We have demonstrated the production of thin films containing multilayer graphene-coated copper nanoparticles (MGCNs) by a commercial electrodeposition method. The MGCNs were produced by electrical wire explosion, an easily applied technique for creating hybrid metal nanoparticles. The nanoparticles had average diameters of 10–120 nm and quasi-spherical morphologies. We made a complex-electrodeposited copper thin film (CETF) with a thickness of 4.8 μm by adding 300 ppm MGCNs to the electrolyte solution and performing electrodeposition. We measured the electric properties and performed corrosion testing of the CETF. Raman spectroscopy was used to measure the bonding characteristics and estimate the number of layers in the graphene films. The resistivity of the bare-electrodeposited copper thin film (BETF) was 2.092 × 10–6 Ω·cm, and the resistivity of the CETF after the addition of 300 ppm MGCNs was decreased by 2% to ~2.049 × 10–6 Ω·cm. The corrosion resistance of the BETF was 9.306 Ω, while that of the CETF was increased to 20.04 Ω. Therefore, the CETF with MGCNs can be used in interconnection circuits for printed circuit boards or semiconductor devices on the basis of its low resistivity and high corrosion resistance.

구형 충격을 받는 필름 코팅된 유리 시스템의 거동을 개발한 유한 요소 프로그램에 의하여 연 구하고자 한다. 충격 거동을 예측하기 위하여 Sun의 higher order beam theory와 Kurapati의 generalized power law와 연계한 새롭고 효과적인 동적 유한 요소법을 제안한다. 필름 코팅된 유리 시 스템과 모놀리식 유리에 대하여 접촉력, 변형량, 운동에너지, 속도 및 응력 등을 계산한 후 결과를 비교 검토하여 코팅 시스템의 필름이 충격 손상을 방지하고 충격 저항이 우수하다는 것을 정성적 및 정량적으로 규명하였다.

A microencapsulated cinnamon oil (CO)-coated film was developed using a pilot-plant scale film coating system. CO microencapsulated with polyvinyl alcohol was incorporated with a printing ink and the ink mixture was applied to the surface of a polypropylene (PP) film as an ink coating using a gravure printing press at a speed of 20-200 m/min. The tensile strength, percentage elongation at break, elastic modulus, and water vapor permeability of the PP films with and without coating with the microcapsules were not significantly different (p > 0.05), which indicates that the coating did not alter those properties of the films. Microencapsulation effectively prevented the volatilization of CO in the films. The microencapsulated system may be extended to other food-packaging films for which the same ink-printing platform is used. The results from this study imply that the oil-microencapsulated films could be potentially produced by a modern film manufacturing system.

TiO2 thin films consisting of positively charged poly(diallyldimethylammonium chloride)(PDDA) and negatively charged titanium(IV) bis(ammonium lactato) dihydroxide(TALH) were successfully fabricated on glass beads by a layer-by-layer(LBL) self-assembly method. The glass beads used here showed a positive charge in an acid range and negative charge in an alkaline range. The glass beads coated with the coating sequence of(PDDA/TALH)n showed a change in the surface morphology as a function of the number of bilayers. When the number of bilayers(n) of the(PDDA/TALH) thin film was 20, Ti element was observed on the surface of the coated glass beads. The thin films coated onto the glass beads had a main peak of the (101) crystal face and were highly crystallized with XRD diffraction peaks of anatase-type TiO2 according to an XRD analysis. In addition, the TiO2 thin films showed photocatalytic properties such that they could decompose a methyl orange solution under illumination with UV light. As the number of bilayers of the(PDDA/TALH) thin film increased, the photocatalytic property of the TiO2-coated glass beads increased with the increase in the thin film thickness. The surface morphologies and optical properties of glass beads coated with TiO2 thin films with different coating numbers were measured by field emission scanning electron microscopy(FE-SEM), X-ray diffraction(XRD) and by UV-Vis spectrophotometry(UV-vis).

Ultra-thin aluminum (Al) and tin (Sn) films were grown by dc magnetron sputtering on a glass substrate. The electrical resistance R of films was measured in-situ method during the film growth. Also transmission electron microscopy (TEM) study was carried out to observe the microstructure of the films. In the ultra-thin film study, an exact determination of a coalescence thickness and a continuous film thickness is very important. Therefore, we tried to measure the minimum thickness for continuous film (dmin) by means of a graphical method using a number of different y-values as a function of film thickness. The raw date obtained in this study provides a graph of in-situ resistance of metal film as a function of film thickness. For the Al film, there occurs a maximum value in a graph of in-situ electrical resistance versus film thickness. Using the results in this study, we could define clearly the minimum thickness for continuous film where the position of minimum values in the graph when we put the value of Rd3 to y-axis and the film thickness to x-axis. The measured values for the minimum thickness for continuous film are 21 nm and 16 nm for sputtered Al and Sn films, respectively. The new method for defining the minimum thickness for continuous film in this study can be utilized in a basic data when we design an ultra-thin film for the metallization application in nano-scale devices.

목적: 전면이 평면인(γ=∞) 하드코팅 된 렌즈에서 코팅박막의 두께와 굴절률을 박막의 손상없이 측정한다. 방법: He-Ne 레이저를 박막에서 도파되도록 렌즈로 집속시켜 Gadoliniun Gallium Garnet(G.G.G.) 프리즘에 입사시키고 입사된 광의 고유모드 중 일부가 도파관을 새어나가서 m차 line(m은 정수)으로 관측되도록 장치하였다. 이 line들 사이의 떨어진 거리를 광 검출기로 측정하는 prism-film coupler 방법으로 실험하였다. 결과: TE(transverse electric) mode에서 박막두께는 약 2.42 ㎛, TM(transverse magnetic) mode에서는 약 2.55 ㎛로 평균 약 2.49 ㎛로 측정되었고, 굴절률은 두 mode에서 약 1.60으로 같은 값을 얻었다. 결론: 이 값(2.49 ㎛)은 전자현미경(SEM)으로 측정한 두께와는 5.5%의 오차를 나타냈다.

Ultraviolet curable coating solution was prepared with poly(ethylene glycol) acrylate oligomer and various mono and multi-functional acrylate monomers. The optical properties of UV cured coating layer on PET film with acrylate coating solution containing metal oxides, such as fumed silica and alumina, were also investigated to reduce light reflection on films. Poly(ethylene glycol) diacrylate which has 575 of average molecular weight was used as oligomer acrylate, and pentaerythritol triacrylate and dipentaerythritolpenta-/hexa acrylate were used as multi-functional acrylate monomers. Also, butyl acrylate was used to improve the adhesion as well as to reduce glass transition temperature to give a better flexability. 1-hydroxy cyclohexyl phenyl ketone was used as photoinitiator. We found out the metal oxides in acrylate coating solution showed a homogeneous dispersion from energy dispersive spectroscopy data. Transmittance and light reflection of coated PET film was measured with UV/vis spectrometer and gloss meter, respectively. When 1.00 g of both metal oxides was added into coating solution, the transmittance and the glossiness were reduced from 90% to 30% and from 190 GU to 35 GU, respectively. However, adding up to 1.00 g of the metal oxide into coating solution did not affect on the hardness of coating layer and adhesion between coated layer and PET film. Conclusively, we can control transmittance and light reflection of coated film by adjusting the amounts of metal oxide in coating solution.

The surface of poly(ethylene naphthalate) film applicable to high temerature insulator for convection microwave oven was modified with silicone coating solutions in the presence of silane crosslinking agent. The structure and properties of the PEN films were investigated by using Fourier transform IR spectroscopy, viscometry, microscopy, and tensile tests. The experimental results showed that the coating with silicone enhanced thermal stability up to 200℃, and slightly lowered the tensile strength and elongation of the PEN films. Judging from dimensional stability results the silicone coated PEN films can not be used for higher temperature insulator above 230℃. Serious dimensional contraction of films was obtained during heat treatment at 250℃ even for 1h. However, the surface of those films still have same chemical structure of silicones. Therefore, If we use PEN film prestretched at 230℃ as base one it will be possible to prepare a high temperature insulator up to 230℃. Conclusively, a silicone coated PEN film can be suitable for the application to convection microwave oven door insulator at high temperature up to 230℃.

현재 전기, 전자, 우주, 자동차, 무기 등의 여러 분야에서 응용되고 있는 TaNx 다층박막저항체의 특성을 개선하기 위하여 magnetron sputtering법으로 TaNx박막을 제조한 후, 온도와 질소분압에 따른 전기저항 및 TCR특성 변화를 조사하였고, 미세조직이 이들 전기적 성질에 미치는 영향을알아보기 위해 상분석과 morphology를 관찰하였다. 그 결과, TaNx을 코팅한 박막의 전기저항은 N2Ar이 0.4 이상에서, 금속전도특성에서 이온전도특성으로 변화하였으며,Cr이 TCR효과를 안정시키는 역할은 하여 TaNx/A I2 O3보다 TaNx/Cr/A i2 O3박막의 TCR특성이 더 안정하게 나타났다. 또한 TaNx/A I2 O3박막과 TaNx/Cr/A i2 O3박막의 경우 모두 N2/Ar이 0-0.4정도에서 TCR효과에 좋은 특성을 나타내었다. X-선회절 실험 결과 N2/Ar비가 1일 경우에 T a2 N.8이 생성되었고, 분압이 증가함에 따라 비정질이 생성되었다. morphology가 N2/Ar이 증가함에 따라 입자의 모양이 불연속아일랜드 형태로 변화하였으며, 이것은 질소분압에 따른 전기저항 변화와 일치하였다.다.

The purpose of this study was to identify for extenders, adhesives, colorants, and fungicides suitable for the production of high-quality film-coated seeds of Chinese cabbage. In addition, the effect of various additives used for film coating on the germination of coated seeds and seedling vigor was investigated to establish appropriate treatment conditions for film coating efficiency. The germination rate and germination speed in Chinese cabbage film-coated seeds did not differ significantly depending on the type and concentration of the extender, while the use of Talc resulted in superior granulation capacity and adhesion of the seed coat in comparison to Zeolite. There was no significant difference in the germination rate depending on the type of adhesive used for film coating of Chinese cabbage seeds, but the germination rate was slightly slower in the film-coated seeds using carboxymethyl cellulose as an adhesive. On the other hand, the seeds coated with a film using 1% PVA as an adhesive not only maintained hardness enough to withstand external pressure, but also showed a high germination rate. In addition, the suitable disinfectant for film coating was venoram, and the treatment concentration was good at 250 mg·L-1. The type of colorant used in the film-coated seeds of Chinese cabbage did not significantly affect the germination rate, germination speed, and seedling vigor. The seeds film-coated using the liquid colorant were superior in appearance to the seeds film-coated with the solid colorant, which implies the possibility of reduction in the manufacturing costs by using the water-soluble paints as colorants for film-coated seeds.

천연 항균성 peptide인 polylysine을 이용한 항균성 포장재의 개발을 위한 기초자료를 얻기 위하여 polyamide 수지를 기반으로 하는 제조조건을 검토하고 두부를 대상식품으로 하여 병원성 및 부패 관련 미생물에 대한 항균활성을 확인하였다. Polylysine 제조조건에 있어서는 polylysine, polyamide의 농도와 코팅필름의 두께에 따라 항균활성에 큰 차이를 보였으나, 이상의 polylysine, polyamide,

The film coated snap bean (Phaseolus vulgaris) seeds with five different coating materials treated with 3% increase in seed weight were planted at sandy loam soil controlled moisture content of 18, 19, 20 and 21 %. The oxygen diffusion rate (ODR) was calculated from the different moisture content soil. The number of normal seedlings, seedling vigor, and seedling capability in field (seed vigor x dry matter weight) were observed at 9 days after planting and compared to the changes of ODR. The germination rate and ODR were sharply decreased simultaneously in the seeds planted at 21 % soil moisture content. Seedling emergence did not occur at all as the soil moisture content increased above 22 %. Hence this value should be considered as the threshold of soil moisture content for seedling emergence. An ODR value under 20% did not influence the percent emergence significantly. The certain difference observing in the emergence at the same ODR was not related clearly to the condition of soil. So it can be assumed that the limit of soil moisture content for the emergence of snap bean was approximately 20%. The value of 18% soil moisture content may be considered as the optimum for snap bean emergence. There was close relationship between the mean value of ODR in different soil moisture contents and the emergence. The germination rates of the seeds coated with the different materials were quite different when the seeds were planted at 21 % soil moisture. Dry weight of the seedlings from film coated seeds was decreased slightly, but the germination rates were not much different from the non-treated control under relatively higher soil moisture content (21 %). Major factor lowering emergence rate was oxygen stress while film coating act as a minor constraint for snap bean sown in excess soil moisture condition.

The quality changes of strawberries packaged using low density polyethylene (LDPE) film filled with 3% silver-coated ceramic (WC30) and filled with it and 0.1% chitin (CWC) were investigated during storage at 2 for 5 days. In gas composition within film bag, CWC and WC30 kept higher CO2 concentration than LDPE without silver-coated ceramic and chitin (CO) did during 5 day storage. The weight loss of strawberries during storage was the smallest in WC30 and the largest in CWC in 5 days. Hardness of strawberries was the highest in WC30 and the lowest in CO during 5 day storage. pH of strwberries was increased a little until 1 day and was not changed after 1 day storage, and soluble solid content was not changed during storage. Vitamin C content was decreased significantly until 2 day storage and decreased a little after 2 days. There is no differences in the change of vitamin C content among the packaging materials. In color measurement, lightness was the highest in WC 30 and in sensory evaluation, all characteristics also had the highest scores in WC30. In conclusion, better quality of straberries was shown in WC30 than in CWC and CO during storage.