간행물
한국분말야금학회 학술대회논문집
- 발행기관 한국분말재료학회(구 한국분말야금학회)
- 자료유형 학술대회
- 간기 부정기
- 수록기간 1993 ~ 2006
- 주제분류 공학 > 금속공학 공학 분류의 다른 간행물
- 십진분류KDC 559DDC 629
권호리스트/논문검색
한국분말야금학회 2006년도 춘계학술대회논문집 (2006년 4월) 443건
101.
2006.04
구독 인증기관·개인회원 무료
Gas-permeable metal die materials are developed using tool steel powder, packed in a mold having the insertion of orthogonally arrayed polymer wires. Linear gas-permeable channels in orthogonal array are thus developed by the burning out of the polymer wires, which yield a microstructure with wear resistance value and air permeability much larger than those of the conventional gas-permeable die material.
102.
2006.04
구독 인증기관·개인회원 무료
Cellular metals based on Iron have been intensively investigated during the last two decades. Because of the significant decreasing of the structural density of Iron based cellular structures, numerous technologies have been developed for their manufacturing. Besides the tremendous weight reduction a combination with other properties like energy and noise absorption, heat insulation and mechanical damping can be achieved. This contribution will give an overview about the latest state in Iron based cellular materials, including technologies in manufacturing, properties and potential applications.
103.
2006.04
구독 인증기관·개인회원 무료
Processing techniques for producing microcellular silicon carbide, mullite, and cordierite ceramics have been developed by a reaction method that incorporates a polysiloxane and reactive fillers. The techniques developed in this study offer substantial flexibility for producing microcellular ceramics whereby cell size, cell density, degree of interconnectivity, composition, and porosity can all be effectively controlled. It is demonstrated that the adjustment of filler composition enables the possibility of tailoring the composition and properties of the microcellular ceramics. The present results suggest that the proposed novel processing techniques are suitable for the manufacture of microcellular ceramics with high morphological uniformity.
104.
2006.04
구독 인증기관·개인회원 무료
105.
2006.04
구독 인증기관·개인회원 무료
The low-cycle fatigue performance and fracture of the P/M Ti-Fe-Mo-Al-Nd Alloys after sintering and forging have been studied. The linear regression equation of low-cycle fatigue lifetime has been obtained; the fatigue performances are objected under two different conditions. The fatigue fracture surface is analyzed by SEM. The low-cycle fatigue behavior of the P/M titanium alloy has been discussed.
106.
2006.04
구독 인증기관·개인회원 무료
107.
2006.04
구독 인증기관·개인회원 무료
The effect of WC or NbC addition on various properties of Ti(C0.7N0.3)-Ni cermets was investigated. The microstructure oj Ti(C0.7N0.3)-xWC-20Ni showed a typical core/rim structure, irrespective of the WC content, whereas the structure oj Ti(C0.7N0.3)-xNbC-20Ni was different and was dependent on the NbC content. The hardness (HV) and the fracture toughness (KIC) had a tendency to increase marginally, while the coercive force (HC) and the magnetic saturation decreased gradually with an increase in WC or NbC content in the systems studied. In addition, increasing WC content in Ti(C0.7N0.3)-xWC-20Ni system, decarburization was retarded, while denitrification was accelerated
108.
2006.04
구독 인증기관·개인회원 무료
We have studied the effect of C/Ti atomic ratio of TiCx (x=0.5, 0.75 and 1.0) raw powder on the properties of the Ti-Mo-WTiC sintered hard alloy. The decrease of C/Ti atomic ratio accelerated the densification in the sintering process. The hardness was remarkably improved up to 1350HV with decreasing the C/Ti atomic ratio because of increase of TiCx phase volume content and its fine dispersion. From the results of electro-chemical tests in acid and 3% NaCl solutions, it was obvious that every alloy had excellent corrosion resistance, which meant about 200 times better than that of WC-Co cemented carbide.
109.
2006.04
구독 인증기관·개인회원 무료
Injection molding of corrosive super engineering plastics and engineering plastics with various fillers is conducted under severe conditions and causes corrosion and wear problems. We have developed boride base cermets, which have excellent corrosion-and wear-resistances, and tried to apply them into plastic molding machine parts. In this paper, the effects of V substitution for Cr on the mechanical properties, corrosion resistance and microstructure of Ni-5.0B-51.0Mo-(17.5-X)Cr-XV (mass%) model cermets were investigated. Both transverse rupture strength (TRS) and hardness increased monotonically with increasing V content and reached 2.94GPa and at 10.0%V, respectively. The improvements of TRS and hardness were attributed to microstructural refinement.
110.
2006.04
구독 인증기관·개인회원 무료
111.
2006.04
구독 인증기관·개인회원 무료
is an extremely high alloyed PM material containing about 20 to 35 wt.% titanium based carbides. Such materials are designed to achieve a high wear resistance, but the high volume fraction of hard phases causes a comparable low ductility in case of tensile loading. In the present study the mechanical properties of different Ferro-Titanit grades (variations in chemical composition and in heat treatment) were investigated by means of tensile tests. The mechanical properties and the fracture behaviour will be related to the chemical composition, the heat treatment and the microstructure.
112.
2006.04
구독 인증기관·개인회원 무료
Conventional high-speed steels, which are carbide decentralized materials, are used for sliding parts, but they lack sufficient hardness for some applications. Improvement of surface hardness is possible for high-Cr steels through nitriding. However, nitriding P/M parts is not advisable without sealing the porosity before treatment, as they will become brittle. However, it is difficult to seal the pores with steam treatment, because high-Cr steel has a passive film on the surface. Controlling nitriding by decreasing the amount of oxygen on the surface to be nitrided, and grinding to decrease the porosity of the surface, makes it possible to produce a material that has reasonable and sufficient hardness in the required areas.
113.
2006.04
구독 인증기관·개인회원 무료
The development of Fe-based metal matrix composites (MMCs) with high content of hard phase has been approached by combining the use of advanced powder metallurgy techniques like high-energy milling (HEM), cold isostatic pressing (CIP) and vacuum sinterings. A 30% vol. of NbC particles was mixed with Fe powder by HEM in a planetary mill during 10h, characteristing the powder by the observation of morphology and microstructure by scanning electron microscopy (SEM). After of sintering process the variation of density, hardness,carbon content and the microstructural changes observed, permits to find the optimal conditions of processing. Afterwards, a heat treatment study was performed to study the hardenability of the composite.
114.
2006.04
구독 인증기관·개인회원 무료
Magnetic properties of nanostructured materials are affected by the microstructures such as grain size (or particle size), internal strain and crystal structure. Thus, it is necessary to study the synthesis of nanostructured materials to make significant improvements in their magnetic properties. In this study, nanostructured Fe-20at.%Co and Fe-50at.%Co alloy powders were prepared by hydrogen reduction from the two oxide powder mixtures, and . Furthermore, the effect of microstructure on the magnetic properties of hydrogen reduced Fe-Co alloy powders was examined using XRD, SEM, TEM, and VSM.
115.
2006.04
구독 인증기관·개인회원 무료
Tin oxide nanoparticles (n-SnO and ) were synthesized by the inert gas condensation (IGC) method under dynamic gas flow of oxygen and argon at various conditions. Transmission electron microscopy (TEM) and X-ray diffraction (XRD) method were used to analysis the size, shape and crystal structure of the produced powders. The synthesized particles were mostly amorphous and their size increased with increasing the partial pressure of oxygen in the processing chamber. The particles also became broader in size when higher oxygen pressures were applied. Low temperature annealing at in air resulted to crystallization of the amorphous n-SnO particles to .
116.
2006.04
구독 인증기관·개인회원 무료
Multilayer ceramic capacitor (MLCC) miniaturization has increased the demand for superfine powder due to its thin dielectric layer. Hydrothermally synthesized powder a pseudo-cubic phase resulting in poor dielectric properties due to size effect and hydroxyl ion inclusion in the lattice. We attempted a superfine (lower than 100 nm) highly tetragonal powder via a solvothermal method without precipitating agent. The lattice parameters and the relative amounts of tetragonal and cubic phases were determined using Rietveld refinement.
117.
2006.04
구독 인증기관·개인회원 무료
In this study, nano grain W is fabricated by Severe Plastic Deformation-Powder Metallurgy (SPD-PM) process. W powder and W-Re powder mixtures are processed by SPD-PM process, a Mechanical Milling (MM) process. As results, a nano grain structure, whose grain size is approximately 20nm, is obtained in W powder after MM for 360ks. A nano grain W compact, whose grain size 630nm, has excellent deformability above 1273K. A nano grain W-10Re compact is composed of equiaxed grain, a grain growth is restrained and has low dislocation density after the large deformation; therefore it is considered that W-Re compact shows superplasticity.
118.
2006.04
구독 인증기관·개인회원 무료
119.
2006.04
구독 인증기관·개인회원 무료
Kvackaj, Tibor, Zemko, Michal, Kuskulic, Tomas, Kocisko, Robert, Besterci, Michal, Dobatkin, Sergej V., Molnarova, Maria
In the present research work was searched the influence of severe plastic deformation (SPD) realized by ECAP (equalchannel angular pressing) on structural, mechanical and plastic properties of IF (interstitial free) steel. For physical simulation ECAP process with right angle channels was used. The ECAP process was numerical simulated (namely its course of temperature, strain and stress fields and deformation forces) by FormFEM software, too.
120.
2006.04
구독 인증기관·개인회원 무료
Optimized choice of material for two principally different types of PM components is presented. The first is characterized by high stresses in areas with high stress concentrations (for example synchronizer hubs with very sharp notches, typically <0.25mm in the pre-synchronizer slot and the inner splines). The second type has slightly larger notch radii (small spur gears and sprockets with typically notch radii between 1- 3mm). Diffusion alloyed materials are well suited for sharp notch components. Pre-alloyed materials are also well suited for applications with sharp notches if compressive residual stresses in the notch roots are created by appropriate process control. A free choice of material is available for components with the larger notch radii.
