The wheel is an active area of automobile component design and development. The wheel must be durable enough to tolerate significant loads and harsh environment. Temporary tire substituted for spare tire is made in a half band wheel size. Therefore this temporary tire is carried out lightweight and fuel saving of automobile. In this research, structural analysis and fatigue analysis of the temporary steel wheel are carried out using ANSYS 3D-modeling. The model is verified by the equivalent(von-Mises) stress analysis obtained from the ANSYS static structural analysis. Fatigue analysis is performed at the equivalent stress considering the automobile load and moment. Finally, this temporary wheel can be used temporary but not continuously.

This study presents a structural safety analysis method for a plant annunciator panel under the seismic effect. Seismic qualification analysis for the nuclear plant annunciator panel is carried out to confirm the structural integrity and the results are represented by required response spectra. For the numerical analysis, finite element method is adopted. Mode combinations are also used to obtain the reliability of the spectrum analysis. The analysis results shows that the nuclear plant annunciator panel is designed as a dynamically rigid assembly, without any resonance frequency blow 33Hz. The calculated stress of the nuclear plant annunciator panel is much less than yield stress of used steel.

Pile foundations constructed by the fiber reinforced polymer plastic piles have been used in coastal and oceanic regions in many countries. Generally, fiber reinforced polymer plastic piles are consisted of filament winding FRP which is used to wrap the outside of concrete pile to increase the axial load carrying capacity or pultruded FRP which is located in the core concrete to resist the bending moment arising due to eccentric loading. In this paper, the analytical procedures of hybrid concrete filled FRP tube flexural members are suggested based on the CFT design method. Moreover, the analytical results are compared with the experimental results to obtained by the previous researches. The results of comparison analyses are performed to estimate the accuracy of the analytical procedure for hybrid FRP-concrete composite compression test, members under eccentrical loading.

Air Brake chamber is a core fucntional part delivering the brake force to drum brakes in hybrid commercial trucks. This part needs to have leakage prevention and durability for reliable operation. As an actuator by air pressure, there has to be no air leakeage, and because it is operated with high tention power spring, there has high durable spring head, that contacted power spring directly. In this study, a spring head was designed new size on weak points structually and simulated by structual simulation program. And, a flange and body tighten by clamp ring was simlated structual deformation by assembly torque and inner pressure. As a result, new desgned spring head has structual stablilty over 1.7～14.7% and deformation is in proprotion to inner pressure but the assembly torque of clamp ring is not related to deformation.

본고는 경기지역의 청동기시대 취락을 대상으로 기본적인 자료를 정리하여, 유적의 시기별 편년을검토하고, 이에 맞는 주거지의 배치를 통하여 취락의 구조를 연구하는데 목적이 있다. 중부지방의 청동기시대 취락의 시기적 구분은 조기, 전기, 중기, 후기로 구분한 안과, 전기(전·중·후), 중기(전·중·후), 후기로 나눈안으로 크게 대별될 수 있다. 두 구분 모두 토기문양과 유물의 조합을 기준으로 나누는데 있어서 큰 차이점은 없지만, 후기를 점토대토기단계로 인정하는 것은 공통점이며, 돌대문토기 단계를 조기로 인정할 것인의 여부, 구순각목공렬토기의 중기여부의 차이라 할 수 있겠다. 본고는 토기문양의 계기적 변천과정이 잘 나타나는 후자의 안을 기준으로 시기적 특징을 살펴보았으며, 시기별 주거지 배치관계도 살펴보았다. 전기취락의 구조는 정상부의 능선을 중심으로 구축하였고, 계획배치 형태보다는 주거지간의 공간확보차원에서 조성되었고, 중기에는 구릉사면에 집중화되는 현상이 나타나며, 후기에 들어서서는 외곽으로 배치되고 있는 특징이 확인된다. 이는 중기중반이후에 인구가 줄어드는 양상과도 부합되는 현상으로 풀이된다. 한편, 중기에 분묘가 확인되기 시작하는데, 집단묘보다는 소규모로 조성되는 현상이 간취되는데, 이는 분묘공간의 확대로 정의될 수 있으며, 농경과도 연관된다. 대형 및 중형취락의 기준에 대해 살펴본 결과, 김포 양촌, 소사동, 토진리·양교리 주변 일대 유적을 대형취락으로 판단하였다. 특히, 소사동유적은 전기~중기에 걸쳐 시기별로 고른 분포를 보이면서,마을이 운영된 점이 돋보이며, 양촌리, 토진리·양교리 주변 일대 4개유적은 중기에 집중된 유적으로,유적 상호간의 거리가 근접거리에 위치하고 있어, 한단위의 취락으로 판단하였다. 경기지역 청동기시대 취락의 시기적 변천은(물론 지역적 변천은 인정하며), 중기전반에 가장 취락의 규모가 융성한 것으로 나타났다. 물론 전기에 있어서 평택 소사동유적과 같은 규모가 큰 유적도 존재하지만, 대체적으로 중기전반에 규모가 최정점을 이루다가 중반이후로 규모가 쇠퇴하기 시작하는양상으로 나타나고 있다.

This study aims to evaluate structural safety through FEM on the hollow shaft and the shaft filled with aluminum foam as the impact beam made of high tensile strength steel, Force reactions of impact beams are investigated when the forced displacement of 50mm is applied equally on two beams. When impact velocity of 80km/h is applied onto impact beams equally with the limit velocity of automobile on national road, how much impact energies can be absorbed by beams are also investigated. As study result, impact beams without aluminum foam and with aluminum foam show the maximum reaction forces of 15.53kN and 20.34kN respectively in case of the forced displacement of 50mm. As impact analysis result, impact beams without aluminum foam and with aluminum foam can absorb impact energies of 560J and 820J respectively. As impact beam with aluminum foam has reaction force and impact energy more than 23% and 30% than without aluminum foam, impact beam with aluminum foam has more safety than without aluminum foam.

As fires have frequently occurred with large scale at cultural assets and warehouses, the development of Korean type demolition fire apparatus for efficient fire fighting becomes important. In this study, structural stability is investigated for assembly model of boom and outrigger by using computational structural analysis. Analysis results of boom and outrigger unit are also compared with assembly model. As this study result, equivalent stress result of boom unit is about 6% higher than assembly model and equivalent stress result of outrigger unit is about 15% higher than assembly model.

In this study, BaTiO3 thin films were grown by RF-magnetron sputtering, and the effects of the thin film thickness on the structural characteristics of BaTiO3 thin films were systematically investigated. Instead of the oxide substrates generally used for the growth of BaTiO3 thin films, p-Si substrates which are widely used in the current semiconductor processing, were used in this study in order to pursue high efficiency in device integration processing. For the crystallization of the grown thin films, annealing was carried out in air, and the annealing temperature was varied from 700˚C. The changed thickness was within 200 nm~1200 nm. The XRD results showed that the best crystal quality was obtained for ample thicknesses 700 nm~1200 nm. The SEM analysis revealed that Si/BaTiO3 are good quality interface characteristics within 300 nm when observed thickness. And surface roughness observed of BaTiO3 thin films from AFM measurement are good quality surface characteristics within 300 nm. Depth-profiling analysis through GDS (glow discharge spectrometer) showed that the stoichiometric composition could be maintained. The results obtained in this study clearly revealed BaTiO3 thin films grown on a p-Si substrate such as thin film thickness. The optimum thickness was 300 nm, the thin film was found to have the characteristics of thin film with good electrical properties.

회전하는 수조에서 나타나는 순압성 소용돌이의 패턴과 구조 회전에 대한 연구를 수행하였다. 소용돌이는 수면 위에 접촉된 원판을 수조에 대해 상대적으로 회전시키는 방법을 통해 만들어졌다. 회전원판의 크기, 회전방향, 회전속력에 따라 트라이폴라 소용돌이, 삼각형 소용돌이, 사각형 소용돌이, 커다란 원형 소용돌이가 안정하게 나타났고, 모양이 계속 변하는 불안정한 소용돌이도 나타났다. 회전원판과 수조 벽 사이의 간격이 안정한 소용돌이의 패턴에 큰 영향을 주었고 불안정한 소용돌이는 원판이 시계방향으로 빠르게 회전할 때 주로 나타났는데, 그 원인은 원심력적 불안정성이었다. 한편, 트라이폴라 소용돌이에서 나타난 전체 패턴의 구조적 회전 각속도는 원판 가장자리의 선속도에 비례하였고, 고기압성 트라이폴라 소용돌이가 저기압성 보다 더 큰 구조 회전 각속도를 가졌다. 로스비 수와 구조회전의 관점에서 볼 때, 해양에서 발견된 트라이폴라 소용돌이와 본 실험에서 나타난 트라이폴라 소용돌이는 유사하였다.

ZnO thin films co-doped with Mg and Ga (MxGyZzO, x+y+z=1, x=0.05, y=0.02 and z=0.93) were preparedon glass substrates by RF magnetron sputtering with different sputtering powers ranging from 100W to 200W at a substratetemperature of 350oC. The effects of the sputtering power on the structural, morphological, electrical, and optical propertiesof MGZO thin films were investigated. The X-ray diffraction patterns showed that all the MGZO thin films were grown asa hexagonal wurtzite phase with the preferred orientation on the c-axis without secondary phases such as MgO, Ga2O3, orZnGa2O4. The intensity of the diffraction peak from the (0002) plane of the MGZO thin films was enhanced as the sputteringpower increased. The (0002) peak positions of the MGZO thin films was shifted toward, a high diffraction angle as thesputtering power increased. Cross-sectional field emission scanning electron microscopy images of the MGZO thin filmsshowed that all of these films had a columnar structure and their thickness increased with an increase in the sputtering power.MGZO thin film deposited at the sputtering power of 200W showed the best electrical characteristics in terms of the carrierconcentration (4.71×1020cm−3), charge carrier mobility (10.2cm2V−1s−1) and a minimum resistivity (1.3×10−3Ωcm). A UV-visible spectroscopy assessment showed that the MGZO thin films had high transmittance of more than 80% in the visibleregion and that the absorption edges of MGZO thin films were very sharp and shifted toward the higher wavelength side, from270nm to 340nm, with an increase in the sputtering power. The band-gap energy of MGZO thin films was widened from3.74eV to 3.92eV with the change in the sputtering power.

In this study, the stability of baby carriage is investigated through fatigue and vibration analyses according to the seat configuration.

Nickel oxide was doped with a wide range of concentrations (mol%) of Aluminum (Al) by solvothermal synthesis;single-phased nano powder of nickel oxide was generated after calcination at 900oC. When the concentration of Al dopant wasincreased, the reduced intensity was confirmed through XRD analysis. Lattice parameters of the synthesized NiO powder weredecreased after treatment of the dopant; parameters were increased when the concentration of Al was over the doping limit(5mol% Al). The binding energy of Ni2+ was chemically shifted to Ni3+ by doping Al3+ ion, as confirmed by the XPS analysis.The tilted structure of the synthesized NiO with 5mol% Al dopant and the polycrystalline structure of the Ni0.75Al0.25O wereobserved by HR-TEM analysis. The electrical conductivity of the newly synthesized NiO was highly improved by Al dopingin the conductivity test. The electrical conductivity values of the commercial NiO and the synthesized NiO with 5mol% Aldopant (Ni0.95Al0.05O) were 1,400s/cm and 2,230s/cm at 750oC, respectively. However, the electrical conductivity of thesynthesized NiO with 10mol% Al dopant (Ni0.9Al0.1O) decreased due to the scattering of free-electrons caused by the largenumber of impurity atoms; the electrical conductivity of Ni0.9Al0.1O was 545s/cm at 750oC.

The purpose of this study is to investigate the crystalline structure and optical properties of (GaZn)(NO) powders prepared by solid-state reaction between GaOOH and ZnO mixture under NH3 gas flow. While ammoniation of the GaOOH and ZnO mixture successfully produces the single phase of (GaZn)(NO) solid solution within a GaOOH rich composition of under 50 mol% of ZnO content, this process also produces a powder with coexisting (GaZn)(NO) and ZnO in a ZnO rich composition over 50 mol%. The GaOOH in the starting material was phase-transformed to α-, β-Ga2O3 in the NH3 environment; it was then reacted with ZnO to produce ZnGa2O4. Finally, the exchange reaction between nitrogen and oxygen atoms at the ZnGa2O4 powder surface forms a (GaZn)(NO) solid solution. Photoluminescence spectra from the (GaZn)(NO) solid solution consisted of oxygen-related red-emission bands and yellow-, green- and blue-emission bands from the Zn acceptor energy levels in the energy bandgap of the (GaZn)(NO) solid solutions.

The purpose of this study was to analyze the effects of quality factors on value, satisfaction and loyalty in a wine training program. The results of this study can be summarized as follows: Structural verification of the wine training program loyalty model showed that the quality of the wine training program positively affected both value (p<0.001) and satisfaction (p<0.001). Further, the value of the wine training program positively affected satisfaction (p<0.01), which in turn positively influenced loyalty (p<0.001). The quality of the wine training program was presented as solicitude for students, textbook and curriculum, qualification and confidence of lecturer and staff, and training quality, whereas the value of the program was composed of sense of belonging, promotion of self-esteem, good impression on others, and improvement of social status. Therefore, the wine training institute's intensive management of the quality and value of the program could induce students' loyalty by enhancing satisfaction for the wine training program.

그동안 출연연은 과학기술 발전을 선도하는 핵심 역할을 담당해 왔으나 최근에는 조직의 경쟁력 문제를 포함하여 그 미션과 역할까지 새롭게 정립해야 하는 시점에 있다. 본 연구는 ETRI를 결정적인 사례로 하여 현재 출연연이 직면하고 있는 구조적 한계와 어려움을 살펴보았다. 분석 결과 출연연의 자체 변화 노력도 문제이지만 출연연이 예산, 인력, 평가 등 통제가 어려운 구조적인 문제에 봉착되어 있음을 알 수 있다. ETRI의 경우 연구개발이나 특정기술 수준에서는 추격에서 탈추격으로 넘어서고 있으나 우리나라 출연(연) 연구 환경과 실제 일하는 방식은 추격형 체제에 머물러 있는 상황이다. 추격의 대상과 수단이 어느 정도 확실했던 추격기를 넘어 어디로 가야하며 무엇을 해야 할 것인가가 불확실한 탈추격 혁신 상황에서는 출연연의 미션 및 역할, 예산·인력·평가 체계, 사업기획 체계 및 프로세스 방식 등이 새롭게 변화될 필요가 있다.

This study is intended to Mindori structure which is general private houses' structural type among traditional types and is a basic study to confirm structural characteristics of Hwatong connection which is general connection type of column-beam-cross beam. It is aimed to analyze how main member ,column, such as size, figure, thickness of Sungetuk and Dugeup affect on structure. Following conclusions are drawn. 1. According to connection conditions, models with big coefficient of friction show stable hysteretic behavior until the angle rotation of member reaches 1/60 and models with small coefficient of friction show dramatical increase in load after the angle rotation of member reaches 1/24. After the angle rotation of member reaches 1/30, separation distance of members is identified physically and cracks are not observed. 2. Specimens with big coefficient of friction show similar inner force regardless of column size(except column size 150mm) and models with small coefficient of friction show increasing inner force as the column size increases. Specimens with same sectional area have similar inner force even though the column figures are different. The thickness of Sungetuk and Dugeup doesn't affect inner force greatly, however, when the thickness of Sungetuk is thin, it could lead to failure of structure as it breaks. 3. The bigger the size of column and the coefficient of friction are, the smaller Bending stiffness depreciation ratio is. 4. Energy Dissipation Efficiency differs from the coefficient of friction. When the coefficient of friction is big, square column shows bigger than round one and it is bigger when the thickness of Sungetuk and Dugeup is thicker. When the coefficient of friction is small, round column shows bigger than square one.