간행물
한국분말야금학회 학술대회논문집
- 발행기관 한국분말재료학회(구 한국분말야금학회)
- 자료유형 학술대회
- 간기 부정기
- 수록기간 1993 ~ 2006
- 주제분류 공학 > 금속공학 공학 분류의 다른 간행물
- 십진분류KDC 559DDC 629
권호리스트/논문검색
한국분말야금학회 2006년도 춘계학술대회논문집 (2006년 4월) 443건
41.
2006.04
구독 인증기관·개인회원 무료
42.
2006.04
구독 인증기관·개인회원 무료
The relationship between the powder particle size change and a mechanical property of the Metal Injection Molding (MIM) product was examined in detail. The XRD results indicate that the diffraction peaks of BCC appeared in compacts of powder particle size of 4 to as well as the bulk SUS630. However, the diffraction peaks from both BCC and FCC were observed in the compact with powder size less than . TEM observation revealed that the powder with those BCC/FCC two phase structure have a finely dispersed precipitates. Because the Si is ferrite stabilizing element, decrease of Si composition in the matrix phase by the precipitation resulted in formation of the retained austenite. Therefore, controlling the elements such as Si as well as oxygen decrease is very important to obtain a normal microstructure in ultra-fine powder (<3μm) injection molding.
43.
2006.04
구독 인증기관·개인회원 무료
Dang-Thuy Nguyen, Dae-HWan Kwon, Dina Dudina, Pyuck-pa choi, Jong-won Kum, Jin-Chun Kim, ji-Soon Kim, Young-Soon Kwon
44.
2006.04
구독 인증기관·개인회원 무료
Small powder size is very useful in achieving detailed structures. STS 316 nanopowders with an average diameter of 100 nm and were utilized to produce feedstock. The mixing behavior of the feedstock indicated that the nanoparticle feedstock produced the highest mixing torque at various powder loading compared to the micropowder feedstock. The nanoparticles feedstocks showed that elastic properties are dominant in flow behavior and high viscosity. Conversely the micropowders feedstocks, viscous properties are dominant in flow behavior and less viscosity, nanopowders feedstock perform lower flow activation energy than feedstock with bigger particles.
45.
2006.04
구독 인증기관·개인회원 무료
46.
2006.04
구독 인증기관·개인회원 무료
The production method of micro sacrificial plastic mold insert metal injection molding, namely process has been proposed to solve specific problems involving the miniaturization of MIM. Two types of sacrificial plastic molds (SP-mold) with fine structures were used: 1) PMMA resist, 2) PMMA mold injected into Ni-electroform, which is a typical LIGA () process. Stainless steel 316L feedstock was injection-molded into the SP-molds with multi-pillar structures. This study focused on the effects of metal particle size and processing conditions on the shrinkage, transcription and surface roughness of sintered parts.
47.
2006.04
구독 인증기관·개인회원 무료
48.
2006.04
구독 인증기관·개인회원 무료
In recent years, micro powder injection molding is being explored as an economical fabrication method for microcomponents in microsystems technology (MST). Technical and economic comparison was performed for processes. Molding experiment and simulation during the filling process were performed to evaluate several different geometries and processing conditions. The influence of material parameters and process conditions on mold filling were examined as a function of features size using microchannels as an example. It was found that the heat conductivity and viscosity of feedstock, geometry and mold temperature were the most critical parameters for complete filling of micro features.
49.
2006.04
구독 인증기관·개인회원 무료
50.
2006.04
구독 인증기관·개인회원 무료
고주파유도가열 연소합성법으로 60MPa의 기계적 압력과 고주파유도가열 장치의 총용량 (15KW)의 90%의 출력을 가해 75초의 짧은 시간에 97%이상의 상대밀도를 갖는 복합체를 제조하였으며, 제조된 시편의 미세조직 사진으로부터 선형분석법으로 측정한 의 평균 결정립크기는 각각 250nm 과 60nm 이었다. 또한 제조된 시편을 연마하여 비커스 경도계를 이용하여 기계적 특성평가를 한 결과 경도 와 파괴인성은 각각 와 이었다.
51.
2006.04
구독 인증기관·개인회원 무료
Oridinal thermal spray process has developed into two ways, namely, temperature dominated represented by plasma spraying, and velocity dominated represented by HVOF. It is common for both that the particle materials sprayed are basically in melted or half melted condition. New process has developed recently, that is, Cold Spray and Aerosol Deposition. Particle's heating is limited in CS lower than half of the material's melting point. Moreover, exactly no heating is loaded in AD process. Through the investigation on common feature for these three spraying processes, potential of new material process - Particle Deposition, PD - is considered and proposed
52.
2006.04
구독 인증기관·개인회원 무료
53.
2006.04
구독 인증기관·개인회원 무료
54.
2006.04
구독 인증기관·개인회원 무료
[ ] composite powders were produced by high energy mechanical milling of a mixture of Al and powders followed by a combustion reaction. The powders were subsequently thermally sprayed on H13 steel substrates. Microstructural examination was conducted on the composite powders and thermally sprayed coatings, using X-ray diffractometry (XRD) and scanning electron microscopy (SEM). The performance of the coatings was evaluated in terms of micro-hardness and thermal fatigue. The thermally sprayed coatings performed very well in the preliminary thermal fatigue tests and showed no wetting tendency to molten aluminum.
55.
2006.04
구독 인증기관·개인회원 무료
56.
2006.04
구독 인증기관·개인회원 무료
[ ] powders were thermally sprayed onto mild steel substrates in air and under a reduced pressure of argon. Several oxides were formed after thermally-spraying the mechanically-alloyed powders in air. After spraying in a reduced pressure of argon, the coating layers obtained from the gently mixed powders consisted of the elemental metals, but an amorphous phase primarily appeared in the thermally-sprayed mechanically-alloyed powders, which transformed into the icosahedral quasicrystal phase and a minor crystal phase after annealing at 828 K. The Vickers hardness and the contact angle with pure water for the quasicrystal layers were about 7 GPa and respectively.
57.
2006.04
구독 인증기관·개인회원 무료
58.
2006.04
구독 인증기관·개인회원 무료
59.
2006.04
구독 인증기관·개인회원 무료
60.
2006.04
구독 인증기관·개인회원 무료
Ti-Zr-Ni coatings deposited by low vacuum plasma spray technique consisted of nanometer-sized 1/1 cubic approximant and TiZrNi Laves phases as well as a low volume fraction of phase. The shift of composition during deposition of the quasicrystalline powders and the presence of phases are believed to be responsible for the reduced corrosion performances evaluated by means of electrochemical tests in a Hanks' Balance Salt Solution at .
