In this study, three kinds of bainitic steels are fabricated by controlling the contents of vanadium and boron. High vanadium steel has a lot of carbides and nitrides, and so, during the cooling process, acicular ferrite is well formed. Carbides and nitrides develop fine grains by inhibiting grain growth. As a result, the low temperature Charpy absorbed energy of high vanadium steel is higher than that of low vanadium steel. In boron added steel, boron segregates at the prior austenite grain boundary, so that acicular ferrite formation occurs well during the cooling process. However, the granular bainite packet size of the boron added steel is larger than that of high vanadium steel because boron cannot effectively suppress grain growth. Therefore, the low temperature Charpy absorbed energy of the boron added steel is lower than that of the low vanadium steel. HAZ (heat affected zone) microstructure formation affects not only vanadium and boron but also the prior austenite grain size. In the HAZ specimen having large prior austenite grain size, acicular ferrite is formed inside the austenite, and granular bainite, bainitic ferrite, and martensite are also formed in a complex, resulting in a mixed acicular ferrite region with a high volume fraction. On the other hand, in the HAZ specimen having small prior austenite grain size, the volume fraction of the mixed acicular ferrite region is low because granular bainite and bainitic ferrite are coarse due to the large number of prior austenite grain boundaries.

시설 토양 오이재배에서 토양수분장력계를 이용하여 관수 제어하였을 때 오이의 광합성 형광반응, 수액 흐름, 엽온 등에 미치는 영향을 구명하고자 실험을 수행하였다. 오이(Cucumis sativus L.)‘청춘’(해오름 종묘)을 공시하여 관수개시점 10-10-20kPa 또는 20-10-10kPa의 2처리하였다. 766 ~ 854 W·m -2 의 고광, 32°C 이상의 고온인 처리 66일 째 광합성형광반응변수(Fo, Fm, Fv/Fm)값은 처리 간 차이가 컸다. 66일 째 낮 시간 (오전 10시 반 ~ 오후 6시)의 Fo와 Fv/Fm값은 10-10-20kPa 처리보다 20-10-10kPa 처리에서 높았다. 엽온이 높았을 때 Fv/Fm값은 감소하였다. 28일과 66일째 엽생육(엽장, 엽폭, 엽면적)은 차이가 없었으나 엽록소 함량(SPAD 값)은 20-10- 10kPa 처리에서 유의하게 높았다. 광도와 온도가 증가함에 따라 줄기수액흐름상대율(SFRR)과 엽온은 상승하였다. 두 처리구 모두 SFRR은 광도 170 W·m -2 이상인 오전 8시 ~ 9시 간대에 급격한 증가가 시작되었다. 관수 후의 처리구 토양 온도는 감소하였으나, 7월 5일(광도 820W·m -2 , 오후 1시) 토양 온도가 10-10-20kPa에서는 31.0°C, 20-10-10kPa에서는 28.5°C였다. 그러나 처리 간 SFRR, 엽온, 기온차, VPD는 차이가 없었다. SFRR과 엽온 간에는 정의 상관성(p < 0.01, r = 0.770)을 보였으며, SFRR과 엽온은 광, 온도, 토양 온도, 토양 수분함량, VPD 간에는 정의 상관을 상대습도와 기온차 간에는 부의 상관을 보였다.

This study analyzes the internal temperature characteristics of heater module using a numerical method when the constant heat flux and heat flux time are applied to the surface heating element. The horizontal and vertical dimensions of heater module are 100mm, and the height is 5mm. The heat flux is 10,000W/m2, 15,000W/m2, and 20,000W/m2, and heat flux time is 5 seconds, 10 seconds, 15 seconds, 20 seconds, 30 seconds and 50 seconds, respectively. When the heat flux time was 50 seconds, the temperature of the surface heating element rose to 120.5°C, while the skin epidermis temperature rose 1.7°C. As a result, the surface temperature of the surface heating element increased greatly in the horizontal direction, while it increased low in the depth direction. This is because the heat conduction of the surface heating element is transmitted in the X-Y plane direction, and the thermal conductivity of the pet(polyethylene terephthalate) film and insulation sheet under the surface heating element is very low. when the heat flux at the surface heating element is 20,000W/m2, the skin's epidermal temperature rises up to 0.82℃ compared to 10,000W/m2 and 15,000W/m2.

본 연구는 수출용 큰느타리버섯의 선도 유지 및 저장성 증대를 위한 배지 적합 질소함량과 생육온도 조건을 설정 하고자 하였다. 배지 질소함량 1.5%, 1.8%, 2.1%, 2.4% 및 생육온도 15 ̊C, 12 ̊C, 9 ̊C 조건별로 자실체의 생육특성, 수확 후 냉장저장기간 동안의 가스농도, 자실체 품질 변화를 조사하였다. 대직경과 중량은 생육온도와 관계없이 질소함량이 높아질수록 증가하는 경향을 보였으며 병 당 중량은 12 o C, T-N 2.4% 조건에서 149.5 g으로 가장 높았다. 갓 색은 배지 질소함량과 관계없이 온도가 낮아 질수록 색도(L)가 낮아져 갓 색이 진해졌다. 저장기간에 따른 봉지 내 가스농도 변화는 9 ̊C, T-N 2.1% 조건에서 산도 농도가 가장 오래 유지되었다. 달관조사에 의한 자실체 품질평가에서 배지 질소함량에 따른 차이는 나타나지 않았고 저장기간 28일까지 이취, 변색, 부패 정도는 15 ̊C와 9 ̊C가 유사하게 나타났다.

A zinc-air battery consists of a zinc anode, an air cathode, an electrolyte, and a separator. The active material of the positive electrode is oxygen contained in the ambient air. Therefore, zinc-air batteries have an open cell configuration. The external condition is one of the main factors for zinc-air batteries. One of the most important external conditions is temperature. To confirm the effect of temperature on the electrochemical properties of zinc-air batteries, we perform various analyses under different temperatures. Under 60 oC condition, the zinc-air cell shows an 84.98 % self-discharge rate. In addition, high corrosion rate and electrolyte evaporation rate are achieved at 60 oC. Among the cells stored at various temperature conditions, the cell stored at 50 oC delivers the highest discharge capacity; it also shows the highest self-discharge rate (65.33 %). On the other hand, the cell stored at 30 oC shows only 2.28 % self-discharge rate.

Mass mortality of mariculture fish due to high summer temperatures is a major issue in the mariculture industry in many coastal waters of Korea, yet measures to mitigate the impact are generally limited. We injected a micro-bubble of liquefied oxygen into the bottom of rockfish cages (about 6-8 m deep) in order to maximize the dispersal of micro-bubbled seawater and reduce fish mortality. The injection of low-temperature oxygen in micro-bubbles lowered the water temperature at the injection area by as much as 1℃ and increased dissolved oxygen concentration by 0.5 ppm. In early August, following a week with persistent high water temperature (above 28.5℃), there was an increase in fish mortality despite the micro-bubble system, which resulted in approximately 7% death of the total introduced fish population. However, this mortality appeared to be much lower than mortality reported in a neighboring mariculture facility (approximately 50% mortality). We also estimated the volume that can be recirculated with pumped seawater using a micro-bubble system. We suggest that this approach of injecting liquefied oxygen through a micro-bubble system may reduce fish mortality during high temperature periods.

This study aimed to investigate the effect of storage temperature and pressure plate treatment on chemical composition in Prunus mume sugar extracts (PSEs). Green Prunus mume fruit was mixed with an equal amount of commercial sugar and stored at 4 or 25oC for 9 mon with or without a pressure plate. The alcohol contents in PSEs stored at 4oC were lower than those stored at 25oC. The amygdalin contents in PSEs stored at 25oC with pressure plate were significantly low. The sucrose in PSEs was converted into glucose and fructose during storage. The glucose, fructose and total phenol contents in PSEs stored at 25oC were higher compared with those at 4oC. The total soluble solid and polyphenol contents in PSEs were increased at 25oC until 90 d and 4oC until 150 d and then the contents were constant. The total acidity in PSEs stored at 4oC were higher than those at 25oC. These results indicate that storage temperature plays an important role in controlling the alcohol, amygdalin and sucrose contents in Prunus mume sugar extracts (PSEs).

This paper focuses on the electrical properties and stability against DC accelerated aging stress of ZnO-V2O5-MnO2- Nb2O5-Bi2O3-Co3O4-Dy2O3 (ZVMNBCD) varistor ceramics sintered at 850 - 925 ℃. With the increase of sintering temperature, the average grain size increases from 4.4 to 11.8 mm, and the density of the sintered pellets decreases from 5.53 to 5.40 g/ cm3 due to the volatility of V2O5, which has a low melting point. The breakdown field abruptly decreases from 8016 to 1,715 V/cm with the increase of the sintering temperature. The maximum non-ohmic coefficient (59) is obtained when the sample is sintered at 875 ℃. The samples sintered at below 900 oC exhibit a relatively low leakage current, less than 60 mA/cm2. The apparent dielectric constant increases due to the increase of the average grain size with the increase of the sintering temperature. The change tendency of dissipation factor at 1 kHz according to the sintering temperature coincides with the tendency of the leakage current. In terms of stability, the samples sintered at 900 ℃ exhibit both high non-ohmic coefficient (45) and excellent stability, 0.8% in ΔEB/EB and -0.7% in Δα/α after application of DC accelerated aging stress (0.85 EB/85 oC/24 h).

The various sintered samples comprising of 72 wt%(Al2O3) : 28 wt%(SiO2) based ceramics were fabricated using a colloidal processing route. The phase analysis of the ceramics was performed using an X-ray diffractometer (XRD) at room temperature confirming the presence of Al2O5Si and Al5.33Si0.67O9.33. The surface morphology of the fracture surface of the different sintered samples having different sizes of grain distribution. The resistive and capacitive properties of the three different sintered samples at frequency sweep (1 kHz to 1 MHz). The contribution of grain and the non-Debye relaxation process is seen for various sintered samples in the Nyquist plot. The ferroelectric loop of the various sintered sample shows a slim shape giving rise to low remnant polarization. The excitation performance of the sample at a constant electric signal has been examined utilizing a designed electrical circuit. The above result suggests that the prepared lead-free ceramic can act as a base for designing of dielectric capacitors or resonators.

This study examined the optimal temperature and time conditions to maintain high quality Dongchimi during the fermentation and storage period. Dongchimi was fermented at low (5oC), medium (10 and 15oC), and high (20oC) temperatures until the acidity reached 0.2, 0.3, and 0.4%. respectively. From the consumer’s preference test enrolling five consumers, Dongchimi fermented at 15oC until an acidity of 0.3% (for approximately six days) was evaluated to be the optimal status because of its high score of overall acceptance, taste, and odor of consumers. To determine the optimal storage temperature of fermentation, Dongchimi was stored at three different temperatures (−1, 2, 5oC) for four weeks after fermenting at 15oC for six days. During the storage period, most of the physicochemical properties (pH, acidity, reducing sugar content, and organic acid) and microbiological properties changed significantly in the 2 and 5oC groups, resulting in a significant change in descriptive sensory analysis of Dongchimi. These results indicate that fermentation at 15oC and storage at −1oC for Dongchimi enables it to maintain the best quality for a long time.

본 연구는 온도 상승에 따른 복숭아 ‘미홍’의 수체생육 및 생리반응에 미치는 영향을 알아보고자 수행되었다. 전주시 평년 온도를 대조구로 하여 평년 대비 +3.4℃(21C 중반기), +5.7℃(21C 후반기) 상승시켜 자연광온실에서 4월 25일부터 7월 5일까지 처리하였다. 수체 생육은 신초 수와 길이가 온도 상승에 따라 증가하였고, 엽면적은 통계적 유의차는 없었다. 수확기는 대조구, +3.4℃ 처리구, +5.7℃ 처리구에서 각각 7월 1일, 6월 24일, 21일로 온도가 높을수록 빨라졌다. 과중은 평년보다 3.4℃ 상승하였을 때 증가하였지만 5.7℃까지 상승할 경우 오히려 평년보다 감소하여, 주당 수량은 +3.4℃ 처리구(2,898g), 대조구(2,746g), +5.7℃ 처리구(2,404g) 순으로 많았다. 이는 과실 생육기인 5월부터 6월 초까지의 평균 최대광합성률이 +3.4℃ 처리구에서 14.93 μmol∙CO2∙m-2∙s-1 으로 대조구 13.79 μmol∙CO2∙m-2∙s-1와 +5.7℃ 처리구의 13.20 μmol∙CO2∙m-2∙s-1에 비해 높았고, 기공의 밀도 또한 +3.4℃ 처리구에서 229 ea/mm2로 대조구 181 ea/mm2에 비 해 높았던 결과와도 관련이 있는 것으로 판단된다. 다음해 수량에 영향을 미치는 화아분화율은 +5.7℃ 처리구에서 59.8% 로 대조구 63.8%, +3.4℃ 처리구 65.8%보다 감소하였다. 이상의 결과를 종합해보면 3.4℃ 까지의 온도 상승은 복숭아 ‘미홍’의 수량과 과실 품질에 긍정적인 영향을 주는 반면 5.7℃ 이상의 온도 상승은 부정적인 영향을 주는 것으로 판단된다.

Compartment fire tests were performed using kerosene and Jet A-1 as fire sources to evaluate the relationship between flame temperature and opening size. The tests were performed for a fire caused by the release of kerosene owing to vehicle impact, and for a fire caused by the release of Jet-A-1 owing to airplane collision. The compartment fire tests were performed using a 1/3-scale model of a metal storage cask when the flame temperature was deemed to be the highest. We found the combustion time of Jet-A-1 to be shorter than that of kerosene, and consequently, the flame temperature of Jet-A-1 was measured to be higher than that of kerosene. When the opening was installed on the compartment roof, even though the area of the opening was small, the ventilation factor was large, resulting in a high flame temperature and long combustion. Therefore, the position of the opening is a crucial factor that affects the flame temperature. When the metal storage cask was stored in the compartment, the flame temperature decreased proportionally with the energy that the metal storage cask received from the flame.

This study was conducted to investigate cucumber plants response to greenhouse environments by solar shading in greenhouse in the summer. In order to estimate heat stress reduction of cucumber plants by solar shading in greenhouse, we measured and analyzed physiological conditions of cucumber plants, such as leaf temperature, leaf-air temperature, rubisco maximum carboxylation rate, maximum electron transport rate, thermal breakdown, light leaf respiration, etc. Shading levels were 90% mobile shading of full sunlight, 40% mobile shading of full sunlight and no shading(full sunlight). The 90% shading screen was operated when the external solar radiation is greater than 650 W·m-2. Air temperature, solar radiation, leaf temperature, leaf-air temperature and light leaf respiration in the 90% shading of full sunlight was lower than those of 40% shading and no shading. Rubisco maximum carboxylation rate, arrhenius function value and light leaf respiration of the 90% shading were significantly lower than those of 40% shading and no shading. The thermal breakdown, high temperature inhibition, of 90% shading was significantly higher than that of 40% shading and no shading. Therefore, these results suggest that 90% mobile shading made a less stressful growth environment for cucumber crops.

Bismuth vanadate (BiVO4) is considered a potentially attractive candidate for the visible-light-driven photodegradation of organic pollutants. In an effort to enhance their photocatalytic activities, BiVO4 nanofibers with controlled microstructures, grain sizes, and crystallinities are successfully prepared by electrospinning followed by a precisely controlled heat treatment. The structural features, morphologies, and photo-absorption performances of the asprepared samples are systematically investigated and can be readily controlled by varying the calcination temperature. From the physicochemical analysis results of the synthesized nanofiber, it is found that the nanofiber calcines at a lower temperature, shows a smaller crystallite size, and lower crystallinity. The photocatalytic degradation of rhodamine-B (RhB) reveals that the photocatalytic activity of the BiVO4 nanofibers can be improved by a thermal treatment at a relatively low temperature because of the optimization of the conflicting characteristics, crystallinity, crystallite size, and microstructure. The photocatalytic activity of the nanofiber calcined at 350oC for the degradation of RhB under visible-light irradiation exhibits a greater photocatalytic activity than the nanofibers synthesized at 400oC and 450oC.