The air dilution olfactory method to measure complex odors needs to store and carry odor samples from the field sampling until the analysis in laboratories. Until the analysis of sample in the laboratory, odor dilution factor (odor sensitivity) in the sample bag may decrease over time depending on the characteristics of each odor substances. This is one of the limitation for the air dilution olfactory method. Thus, the air dilution device enable to measure without loss in complex odors of samples. Recently, many studies on the performance test of on-site air dilution devices, i.e., field olfactometer, has been conducted to figure out the feasibility of the field olfactometers. In this study, seven odor samples were collected from five odor emission source sites. And comparative analysis with the air dilution olfactory method was carried out to assess the field applicability of the olfactometer. As results, the performance of the field olfactometer used in this study is regared as the affordable method. The dilution factors from between two methods showed the similar values, indicating low values of standard deviations. In order to ensure the accuracy and precision of measurement data using the field olfactometer, methodology minimized variables (that may affect measurement) needs to establish.

In Korea, odor emission control is carried out at the boundary between the discharge port and the site based on the height of the discharge port, but in Japan and the U.K. a range of characteristics are considered in odor management, including the height, size, and amount of exhaust gas, when managing the acceptance criteria of the discharge port that conforms to the odor concentration standards based on the site boundary. In this study, the permitted concentration of odor in the outlet was studied considering the design conditions of the outlet, in order to manage it based on the distance between the outlet and the residential area. To improve the effectiveness of odor management, Korean odor management measures were reviewed by applying the methods used to calculate odor concentration in Japan and the U.K. Guidelines on effective odor reduction were provided by calculating the permissible odor concentration for each condition based on the flow rate and height of the final outlet to comply with the permissible concentration at regular intervals at the outlet of the factory.

본 연구는 계란 생산성, 계란품질 및 악취저감에 관한 Bacillus subtillus, Streptomyces galilaeus 및 Sphingobacteriaceae로 구성된 복합생균제(PM, probiotic mixture)의 효과를 조사하였다. 산란계 Hy-Line Brown 240수를 4처리구로 구분하여 6주 동안 사육하였다. 처리구는 복합생균제를 함유하지 않은 대조구(CON, control), 일반생균제(CP3, commercial probiotics 0.3%), 복합생균제 3(PM3, 복합생균제 0.3%), 복합생균제 5(PM5, 복합생균제 0.5%)로 구분하였다. 산란율, 계란 호우유니트, 난각두께, 난각강도, 난황색 및 농후난백 높이는 PM3, PM5가 CON 및 CP3에 비해서 높았다. 계분으로부터 암모니아, E. coli, 총호기성균, Coliform, Salmonella 균수는 CON>CP3>PM3>PM5 순서로 증가하였다. 본 결과는 B. subtillus, S. galilaeus 및 Sphingobacteriaceae로 구성된 복합생균제 0.3%가 산란율, 계란품질 개선 및 분에서 암모니아 발생을 낮추어 양계장 악취저감 효과를 갖는다는 점을 보여 준다.

This study is a summary of the complex odor proficiency testing method using the air dilution sensory method conducted for the last 7 years. Results of the homogeneity and stability test were obtained from the measurement of the standard sample for identifying the range of measurable concentration so that the complex odor proficiency testing method was established through processing the manufactured standard sample and distribution method. Standard samples were prepared using a large Teflon bag after being homogeneously mixed inside a Teflon bag. Also, a distributing container was selected with a polyester aluminum bag in order to avoid samples of the best condition from being contaminated during transport as well as being exposed to invasive odor from a sampling bag. Test results revealed that the mixture of toluene and m-Xylene was most appropriate for this proficiency testing method to the homogeneity and stability of the testing method. In addition, DMS and DMDS were the optimized samples at the outlet area. As a result, the standard method was established to address the analysis quality management to the mixed odor inspection agencies in Korea.

The purpose of this study is to produce an adsorbent material with biomass by-product that are readily visible in daily life. The biomass by-product used in the study are coffee grounds, oak leaves and chestnut peels. These biomass by-products were produced with dry, carbonization and activation treatments. The equipment for the evaluation of adsorption capacity was the batch type system to measure the concentration of test gases with the odor sensor device. Biomass by-products have been shown to improve the absorption characteristics of adsorbent through carbonization and activation. The adsorbent made with coffee grounds and chestnut peels had superior adsorption capacity to hydrogen sulfide (H2S) and complex odor (H2S & NH3) in a comparison with regular activated carbon. The odor sensor device could be used to evaluate the device of adsorption capacity of the adsorbent.

The most effective microbial strains with the best ability to reduce complex odor were isolated from earthworm and activated sludge and identified using a 16S rDNA method. The isolated strains, Staphylococcus cohnii HYC-3 and S. carnosus JYC-4, were inoculated into the odor vials that had been left for 48 hours in water containing sesame dregs, and after 3 days, the ammonia was reduced to 5 ppm and 3 ppm from the initial 25 ppm, respectively. Complex odor was reduced to 2.5 and 2.2, respectively, while the control group maintained an odor of 5. The isolates were grown in the order of 30°C > 40°C > 20°C > 10°C. For HYC-3 and JYC-4, the optimum pH was 7 and 10, respectively, and the strains grew well at neutral pH ranges. To monitor the amount of microorganisms remaining in the environment by using the strain as a preparation for odor reduction, a probe for real-time PCR was designed. Through the quantitative and sensitivity tests on the developed strains, it was found that they showed excellent sensitivity.

The purpose of this study is to investigate and compare the change of wind velocity and processing efficiency of sulfuric compounds and more complex odors. The research was conducted in a facility specializing in odor prevention applications using upgraded existing research equipment (from 30 CMM to 200 CMM) on wastewater treatment. The research equipment was installed with the purpose of removing odor from the wastewater treatment (Pasteur Factory) located in Hoengseong-gun, GangWon. To investigate the treatment efficiency of hydrogen sulfide test samples were evaluated with different blower installation positions and changes in wind speed. The wind speed at the static pressure is about 1.70~2.08 times faster than that of the static pressure, although the blower power is different. The efficacy of sulfur compounds and complex odor treatment was 91.27% and 95.20%, respectively. The study results show that it is necessary to review the design point of wind speed due to the increase in facility scale. In addition, considering the characteristics of complex odor, it is necessary to consider additional surcharges. It was determined that the facility plan for odor prevention in relation to wind velocity will be reexamined. Ongoing research will also be considered to help identify any disadvantages and solutions for the ventilator positioning, which is currently installed in the back.

The study analyzed performance assessment factors of odor sensors from 4 different manufacturers, including minimum detection limit, humidity stability and temperature stability. In the minimum detection limit assessment, only one electrochemical gas sensor was able to detect ammonia and hydrogen sulfide at the concentration of 5 ppb. The standard deviation ratio was over 10%, and it increased as humidity rose. The range of temperatures in which the electrochemical and photoionization gas sensors could function well was between 25oC and 40oC, and the sensor output values were unstable at low temperatures. Regarding the temperature stability of the metal oxide semiconductor sensor for measuring complex odors, the sensor output values dropped considerably to 0~10oC, and were similar to the concentrations of odor gases generated at 25oC. The results of the test of odor sensor outputs after temperature and humidity pre-treatment revealed that the respective stable output values at 50% humidity and 25oC were similar to the concentrations of manufactured odors. In terms of temperature and humidity stability of the NH3, H2S and Complex odor sensors, all target substances had stable output values at 25~40oC and 50~65% relative humidity, and unstable values at low temperatures and high humidity. Therefore, implementing pretreatment systems including temperature and humidity correction (25~40oC, 50~65% RH) is necessary for the stable use of odor sensors.

The purpose of this study is to confirm the removal effect of odorous gas through the multi process. The combination of Scrubber, UV and Adsorption was analyzed using the odor gas of reservoir. Analysis was carried out for six times in total and collection was made once per each process. Sampling was performed in the afternoon during August (1:00 pm~4:00 pm). Multi process has been designed to facilitates the accessories exchange. The advantage is that it facilitates the replacement of the activated carbon and it is convenient to change the type of chemical according to the type of pollution materials. As a result, for odor gas removal efficiency, ammonia 91.8%, trimethylamine 72.0%, hydrogen sulfide 99.9%, methyl mercaptan 99.9% were removed respectively. Removal efficiency of the process is the scrubber (alkali), activated carbon adsorption, scrubber (acid) and UV procedure from the highest order. Further studies on the operating method and efficiency of multi process by the change of wind speed and chemical are recommended.

The aim of this study is to analyze error cases induced during the proficiency test of certified odor measurement agencies. In the case of the homogeneity test performed in three panel groups, the geometric mean dilution factor of the site boundary PTMs(proficiency testing materials) was 1.4 ± 0.2, 1.7 ± 0.2, 1.8 ± 0.1 and that of the outlet PTMs was 3.7 ± 0.2, 3.7 ± 0.3, 3.7 ± 0.3, respectively. In the case of the stability test for 72 h, the geometric mean dilution factor of the site boundary PTMs was 1.6 ± 0.1 and that of the outlet PTMs was 3.6 ± 0.1. Among error cases induced during the proficiency test of certified odor measurement agencies, the proportion of error cases was in the order of case II(discontinuance of estimation)(40.0%) > case I(error on estimation procedure by panelist)(33.3%) > case III(miswriting of estimation result)(13.3%) > case IV(miswriting of dilution factor) and V(writing of wrong estimation result)(6.7%). Therefore, it seems likely that additional education related to error cases II and I is required.

2011년에 전국 79개 악취검사기관을 대상으로 공기희석관능법에 대한 숙련도 시험을 실시하였다. 악취방지법의 부지 경계선과 악취 배출원의 배출허용기준을 모사한 2개의 합성복합악취를 숙련도 시험물질(proficiency testing materials, PTM)로 사용 하였다. 부지 경계선 시료는 7ppm의 톨루엔과 7ppm m-자일렌의 복합악취로 구성하였으며, 배출구 시 료는 10ppm DMS (dimethyl sulfide)와 10ppm DMDS (dimethyl disulfide)의 복합악취로 구성하였다. 숙련도 시험 결과는 기준값으로 평균과 중간값을 사용하고, 목표표준편차로 일반 표준편차, 로버스트 표준편차 및 변동계수를 사용하여 Z-점수를 평가하였다. 시험결 과의 변동계수는 PTMs의 냄새강도가 증가함에 따라 감소하였다. 복합악취에 대한 숙련 도 시험 결과는 악취희석배율보다 로그 스케일의 악취지수를 사용하여 평가하는 것이 적 절했다. 두 PTMs에 대한 참여기관의 Z-점수를 변동계수, 표준편차, 그리고 로버스트 표 준편차를 사용하여 평가할 때, 참여기관의 95%가 숙련도 기준을 만족하였다. 목표 표준 편차를 변동계수의 20%로 설정하였을 때 참여기관의 만족도 비율은 부지경계와 출구 PTM 시료에 대해 각각 90%와 95%로 양호하였다. 이러한 결과들로부터 부지경계와 출 구의 복합악취를 모사한 두 합성 PTMs 모두 복합악취의 숙련도 시험물질로 적합하였다.

본 연구에서는 악취숙련도 시험을 위한 PTM 물질로 현장시료의 적용가능성을 평가하기 위하여 하수처리장에 채취한 현장시료의 안정성과 채취 균질성을 조사하였다. 또한 현장시료를 PTM으로 사용하여 71개 악취검사기관의 공기희석관능법의 숙련도 시험을 실시하였다. 다양한 설정값(참여기관 또는 기준기관의 악취지수 평균값이나 중위수)를 기준으로 3가지 Z-score 평가법(표준편차 이용한 Z-score, Robust 표준편차를 이용한 Z-score, 목표표준편차를 이용한 Z-score)으로 숙련도의 통계적 분석을 하였다. 하수처리장 농축조에서 채취한 현장시료는 2일 동안 희석배수의 변화 없이 안정적이었고, 참여기관을 4 그룹으로 나누어 순차적으로 채취한 현장시료가 균질한 것으로 평가되었다. 이는 현장악취시료가 악취 숙련도 평가를 위한 PTM 물질로 적용 가능함을 의미한다. 숙련도 시험결과의 통계적 분석을 통해 참여기관의 숙련도 만족비율은 Z-score 평가법이나 설정값의 기준(참여기관 또는 참고기관으로 선택한 3개 대학의 악취지수 평균값이나 중위수) 보다는 목표표준편차(S*ref)값에 의존하였다. 숙련도 만족비율은 S*ref 값이 증가함에 따라 증가하였으며, PTM 시료의 분석결과에 대한 변동계수(CV) 0.13에 해당하는 목표표준편차값에서 숙련도 만족비율은 약 93∼96% 수준이었다.

This study was carried out to provide the stable and homogeneous sample for the proficiency test which was applied for the olfactory dilution method of the offensive odor. For this purpose, the relationship between VOCs concentration and air dilution test results were analysed. As the results, the mixture of 7.1 ppm of toluene and m-xylene were suitable as a low level of PTM(proficiency test material) for air dilution olfactory method. In addition, time stability and homogeneity between samples were investigated through the time of 6 hr ~ 48 hr. As the results, the stability of sample concentration with GC analysis was shown as 5.1% RSD for toluene and 6.8 %RSD for xylene, respectively. The stability of sample was 5.4 %RSD in terms of air dilution olfactory method.

The purpose of this study is to investigate that the evaluation of odor analysis is affected by the classification of the agency and the general properties of the odor analysts, including gender, age, smoking behaviour, the number of participation in odor assessment, etc, so as to improve reliability and skills in terms of the result of complex odors by the air dilution methods. The sample for complex odor used the field sample which aimed at the odor analysts in the agency. The general characterizations of the odor analysts have affected the results of the odor analysis. The values of odor evaluation obtained by female odor analysts were more delicate than male, and the value of the result was reduced when above 40 s analysts conducted the evaluation. Moreover, Non-smokers perceived odor more sensitive than smokers. The more experience of odor analysis odor analysts had, The less values of the result were assessed. On the other hand, there are no differences in the value of odor evaluation depending on theclassification of institutions that participate in odor investigation. In conclusion, the selection of odor analysts considered gender, age, smoking behavior, and experience may be required to determine the improved reliability of data in odor evaluation. Ideally, Non-smokers 20~40 years old who have no dysfunction for the olfactory sense can be suitable for being optimal odor analyst.

Since 2011, proficiency test for the air dilution olfactory method started in Korea for the evaluation of the authorized odor inspection agencies’ analysis skill. For this purpose, sulfur compounds of PTMs (proficiency test materials) were made and investigated for the application to the proficiency test as a complex malodor sample. Time stability and homogeneity between samples were analysed for the PTM which was made with 10 ppm of DMS and 10 ppm of DMDS. As the results, the stability of sample concentration with GC analysis was shown around 6%RSD through the time of 6~48 hr. In addition, dilution number during the same test period appeared almost stable, less than 6%RSD in air dilution olfactory method. The reproducibility results of four laboratories showed very similar results except one lab which was caused by the elder panel characteristics.

This study was performed to obtain the emission characteristics of odor compounds generated from a livestock wastewater treatment process. The sampling of odor compounds was performed twice, on May 9th and June 14th 2006, at 4 and 5 sites in the boundary and source areas, respectively. The odor concentrations obtained from the air dilution sensory test ranged from 10 to 100 in the boundary area. Of the 5 source sites, the odor concentrations found at the pre-treatment building had the highest values, which were 14422 and 20800 for the first and second dates, respectively. To estimate the major odor compounds produced during a live wastewater process, the contributions of 12 odor compounds to the total odor were calculated from the concentration and odor threshold values of each compound. At the pre-treatment building and outlet of the activated carbon tower of the source sites, the contribution of sulfur compounds to the odor was 97%, and at the outlet of the biofilter that of NH₃ was 90%. The order of the contribution to the odor in the boundary area sites was; from highest to lowest: H₂S, C₂H₆S, i-C₅H10O, C₃H₉N, NH₃. The correlation coefficient between the theoretical odor concentration from the odor threshold of 12 odor compounds and that obtained from the air dilution sensory test was 0.73. This result indicated a limit to the correct analysis of the odor concentration obtained from the air dilution sensory test when only 12 odorous compounds at a livestock wastewater treatment process are used. The odor removal efficiency of the deodorization facilities showed that for the activation carbon tower, the odor concentration was reduced to 4% and the contributions of H₂S, C₂H₆S and NH₃, which were estimated to be the major odor compounds, were reduced to 20, 26 and 11%, respectively. With respect to the bio-filter, the removal efficiency of the odor compounds revealed an odor concentration of 0% because the major odor compounds were calculated as negative percentages.

The objective of this work was to treat complex mal-odor of food waste with micro-bubbles from enhanced wet scrubber system, where the pilot plant was operated. Micro bubbles from the enhanced reactor of venturi scrubber were successfully generated through the air atomizing process with high velocity more than 60 m/sec and played an important role in the removal of mal-odor. Mal-odor was effectively changed into the micro-bubble and treated with washing chemicals together. Through establishing two series connection of the reactors, 85.2 % removal efficiency of complex mal-odor was obtained in case of average 940 times of input air. 0.35 kg/hr of sulfuric acid, 0.188 kg/hr of sodium hydroxide and 0.043 kg/hr of hypochlorite were injected for chemical washing.

Odor control technology include absorption, adsorption, incineration and biological treatments. But, most of processes have some problems such as secondary organic acids discharge at the final odor treatment facility. In order to solve the problems for effective treatment of organic acids in odor, it is necessary to develop a new type advanced odor control technology. Some of the technology are plasma only process and plasma hybrid process as key process of the advanced technology. In this study, odor removal performance was compared DBD(Dielectric Barrier Discharge)plasma process with PCHP(plasma catalysis hybrid process) by gaseous ammonia, formaldehyde and acetic acid. Plasma only process by acetic acid obtained higher treatment efficiency above 90%, and PCHP reached its efficiency up to 96%. Acetic acid is relatively easy pollutant to control its concentration other than sulfur and nitrogen odor compounds, because it has tendency to react with water quickly. To test of the performance of DBD plasma process by applied voltage, the tests were conducted to find the dependence of experimental conditions of the applied voltage at 13 kV and 15 kV separately. With an applied voltage at 15 kV, the treatment efficiency was achieved to more higher than 13 kV from 83% to 99% on ammonia, formaldehyde and acetic acid. It seems to the odor treatment efficiency depends on the applied voltage, temperature, humidity and chemical bonding of odors.

The removal characteristics of composite odor and malodorous substances using 33 biofilters in sewage treatment facilities were investigated. The geometry mean values of composite odor and odor quotient were reduced by 52.7% and 59.2% at the outlet of the biofilters, respectively. The removal efficiencies of the biofiltes for the composite odor and odor quotient show a significant difference statistically(p=0.000<0.05). The median value of odor quotient of sulfur compounds was reduced by 69.1% at the outlet of the biofilter and the odor quotient of the sulfur compound at the inlet and outlet of the biofilter shows a significant difference statistically(p=0.000<0.05); on the other hand, those of the NH3 and trimethylamine, aldehydes, VOCs and alcohols, organic acids do not.

Odor from sewage treatment plants have the potential to cause significant annoyance and to impact the amenity. In this study, odor emission characteristics at unit process of 48 sewage treatment facilities in 39 plants were evaluated using composite odor concentration and hydrogen sulfide (H2S) concentration. The values of composite odor concentration (geometry mean) and H2S concentration (median) for sludge treatment processes are higher than those for the other treatment processes. The composite odor concentration and H2S concentration are distributed over a wide area in each process. Composite odor concentration (dilution ratio) was found to have the significant correlation with H2S concentration (p=0.000<0.05). The H2S concentration accounted for 67.1% of composite odor concentration.