검색결과

검색조건
좁혀보기
검색필터
결과 내 재검색

간행물

    분야

      발행연도

      -

        검색결과 335

        161.
        2009.10 KCI 등재 구독 인증기관 무료, 개인회원 유료
        To produce alloy powders with only SmFe single phase by reduction-diffusion (R-D) method, the effect of excess samarium oxide on the preparation of Sm-Fe alloy powder during R-D heat treatment was studied. The quantity of samarium oxide was varied from 5% to 50% whereas iron and calcium were taken 0% and 200% in excess of chemical equivalent, respectively. The pellet type mixture of samarium, iron powders and calcium granulars was subjected to heat treatment at 1100 for 5 hours. The R-D treated pellet was moved into deionized water and agitated to separate Sm-Fe alloy powders. After washing them in deionized water several times, the powders were washed with acetic acid to remove the undesired reaction products such as CaO. By these washing and acid cleaning treatment, only 0.03 wt% calcium remained in Sm-Fe alloy powders. It was also confirmed that the content of unreacted -Fe in SmFe matrix gradually decreased as the percentage of samarium oxide is increased. However, there was no significant change above 40% excess samarium oxide.
        4,000원
        162.
        2009.08 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        We report on the capacitively coupled O2 plasma etching of PMMA and polycarbonate (PC) with a diffusion pump. Plasma process variables were process pressure and CCP power at 5 sccm O2 gas flow rate. Characterization was done in order to analyze etch rate, etch selectivity, surface roughness, and morphology using stylus surface profilometry and scanning electron microscopy. Self bias decreased with increase of process pressure in the range of 25~180 mTorr. We found an important result for optimum pressure for the highest etch rate of PMMA and PC, which was 60 mTorr. PMMA and PC had etch rates of 0.46 and 0.28 μm/min under pressure conditions, respectively. More specifically, etch rates of the materials increased when the pressure changed from 25 mTorr to 60 mTorr. However, they reduced when the pressure increased further after 60 mTorr. RMS roughnesses of the etched surfaces were in the range of 2.2~2.9 nm. Etch selectivity of PMMA to a photoresist was ~1.5:1 and that of PC was ~0.9:1. Etch rate constant was about 0.04 μm/minW and 0.02 μm/minW for PMMA and PC, respectively, with the CCP power change at 5 sccm O2 and 40 mTorr process pressure. PC had more erosion on the etched sidewall than PMMA did. The OES data showed that the intensity of the oxygen atomic peak (777.196 nm) proportionally increased with the CCP power.
        4,000원
        163.
        2009.08 구독 인증기관 무료, 개인회원 유료
        동영상 UCC의 확산으로 인하여 ‘참여’와 ‘공유’의 문화생산 방식이 네티즌을 네트워크 사회의 주체로 부각시키면서 커뮤니케이션 패러다임의 변화가 가속화되고 있다. 본 논문은 동영상 UCC의 확산의 배경이 된 웹2.0 패러다임과 동영상 UCC의 현황(배경, 유형, 이용현황), 동영상 UCC의 사회문화적 영향에 대하여 논의하고, 그 결과를 바탕으로 시민 참여 매체로서의 동영상 UCC의 활성화를 위한 방안을 모색하는데 목적을 둔다. 연구결과 UCC 확산의 사회문화적 영향은 첫째, 개방과 공유를 통한 참여 중심의 프로슈머 사회 실현에 기여, 둘째, UCC의 미디어적 영향력 증가, 셋째, 계층 간의 디지털 정보격차 강화로 요약된다. UCC의 활성화를 위해서는 저작권, 초상권 등에 관한 문제, 소비자의 커뮤니케이션 확장자로의 역할 수행, 수익모델 및 보상 구조 모색, UCC의 배포 및 확산 관련 기술적, 제도적 문제 등이 선결되어야 할 과제이다. UCC의 활성화는 산업논리에 따라 시장에만 맡겨서는 안되며, UCC 문화는 공익적 영역에서도 활성화되어야 한다.
        6,600원
        166.
        2008.03 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        Fe-aluminides have the potential to replace many types of stainless steels that are currently used in structural applications. Once commercialized, it is expected that they will be twice as strong as stainless steels with higher corrosion resistance at high temperatures, while their average production cost will be approximately 10% of that of stainless steels. Self-propagating, high-temperature Synthesis (SHS) has been used to produce intermetallic and ceramic compounds from reactions between elemental constituents. The driving force for the SHS is the high thermodynamic stability during the formation of the intermetallic compound. Therefore, the advantages of the SHS method include a higher purity of the products, low energy requirements and the relative simplicity of the process. In this work, a Fe-aluminide intermetallic compound was formed from high-purity elemental Fe and Al foils via a SHS reaction in a hot press. The formation of iron aluminides at the interface between the Fe and Al foil was observed to be controlled by the temperature, pressure and heating rate. Particularly, the heating rate plays the most important role in the formation of the intermetallic compound during the SHS reaction. According to a DSC analysis, a SHS reaction appeared at two different temperatures below and above the metaling point of Al. It was also observed that the SHS reaction temperatures increased as the heating rate increased. A fully dense, well-bonded intermetallic composite sheet with a thickness of 700 μm was formed by a heat treatment at 665˚C for 15 hours after a SHS reaction of alternatively layered 10 Fe and 9 Al foils. The phases and microstructures of the intermetallic composite sheets were confirmed by EPMA and XRD analyses.
        4,000원
        167.
        2007.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The distribution of light in a randomly scattering medium can represent problems found in many area. Particularly, in the clinical application of lasers for Photodynamic therapy(PDT) or in the fluorescence spectroscopy for biological tissue, turbidity plays a very important role. The influences of fluorophor, scatterer, and absorber in turbid material by light scattering were interpreted for the scattered fluorescence intensity and wavelength. The molecular properties have been studied by laser induced fluorescence spectroscopy in scattering medium as tissue. It has been found that the effects of optical properties in scattering media could be investigated by the optical parameters(μs, μa ,μt). Experimental and Monte Carlo simulation method for modelling light transport in tissue was applied. The experimental results using a randomly distributed scattering medium were discussed and compared with those obtained through Monte Carlo simulation. It'll be also important in designing the best model for oil chemistry, medicine and application of medical engineering.
        4,000원
        171.
        2007.03 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The diffusion behavior of phenol, toluene and benzoic acid in aqueous SDS solution was examined. It showed a similar experimental results for phenol and toluene. The diffusion coefficients of the solutes were characterized by the presence of two distinct regions: below the cmc and above the cmc. For phenol and toluene, it remained approximately unchanged when the SDS concentration was below the cmc. Above the cmc there was an apparent decrease in the diffusion coefficients of the two solutes with increasing SDS concentration. However, for benzoic acid the diffusion behavior was different from that of phenol and toluene. The diffusion coefficient of benzoic acid decreased slightly with increasing SDS concentration, however the diffusion coefficient was almost constant above the cmc. For benzoic acid the diffusion behavior was dependent on the joint contribution of benzoic acid molecules as well as the benzoate ions.
        4,000원
        174.
        2006.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The atmospheric aldehyde compounds were sampled by high efficiency diffusion scrubber (HEDS) and analyzed by HPLC. The sampling and analysis process can be automated and performed in real-time by continuous sampling of HEDS. All carbonyl compounds regulated by the odor regulation law can be measured in sub-ppbv level and in real-time by the HEDS-HPLC system.
        4,000원
        176.
        2006.09 구독 인증기관·개인회원 무료
        This paper compares the effect of using different types of iron powders for the preparation of by calciothermic reduction-diffusion (CRD). Three types of iron powder were used: carbonyl, sponge and water atomized. The results show that, when immediately nitrogenated after the CRD process, prepared from sponge and water atomized iron powders yield -magnets with a high degree of texture. However, after a suitable treatment with hydrogen followed by nitrogenation, -powders made from Carbonyl iron produce magnets with the best quality regarding coercivity, remanence and degree of texture.
        178.
        2006.04 구독 인증기관·개인회원 무료
        In this study, the diffusion behaviors of C and Co in liquid phase sintering of WC-Co system were investigated whether these two components diffused in the same direction in case of having opposite gradient each other with not being phase. The green compacts with controlled compositions in not being of phase and gradient composition which one is WC-5Co-1.2%C, the other is WC-XCo-0.2%C (where X = 5, 10, 15, 20, 25) were sintered at and and then the diffusion behaviors of C and Co were investigated by analyses of compositional change, also determined for microstructure and microhardness. Also, same testing was carried out on the specimens with dual layers sintered in upright and reverse positions to evaluate the effect of gravity on the diffusion in liquid Co. From the results of this study, we can find the fact that the direction of diffusion for C and Co in WC-Co system during liquid phase sintering was different and the effect of gravity for the liquid was insignificant. Also other physical properties were changed on the diffusion of elements.
        179.
        2006.04 구독 인증기관·개인회원 무료
        The error function can be calculated based on the Simpson method through a subroutine program. An integration program by FORTRAN language was made for diffusion equations of extended source with infinite extent and limited extent. The results on some alloying elements such as C, Co, Cr, Mn, Mo, Ni and V's diffusion in iron, showed the diffusion distance for Ni and Mo can only be and more distance for Co at common sintering temperature of . To refine the particle size of the added elements down to a scale of micrometers is an effective way to get homogeneous distribution.