Er을 첨가한 ZnS:Mn 형광체를 1000℃에서 4시간 고상반응법으로 소결하여 제조하였다. 결정 구조 및 광 특성은 XRD, PL 그리고 SEM을 통하여 분석하였다. XRD 결과, ZnS:Mn 형광체는 hexagonal 구조가 나타났고, Er의 농도가 증가함에 따라 Er2O3 구조가 관찰되었다. ZnS:Mn 형광체의 평균입자 크기는 약 15㎛였고, Er 첨가와 함께 ZnS:Mn, Er 형광체의 입자 크기는 감소하였다. 580nm 발광 피크는 ZnS:Mn, Er 형광체에서 Mn2+ 이온의 4T1→6A1으로의 전이에 의한 것이다. Er을 0.5mol% 첨가한 형광체의 발광 세기는 Er을 첨가하지 않은 ZnS:Mn 형광체보다 높았다. ZnS:Mn, Er 형광체에서 발광 세기의 증가는 Er3+에서 Mn2+로의 에너지 전이에 의한 것으로 생각된다.

A SrAl2O4:Eu2+,Dy3+ phosphor powder with stuffed tridymite structure was synthesized by glycine-nitratecombustion method. The luminescence, formation process and microstructure of the phosphor powder were investigated bymeans of X-ray diffraction (XRD), scanning electron microscopy (SEM) and photoluminescence spectroscopy (PL). The XRDpatterns show that the as-synthesized SrAl2O4:Eu2+,Dy3+ phosphor was an amorphous phase. However, a crystalline SrAl2O4phase was formed by calcining at 1200oC for 4h. From the SEM analysis, also, it was found that the as-synthesizedSrAl2O4:Eu2+,Dy3+ phosphor was in irregular porous particles of about 50µm, while the calcined phosphor was aggregated inspherical particles with radius of about 0.5µm. The emission spectrum of as-synthesized SrAl2O4:Eu2+,Dy3+ phosphor did notappear, due to the amorphous phase. However, the emission spectrum of the calcined phosphor was observed at 520nm(2.384eV); it showed green emission peaking, in the range of 450~650nm. The excitation spectrum of the SrAl2O4:Eu2+,Dy3+phosphor exhibits a maximum peak intensity at 360nm (3.44eV) in the range of 250~480nm. After the removal of the pulseXe-lamp excitation (360nm), also, the decay time for the emission spectrum was very slow, which shows the excellent long-phosphorescent property of the phosphor, although the decay time decreased exponentially.

In this study, we fabricated a polymer light emitting diode (PLED) and investigated its electrical and optical characteristics in order to examine the effects of the PFO [poly(9,9-dioctylfluorene-2-7-diyl) end capped with N,N-bis(4-methylphenyl)-4-aniline] concentrations in the emission layer (EML). The PFO polymer was dissolved in toluene ranging from 0.2 to 1.2 wt%, and then spin-coated. To verify the influence of the TPBI [2,2',2"-(1,3,5-Benzinetriyl)-tris(1-phenyl-1-H-benzimidazole)]electron transport layer, TPBI small molecules were deposited by thermal evaporation. The current density, luminance, wavelength and current efficiency characteristics of the prepared PLED devices with and without TPBI layer at various PFO concentrations were measured and compared. The luminance and current efficiency of the PLED devices without TPBI layer were increased, from 117 to 553 cd/m2 and from 0.015 to 0.110 cd/A, as the PFO concentration increased from 0.2 to 1.0 wt%. For the PLED devices with TPBI layer, the luminance and current efficiency were 1724 cd/m2 and 0.501 cd/A at 1.0 wt% PFO concentration. The CIE color coordinators of the PLED device with TPBI layer at 1.0 wt% PFO concentration showed a more pure blue color compared with the one without TPBI, and the CIE values varied from (x, y) = (0.21, 0.23) to (x, y) = (0.16, 0.11).

This research was conducted to assess applicability of photostimulated luminescence (PSL) and Thermoluminescence (TL) methods for investigation of infant and young children products, nut, seasoned dried fish,spice, dried fruits, fruit & vegetable, grain and marine products, which are not approved for irradiation in Korea. PSL results show that the photon counts of non-irradiated samples were lower than 700, while those of irradiated samples were higher than 700. In TL measurement, TL ratio of irradiated samples were higher than 0.1 or ones can decrease below 0.1 whereas the temperature range of TL Glow curve was between 150-250℃. Monitoring result about 8 class of 325 not approved to irradiated foods, photon counts of samples were less than 700, and after re-irradiation TL Ratio (TL₁/TL₂) through re-irradiation step at 1 kGy were higher than 0.1 for the all samples. Therefore, these results suggested that PSL and TL measurements were useful detection methods for 8 class food products not approved to irradiation in Korea and all sample (325 cases) were not irradiated when we analysed by PSL and TL methods.

The thermoluminescent phosphors of LiYSiO4 containing rare earth metal(La) dopants of 1 wt.%5 wt.% were prepared, and their TL characteristics have been investigated as a function of parameters such as the doping level and the heating rate. The grain size and cooling temperature of the highly sensitive LiYSiO4: La phosphors have been investigated. The glow curve of LiYSiO4: La has two peaks (P1, P2), and the peak height ratio of the two peaks is called P2/P1; here, the main peak is P2. Experimental results indicate that the peak height ratios of the glow curve for LiYSiO4: La are clearly correlated with the grain size and cooling temperature. The maximum P2/P1 ratio 3.25, the maximum sensitivity was observed for a grain size between 100-150 μm. The intensity of the TL peak of the phosphors was linearly proportion to the dose of X-rays.

Eu red phosphor was prepared by microwave synthesis. The crystal phase, particle morphology, and luminescent properties were characterized by XRD, SEM, and spectrofluorometer, respectively. The prepared :Eu particles had good crystallinity and strong red emission under ultravioletet excitation. The crystallite size increased with calcination temperature and satuarated at . The primary particle size initially formed was varied from 30 to 450 nm with microwave-irradiation (MI) time. It was found that the emission intensity of :Eu phosphor strongly depends on the MI time. In terms of the emission intensity, it was recommended that the MI time should be less than 15 min. The emission intensity of :Eu phosphor prepared by microwave syntehsis strongly depended on the crystallite size of which an optimal size range was 50-60 nm

ZnO thin film was grown on a sapphire single crystal substrate by plasma assisted molecular beamepitaxy. In addition to near band edge (NBE) emissions, both blue and green luminescences are also observedtogether. The PL intensity of the blue luminescence (BL) range from 2.7 to 2.9eV increased as the amountof activated oxygen increased, but green luminescence (GL) was weakly observed at about 2.4eV without muchchange in intensity. This result is quite unlike previous studies in which BL and GL were regarded as thetransition between shallow donor levels such as oxygen vacancy and interstitial zinc. Based on the transitionlevel and formation energy of the ZnO intrinsic defects predicted through the first principle calculation, whichemploys density functional approximation (DFA) revised by local density approximation (LDA) and the LDA+Uapproach, the green and blue luminescence are nearly coincident with the transition from the conduction bandto zinc vacancies of V2-Zn and V-Zn, respectively.

본 논문에서는 청색 인광 발광 물질인 bis(3,5-Difluoro-2-(2-pyridyl)phenyl-(2-carboxypyridyl) iridium (III) (Flrpic)과 녹색 인광 발광 물질인 fac-tris(2-phenypyridine) irdium(III) (Ir(ppy)3)와 적색 인광 발광 물질인 his(5-benzoyl-2-phenylpyridinato-C,N)iridium(III) (acetylacetonate) ((Bzppy)2Ir(acac))를 각각 적층하여 백색 유기 발광 다이오드를 제작하였고, 각각의 발광층 사이에 혼합된 스페이서인 4,4'-N,N'-dicarbazole-biphenyl (CBP):4,7-diphenyl-1,10-phenanthroline (BPhen)을 적층하여 그 때의 영향에 대하여 연구하였다. 최적화된 구조에서의 전력 효율은 0.014 mA/cm2에서의 19.7 lm/w를 나타내었으며, 0.127 mA/cm2에서의 11.5%의 외부 양자 효율을 나타내었고, 8 V에서 Commission Internationale do I'Eclairage (CIEx,y) coordinates (x=0.36, y=0.44)의 색좌표를 나타내었다.

For possible applications as luminescent materials for white-light emission using UV-LEDs, Ba2Mg(PO4)2:Eu2+ phosphors were prepared by a solid state reaction. The photoluminescence properties of the phosphor were investigated under ultraviolet ray (UV) excitation. The prepared phosphor powders were characterized to from a single phase of a monoclinic crystalline structure by a powder X-ray diffraction analysis. In the photoluminescence spectra, the Ba2Mg(PO4)2:Eu2+ phosphor showed an intense emission band centered at the 584 nm wavelength due to the f-d transition of the Eu2+ activator. The optimum concentration of Eu2+ activator in the Ba2Mg(PO4)2 host, indicating the maximum emission intensity under the excitation of a 395 nm wavelength, was 5 at%. In addition, it was confirmed that the Eu2+ ions are substituted at both Ba2+ sites in the Ba2Mg(PO4)2 crystal. On the other hand, the critical distance of energy transfer between Eu2+ ions in the Ba2Mg(PO4)2 host was evaluated to be approximately 19.3 A. With increasing temperature, the emission intensity of the Ba2Mg(PO4)2:Eu phosphor was considerably decreased and the central wavelength of the emission peak was shifted toward a short wavelength.

Squid jigging fishery is very important in that there are about 1,000 jigging vessels more than 10 tonnage and about 5,000 ones less than 10 tonnage in Korea. But the cost of oil which is used to light fishing lamps, goes significantly up to almost one hundred million won for 50 tonnage vessels and forty million won in case of vessels less than 10 tonnage. This cost has almost taken 40% of total fishing costs. That is, the fishing business condition of squid jigging fishery is recently in the very difficult situation. As oil price increases, the business condition of the fishery gets worse and worse. Therefore it is very urgent to develop an economical fishing lamp, to solve this problem of fishery's business difficulty. This research aims at developing a fishing lamp for squid jigging fishery using the light emitting diode which has very excellent efficiency and durability. We made a water tank with 20 meters width which is a shape of raceway to research behavioral characteristics of Japanese flying squid to LED light, and made an experiment to investigate optimum wave of LED light to lure squid. The method is to establish LED lamps on both ends of water tank and to observe squid's behavior. Colors and wave lengths of LED lamps, used in experiment, are red(634nm), yellow(596nm), green(523nm), blue(454nm) and white(454nm+560nm). In experiment for attractive capability of LED lamp to squids, Japanese flying squid are highly attracted to blue lamp and white lamp. However, they are dispersed to red and yellow lamps. In addition, Japanese flying squid have moved and stayed in both dark ends of water tank. When compared intermittent lamp with continuous lamp, Japanese flying squid are highly attracted to intermittent lamp when intermittent interval is 0.25 second.

We have synthesized Eu3+-doped YVO4 phosphors by using a hydrothermal method and investigatedtheir luminescent properties. Aqueous solutions of Y2O3, V2O5, Eu2O3, and nitric acid with various pH valueswere used as the precursors. The crystallinity, surface condition, and emission characteristics were examinedusing XRD, FT-IR, and photo-excited spectrometer. Eu3+ incorporation followed by the efficient red emissionstrongly depends on the acidity of solution media. The emission intensity becomes stronger as the pH valuesincrease to 7 and then gradually decreases. This phenomenon might be related to the hydroxyl quenchingeffect, which is induced by surface bound OH- groups.

We report on the light-emitting diode (LED) characteristics of core-shell CdSe/ZnS nanocrystal quantum dots (QDs) embedded in TiO2thin films on a Si substrate. A simple p-n junction could be formed when nanocrystal QDs on a p-type Si substrate were embedded in ~5 nm thick TiO2 thin film, which is inherently an n-type semiconductor. The TiO2 thin film was deposited over QDs at 200˚C using plasma-enhanced metallorganic chemical vapor deposition. The LED structure of TiO2/QDs/Si showed typical p-n diode currentvoltage and electroluminescence characteristics. The colloidal core-shell CdSe/ZnS QDs were synthesized via pyrolysis in the range of 220-280˚C. Pyrolysis conditions were optimized through systematic studies as functions of synthesis temperature, reaction time, and surfactant amount.

We have fabricated and evaluated newNew high high-efficiency green green-light light-emitting phosphorescent devices with an emission layer of [TCTA/TCTA1/3TAZ2/3/TAZ] : Ir(ppy)3 were fabricated and evaluated, and compared the electroluminescence characteristics of these devices were compared with the conventional phosphorescent devices with emission layers of (TCTA1/3TAZ2/3) : Ir(ppy)3 and (TCTA/TAZ) : Ir(ppy)3. The current density, luminance, and current efficiency of the a device with an emission layer of (80Å-TCTA/90˚Å-TCTA1/3TAZ2/3/130Å-TAZ) : 10%-Ir(ppy)3 were 95 mA/cm2, 25000 cd/m2, and 27 cd/A at an applied voltage of 10 V, respectively. The maximum current efficiency was 52 cd/A under the a luminance value of 400 cd/m2. The peak wavelength and FWHM (FWHM (full width at half maximum) in the electroluminescence spectral were 513 nm and 65 nm, respectively. The color coordinate was (0.30, 0.62) on the CIE (Commission Internationale de I'Eclairage) chart. Under the a luminance of 15000 cd/m2, the current efficiency of the a device with an emission layer of (80Å-TCTA/90Å-TCTA1/3TAZ2/3/130Å-TAZ) : 10%-Ir(ppy)3 was 34 cd/A, which has beenshowed an improvement of improved 1.7 and 1.4 times compared to those of the devices with emission layers of (300Å-TCTA1/3TAZ2/3) : 10%-Ir(ppy)3 and (100Å-TCTA/200Å-TAZ) : 10%-Ir(ppy)3, respectively.

Among the efforts to increase the efficiency of organic light-emitting device (OLED), there is a way: doping phosphorescent materials. As a phosphorescent material, complexes of heavy transition metal, platinum, were synthesized. Cl- ion and phenyl group were used as ancillary ligands with 2-(2-pyridyl)benzimidazole (pbi) as a chromophore. The complexes were analysed by FAB-mass spectrometer and absorption and emission spectra were obtained. A phenyl group was able to shift the emission band of the complex even if it's not a chromorphore.

High-efficiency phosphorescent organic light emitting diodes using TCTA-TAZ as a double host and Ir(ppy)3 as a dopant were fabricated and their electro-luminescence properties were evaluated. The fabricated devices have the multi-layered organic structure of 2-TNATA/NPB/(TCTA-TAZ) : Ir(ppy)3/BCP/SFC137 between an anode of ITO and a cathode of LiF/AL. In the device structure, 2-TNATA[4,4',4"-tris(2-naphthylphenyl-phenylamino)-triphenylamine] and NPB[N,N'-bis(1-naphthyl)-N,N'-diphenyl-1,1'-biphenyl-4,4'-diamine] were used as a hole injection layer and a hole transport layer, respectively. BCP [2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline] was introduced as a hole blocking layer and an electron transport layer, respectively. TCTA [4,4',4"-tris(N-carbazolyl)-triphenylamine] and TAZ [3-phenyl-4-(1-naphthyl)-5-phenyl-1,2,4-triazole] were sequentially deposited, forming a double host doped with Ir(ppy)3 in the [TCTA-TAZ] : Ir(ppy)3 region. Among devices with different thickness combinations of TCTA (50 Å-200 Å) and TAZ (100 Å-250 Å) within the confines of the total host thickness of 300 Å and an Ir(ppy)3-doping concentration of 7%, the best electroluminescence characteristics were obtained in a device with 100 Å-think TCTA and 200 Å-thick TAZ. The Ir(ppy)3 concentration in the doping range of 4%-10% in devices with an emissive layer of [TCTA (100 Å)-TAZ (200 Å)] : Ir(ppy)3 gave rise to little difference in the luminance and current efficiency.

Blue-emitting BAM:Eu phosphor powders were formed by post-treatment of precursor powders with hollow or dense morphologies. The morphologies of the precursor powders obtained by spray pyrolysis were controlled by changing the preparation conditions and by changing the type of spray solution. The effects of the morphologies of the precursor powders on the characteristics of the BAM : Eu phosphor powders reacted with AlF3 flux were investigated. Precursor powders with a spherical shape and a hollow morphology produced BAM : Eu phosphor powders with a plate-like morphology, a fine size and a narrow size distribution. On the other hand, precursor powders with a spherical shape and dense morphology produced BAM : Eu phosphor powders with a plate-like morphology and a large size. AlF3 flux improved the photoluminescence intensities of the BAM : Eu phosphor powders. The photoluminescence intensity of the fine-sized BAM : Eu phosphor powders with a plate-like morphology was 90% of the commercial product under vacuum ultraviolet conditions.