7oC after cooling gradually at 2 oC/day. After 90 days, the weight loss was 4.73% and the total trimming loss was 8.26%. The weight loss was 8.08% and the net trimming loss was 3.26% after 90-day storage with partial stack cooling at 2.7oC covered with a 56-hole film. The quality of spring kimchi cabbage after 90-day storage was fresh without physiological disorders.

봄배추를 실용규모의 저장고에서 90일 간 신선하게 저장하였다. 봄배추 춘광 을 수확 1일 전에 노지에서 락스와 테 브코나졸 혼합약제를 살포하여 소독하 고 플라스틱 상자에 담에 팰릿에 적재 한 다음, 40공 타공 비닐로 씌워 저장 고에 일시에 채우고 1일 2℃씩 냉각하 여 0.7℃에서 90일간 저장한 결과 중 량감소율 4.73%, 총정선손실률 8.26%로서 총저장손실률이 12.6%였 다. 그리고 팰릿 포장한 배추를 7일간 5회 분할하여 저장고에 채우고 56공 타공 비닐로 씌워서 바로 2.7℃로 냉각 하여 90일간 저장한 결과 중량감소율 8.08%, 순정선손실률 3.26%로서 순 저장손실률은 11.1%였다. 이때 저장 한 봄배추는 생리장해가 발생하지 않 았고 90일차에도 품질이 신선하였다.

Lightly reinforced concrete (RC) moment frames may suffer significant damage during large earthquake events. Most buildings with RC moment frames were designed without considering seismic loads. The load-displacement response of gravity load designed frames could be altered by masonry infill walls. The objective of this study is to investigate the load-displacement response of gravity load designed frames with masonry infill walls. For this purpose, three-story gravity load designed frames with masonry infill walls were considered. The masonry infilled RC frames demonstrated larger lateral strength and stiffness than bare RC frames, whereas their drift capacity was less than that of bare frames. A specimen with a partial-height infill wall showed the least drift capacity and energy dissipation capacity. This specimen failed in shear, whereas other specimens experienced a relatively ductile failure mode (flexure-shear failure).

The purpose of this study is to make a generalized analytical based on the proposed experiments on reinforced concrete(RC) partially infilled frames by U-type precast concrete(PC) wall panels with openings. RC frame and PC wall panels were connected with different strengths. Therefore, we developed modified strut-tie model(STM) with two seismic retrofitting specimens and conducted a nonlinear analysis by using a computer analysis program. Based on the test results, truss member of modified STM was designed, applying the strut-tie model theory of ACI 318M-11 Appendix- A. As a result, the modified STM analysis results were very similar to the experimental results. As a result of the load-displacement curve comparison, the failure load were similar within 5∼17% of error range. In particular, the experimental results and the results of modified STM analysis show that the failure behavior almost matched.

Cyclic loading test was performed on the partially infilled reinforced concrete(RC) frames by L-type precast concrete(PC) wall panels with the connections of two different strength. Based on the results of experimental test, the nonlinear analysis was practiced with modified strut-tie model(STM) method by using a computer program. Truss member of modified STM was designed, applying the strut-tie model theory of ACI 318M-11 Appendix-A. Modified STM was designed with two ways according to the test result. PC wall panel and RC frame were assumed to composite when push loading applied. The PC and RC structures were also assumed to behave non-composite and those two structures connected with link(top connector) when pull loading applied. The connection was designed by using elastic link of program. The results of analytical modified STM process generally conform to the experimental results. The failure load and the failure mode of the specimens could be predicted using modified STM. The ratio of failure load measured in specimens to analytical values were between 0.83∼1.16. The member or connection which was failed in experiment yield in the results of modified STM. The failure mode perfectly matched.

When reinforcing an existing reinforced concrete beam-column building with a precast concrete panel, special connection between the PC member and the RC member is required to solve the time dependent deformation of the RC member and to receive the large shear forces. The aim of this study is to obtain the shear strength of upper connection between the existing RC beam-column and infilled PC wall panels in experimentally and theoretically. Thus, the static shear loading tests were conducted on the 6 specimens with the plate connection. Shear failure was resulted from the weakest portion of interior PC panel, exterior RC, and the connection, when the PC portion which located at the center of specimen was pulled upward from the bottom. T he experimental result was compared with analytical result from ACI 318M-14 Chapter 17 for the shear strength of post-installed anchor and PCI Handbook 7th edition 6.8 Structural Steel Corbel (PCI Design Handbook 7th edition, 2010) for the strength of cast-in H-beam. The analytical and experimental results show final failure at the same location. The failure loading of experiment showed larger than average 6% to that of the analysis.

This report offers an economically reasonable seismic reinforcement to non-seismic mid/low reinforced concrete structures. Installed a slit in between the reinforced concrete frame and masonry infilled wall then inserted twist bar to prevent inversion and attached to the lower/upper beam. Confirmed the seismic reinforcement effect through static loading test. Total of 4 specimens were produced for the test, a masonry infilled wall without seismic reinforcement and with seismic slit or twist bar applied. As a result, applying the seismic slit and twisted bar was economically reasonable and seismic reinforcement effect was confirmed by showing stable failure, increase of maximum strength and yield displacement, increase of accumulated energy dissipation.

Three-dimensional(3D) display technique is widely used in our daily life. Especially, to product augmented game contents which can interact with users, it is necessary to get high quality resolution image data to reconstruct 3D model more exquisitely. In this paper, we tried to expand depth image captured by Kinect using various interpolation methods(nearest neighbor, bilinear, bicubic) to adapt it to the size of original Kinect color image. To measure the quality of expanded depth image compared to original depth image, we used PSNR(Peak Signal-to-noise ratio) index. Besides, we implemented GPU parallel processing algorithm with OpenCL to interpolate a large amount of image data rapidly. As a result of the experiment, a bicubic interpolation method made an accurate depth image although it had a long time.

본 논문에서는 범용유한요소해석 프로그램인 ABAQUS를 사용하여 국내에서 사용되는 콘크리트벽돌을 조적채움벽으로 가진 철근콘크리트 골조를 대상으로 유한요소해석을 실시하였다. 해석대상은 순수골조, 채움벽의 두께가 0.5B인 골조, 두께가 1.0B인 골조의 3종류이다. 철근콘크리트 골조 및 채움벽의 재료특성은 재료시험 결과로부터 구하였으나 두께가 1.0B인 채움벽의 경우 벽돌의 쌓기방법의 차이에 의해 0.5B 두께의 실험체보다 4배 정도 증가된 인장강도를 사용하였다. 유한요소해석결과는 실험을 통해 구한 하중-변위관계 및 변위각에 따른 균열양상을 상당히 정확하게 예측하였다. 유한요소해석 결과의 분석을 통해 조적채움벽과 골조사이의 접촉응력 및 골조의 전단력과 휨모멘트를 산정하였다.

본 연구에서는 저층 조적채움벽 철근콘크리트 골조 구조물의 내진보강 전과 후에 대하여 강제 진동 실험과 상시 진동 계측을 수행하였으며 시스템 식별과정을 통하여 구조물의 동특성을 구하고 해당 구조물과 유사한 동특성을 보이는 해석 모델을 만들었다. 시스템 식별 결과 댐퍼가 설치된 x방향의 감쇠비가 증가되었으며, 해석 모델과 비교한 결과 추가 설치된 부재들(전단벽과 댐퍼)의 유효 강성은 부재의 총단면 강성의 50%만이 발현되어 해당 부재들이 기존의 구조물이나 부재와 완전히 일체화되지는 않음을 알 수 있었다. 또한, 추가 설치된 기초의 y방향 구속조건을 핀으로 하여야 동특성을 일치시킬 수 있었는데, 이는 새로운 기초가 설치되며 해당 지질의 특성이 변화되었기 때문으로 보인다.