바이오산업의 발전으로 의약품, 식품 등의 생산 과정의 분리/정제 공정에 사용되어 왔던 기존의 컬럼 크로마토그 래피를 대체하여 더 높은 처리효율을 갖는 막 크로마토그래피가 부상하고 있다. 본 연구에서는 서로 다른 기공 크기의 두 가 지 상용 셀룰로오스 아세테이트(Cellulose acetate, CA) 분리막을 탈아세틸화 과정을 통해, 리간드의 개질이 용이한 다공성 재 생 셀룰로오스 지지체를(Regenerated cellulose, RC) 제조하였다. 음이온 교환능을 부여하고자 grafting을 수행하였으며, 구체 적으로는 UV 중합법을 통해 4차 암모늄을 포함하는 음이온 교환 리간드(MAPTAC)를 부착하여 음이온 교환용 흡착막을 제 조하였다. 단백질 흡착 용량은 정적 흡착 용량(Static binding capacity, SBC)시험을 통해 총 단백질 흡착 용량을 측정했고, 동 적 흡착 용량(Dynamic binding capacity, DBC)을 측정하여 상용막과 비교 평가하였다. 성능 평가 결과 단백질 흡착량은 넓은 표면적에 의해 리간드 밀도가 높은, 기공 크기가 작은 순서로 높게 측정되었고, 상용 CA분리막을 탈아세틸화하고 리간드를 부착시킨 분리막(RC 0.8 + MAPTAC 43.69 mg/ml, RC 3.0 + MAPTAC 36.33 mg/ml)이 상용 막 크로마토그래피 제품(28.38 mg/ml) 대비 높은 흡착 용량을 보였다.

Radioactive waste containing cellulosic materials such as cotton, paper and wood are being disposed in Low-and intermediate-level radioactive waste disposal site in Gyeongju. Cellulose has recently emerged great issue in terms of disposal site safety as it can be decomposed into an organic complex compound, ISA (isosaccharinic acid), under strong alkali conditions (pH 12.5 or higher) formed by the hydrated cement, to accelerate the mobility of the radionuclides in the disposal facility. However, in Korea, there are insufficient criteria for confirming the suitability for disposal of low-and intermediatelevel radioactive wastes including cellulose, and there is no specific method for evaluating the total amount of waste to confirm the suitability of disposal. Therefore, the method of SKB (Swedish Nuclear and Fuel Management Company), which has established acceptance criteria related to the physicalchemistry safety of cellulose, is analyzed to suggest a method for deriving the amount of cellulosecontaining waste disposal. Cellulose, an organic complexing agent, is an important consideration for safety case at the Swedish low-and intermediate-level radioactive waste disposal site SFR. SKB calculated the amount of cellulose generated by separately labeling cellulose-containing wastes of 1-2BMA, Silo and 1BTF (SKB 2013). BLA, a low-level radioactive waste disposal facility, is not considered due to its low radionuclide inventory (~0.2% of SFR’s total radionuclide inventory, SKB 2013). To calculate the amount of cellulose that can be disposed of, information on the mass and volume of hydrated cement (concrete waste, cement solidification waste, disposal container, grouting, disposal shed), the concentration of ISA absorbed in the hydrated cement, and the concentration of ISA dissolved in the groundwater which were used. In addition, the total disposable amount was calculated using the cellulose degradation rate, composition ratio, and the cellulose containing waste volume.

With the aim to fabricate flexible, mobile, and low-energy powered electronics, laser treatment of paper-based materials from carbon, cellulose, and natural products may be viable as one of the strategies to achieve this objective as it potentially provides a sustainable and precise patterning of a graphene-based circuit for various emerging electronic applications, such as sensor, robot, energy, and memory devices. Irradiation of high-energy beam for induction of porous-rich graphene or reduction of graphene oxide is easily accomplished from a commercially available laser machine with various laser sources, power, and pulse number setting. Moreover, the process itself can easily be adapted in the various manufacturing sectors due to the technology’s maturity status and its ability to be computer programmed. In comparison to environmental-benign polymer, the selection of paper as a substrate for electronics may introduce a new idea into the design possibility of electronic devices since the paper is not only thin, lightweight, biodegradable, and mechanically stable, but is also able to be assembled into another form and shape simply by traditional origami and kirigami technique for many applications. Here, in this work, recent laser processing strategies for the preparation of graphene either from graphitization of cellulose or deoxygenation of graphene oxide for green electronics are reviewed with brief coverage of the deposition technique of graphene oxide paper prior to laser annealing and discussion on the emerging relevant electronics field that benefitted greatly from the laser-assisted fabrication. To conclude the literature study, a remaining challenge, and prospective outlooks of laser writing of graphene on paper are also highlighted.

This study was carried out to examine the physical characteristics of bacterial cellulose (BC) and its optimal culture condition using coffee by-products. Recently, recycling resources and employing eco-friendly materials have been raised as significant issues in the food industry. As the coffee industry develops, interests and efforts for recycling coffee wastes are also growing. This study attempted to confirm the production of BC by utilizing spent coffee grounds filtrate as a medium. In order to confirm the optimal culture conditions for BC production, different culture methods, initial pH, culture temperature, and culture period were examined. The optimal pH and temperature were 6.0 and 30oC, and the optimal culture period was 14 days. The cultivated BC was dried by hot air drying, freezedrying, and mold drying, respectively. Then, the properties of the BC films, such as tensile strength, elongation, water-solubility, thickness, and chromaticity were compared. The drying method affected the shape and structure of the final BC films. The production of BC film is expected to expand opportunities for recycling coffee by-products and contribute to solving environmental problems caused by food waste.

Recently, concern regarding disposal of cellulosic material is growing as cellulose is known to produce complexing agent, isosaccharinic acid (ISA), upon degradation. ISA could enhance mobility of some radionuclides, thus increasing the amount of radionuclide released into the environment. Thus, evaluation on the possible impact of the cellulose degradation would be an important aspect in safety evaluation. In this paper, safety assessments conducted in Sweden and UK are studied, and the factors required to be considered for appropriate safety assessment of cellulose is analyzed. SKB (Sweden) conducted safety assessment of cellulose degradation as a part of long-term safety assessment of SFR. SKB determined that ISA would impact sorption of trivalent and tetravalent radionuclides (Eu, Am, Th, Np, Pa, Pu, U, Tc, Zr and Nb) at concentration higher than 10−4–10−3 M, and impact sorption of divalent radionuclides (Ni, Co, Fe, Be and Pb) at concentration higher than 10−2 M. Then, SKB conservatively set the upper limit of ISA concentration to be 10−4 M and conducted cellulose degradation evaluation on each waste package type, considering the expected disposal environment of SFR. Based on the calculated results, some of the waste packages showed concentration of ISA to be higher than 10−4 M, so SKB conservatively developed waste acceptance criteria to prevent ISA being produced to an extent of affecting the safety of the repository. SKB conducted safety assessment only for the repositories with pH above 12.5 and excluded 1BLA from the safety assessment as the expected pH of 1BLA is around 12, which is insufficient for cellulose to degrade. However, SKB set disposal limit for 1BLA as well, to minimize potential impact in future. Serco (UK) conducted safety assessment of cellulose degradation for the conceptual repository, which is a concrete vault with cementitious backfill. Serco estimated that the pH of repository would maintain around 12.4. Serco conservatively assumed that the pH would be sufficient for cellulose degradation to occur partially, and suggested application of appropriate degradation ratio for safety assessment of cellulose degradation. To conduct appropriate safety assessment of cellulose degradation, an appropriate ISA concentration limit based on radionuclide inventory list, and an appropriate cellulose degradation ratio based on the pH of disposal environment should be determined. As for guidance, below pH 12.5, cellulose degradation is not expected, and between pH 12.5–13, partial cellulose degradation is expected. In future, this study could be used as fundamental data to evaluate safety of the repository.

Recently, concern regarding disposal of cellulosic material is growing as cellulose is known to produce complexing agent, isosaccharinic acid (ISA), upon degradation. ISA could enhance mobility of some radionuclides, thus increasing the amount of radionuclide released into the environment. Evaluation on the possible impact of the cellulose degradation would be an important aspect in safety evaluation. In this paper, the maximum safe disposal amount cellulose is evaluated considering the disposal environment of silos of 1st phase disposal facility. The key factor governing the impact of cellulose degradation is pH of disposal environment, as cellulose is known to degrade partially at pH above 12.5, and completely at pH above 13. Thus, disposal environment should be analyzed as to determine the extent of degradation. As silos are constructed with large amount of cement, porewater within concrete walls would be of very high pH. However, for high pH porewater to be released into the pores of crushed rock, which is filling up the silos, lower pH groundwater (commonly pH 7) should flow into the silos through the concrete walls. This causes dilution of the high pH concrete porewater, resulting in a lower pH as the silos are filled, reaching to expected pH of 11.8–12.3, which is below cellulose degradation condition. Thus, cellulose degradation is not expected, but to quantitatively evaluate safe disposal amount of cellulose, partial degradation is assumed. Upon literature review, the most conservative ISA concentration, enhancing radionuclide mobility, is determined to be 1.0×10−4 M and to reach this concentration, cellulose mass equivalent to 6wt% of cement of the repository, is required to be degraded. However, this ratio is derived based on complete degradation of cellulose into ISA, so for partial degradation, degradation ratio and yield ratio of ISA should be considered. Commonly, cellulosic material (e.g. cotton, paper, etc.) has degree of polymerization (DP) between 1,000–2,000, and with this DP, degradation ratio is estimated to be about 10%. Furthermore, yield ratio of ISA is known to be 80%. Considering all these aspects, about 1.79×107 kg of cellulose could be disposed, which if converted into number of drums, considering cellulose content of dry active waste, more than 100,000 drums (200 L) could be disposed with negligible impact on safety. Based on the result, negligible impact of cellulose degradation is expected for safety of 1st phase disposal facility. In future, this study could be used as fundamental data for revising waste acceptance criteria.

It has been discovered that the isosaccharinic acid (ISA) formed in a cellulose degradation leachate were capable of forming soluble complexes with thorium, uranium (IV) and plutonium. Since 1993, the ISA has received particular attention in the literature due to its ability to complex a range of radionuclides, potentially affecting the migration of radionuclides. ISA is formed as a result of interactions between cellulosic materials within the waste inventory and the alkalinity resulting from the use of cementitious materials in the construction of the repository. In an alkaline cementitious environment, cellulose degrades mainly via a peeling-off reaction. The main degradation product is ISA, a polyhydroxy type of ligand forming stable complexes with tri- and tetravalent radionuclides. ISA can have an adverse effect on the sorption of radionuclides to an extent which depends on its concentration in the cement pore water and potentially enhance their mobility. The concentration of ISA is governed by several factors such as cellulose loading, cement porosity, extent of cellulose degradation, etc. The sorption of ISA on cement, however, is the process which governs the concentration of ISA in the pore water. According to the experimental result from a literature, the ISA concentration in facilities with a cellulose loading of 5% is calculated to be of the order of 10−4 M. At this level, the effect of cellulose degradation products on radionuclide sorption is negligibly small. Recently in Korea, cellulous limits as waste acceptance criteria is studying and planning to prepare the detailed requirement for near surface radioactive waste disposal facilities. It is desirable to suggest consideration on cellulose disposal limits around the time that the regulatory body and concern organizations establish the cellulose disposal limits as follows. Firstly, identify the cellulose effect on the sorption of the nuclides as cementitious disposal environments such as affected nuclides, threshold value and contribution to radiological risks under domestic disposal environment. Secondly, make sure and consider the difference between lab-scale experimental conditions and probability occurring in real disposal conditions such as probability for generation and persistence of pH in cellulosic material disposal conditions and cellulosic material disposal methods. Finally, consider characterization of cellulosic material such as polymerization, contents of cellulose in law material and time of degradation process. As a result, desirable cellulose limits are to set up for both safety and economic aspect.

현재 우리 산업의 가속화된 발전으로 인해 다양하고 많은 양의 오염이 만들어지기 시작하고 있다. 특히 폐수의 경우 석유, 금속 및 유기물로 오염되는 강과 바다가 늘고 있으며, 빠른 조치가 필요해 보인다. 이러한 오염에 대응하기 위해 폐수에서 분리막을 이용한 깨끗한 물의 여과가 비용적으로 유리하고 친환경적인 기술로 떠오르고 있다. 재생 자원으로 만들 어진 막여과 기법들이 환경오염의 원인 중 하나인 합성고분자 분리막들을 대체하기 위해 많이 사용되고 있다. 박테리아 셀룰 로오스(Bacterial Cellulose / BC)는 순수하고 뚜렷한 형태의 셀룰로오스 나노섬유(Cellulose nanofibrils / CNF)이다. CNF에서 제조된 나노페이퍼는 각기 다른 용도로 한외여과막과 나노여과막으로 사용된다. BC의 높은 결정성으로 인해 폐수 처리 막의 필수 기준인 우수한 기계적 성질을 가질 수 있다. 본 리뷰 논문에서는 염료, 오일 및 중금속 등 폐수의 오염물질들을 걸러내기 위해 사용될 수 있는 BC 기반 분리막들에 대해 논의한다.

This study investigates the physicochemical and sensory properties of the soy-based patties using κ-carrageenan (CG) and methyl-cellulose (MC) as binders. Soy-based patties were prepared using 0%-2% of κ-carrageenan and methyl-cellulose in proportion, and the quality change of soy-based patties was measured by storing them at 4oC for 4 weeks. During the storage periods, the water holding capacity of ‘MC 1.5%+CG 0.5%’ showed high values. As the MC content increased, the weight loss and cooking loss tended to decrease, and both values increased significantly during the storage period. As the MC content increased, the lightness and redness tended to decreased. The hardness and chewiness of soy-based patties tended to increase as the MC content increased. During the storage period, the total aerobic bacteria and the coliforms tended to increase. The VBN content was showed 14.6-17.5 mg%/100g in first week, since then, the VBN content has continued to increase. As a result of sensory evaluation, the springiness, taste and overall acceptability of soy-based patties with ‘MC 1.5%+CG 0.5%’ and ‘MC 2.0%’ showed the highest value.

After flame-retardant treatment by the two different agents, the thermal behaviors of Lyocell fibers are discussed. In this research, H3PO4 and NaCl reduced the degradation rate and increased the char yield of the Lyocell fibers, and also increased the limiting oxygen index with the char yield increased. After treatment, the integral procedure decomposition temperature and the activation energy of Lyocell fibers are significantly increased by various concentration factors. These phenomena were indicated by the dehydration, rearrangement, formation of carbonyl groups, the evolution of carbon monoxide and dioxide, and carbonaceous residue formation. These effects were indicating the slow pathway of flame retardancy for the Lyocell fibers and are attributed to the two different flame-retardant agent treatments.

An enthalpy exchange element (EEE) is frequently made of papers, and a concern exists on growth of fungus or bacteria. This concern may be eliminated if polymer membrane is used instead of paper. Furthermore, most existing enthalpy exchangers have cross-flow configuration, which yields lower performance than counter-flow one. In this study, a counter-flow enthalpy exchange element was made using PVDF and cellulose composite. Heat and moisture transfer tests were conducted changing the frontal air flow rate from 150 m 3 /h to 350 m 3 /h at both the heating and the cooling condition. Results showed that the temperature efficiencies were approximately the same independent of the weather condition. Humidity efficiencies at the heating condition, however, were higher than those at the cooling condition. Furthermore, the heat transfer coefficients approached the theoretical value as the flow rate increased. In addition, the vapor transmission rates at the heating condition were higher than those at the cooling condition, probably due to the higher humidity efficiency at the heating condition. Future research will be focused on moisture diffusion characteristics of the composite membrane, which requires further measurements of water holdup, equilibrium adsorption curve, etc.