This study was performed to analysis the concentration of TVOC, 5VOC and formaldehyde for building material of total 262 using 20L test chamber. The concentration of TVOC, 5VOC and formaldehyde were measured 1.001㎎/㎡･h, 43.032㎍/㎡･h, 0.012㎎/㎡･h, respectively. TVOC concentration of paint and floor covering occupied the largest concentration of the indoor building materials as 2.689㎎/㎡･h, 2.120㎎/㎡･h, respectively. 5VOC concentration of floor covering was measured 106.636㎍/㎡･h. Toulene and xylene were occupied the largest part of the 5VOC as 51.2% and 33.1%, respectively. The concentration of formaldehyde for furniture materials occupied the largest concentration of the indoor building material as 0.072㎎/㎡h.

"Sick car syndrome" is known as a syndrome having latent health damage caused by complex smell of the assorted chemicals such as PVC and ABS which was components of new car interior trim (sheet, dashboard, audio case, cable, safety glass, synthetic rubber, and adhesive). The impact of interior trim on VOC levels was evaluated by testing with leather or fabric trims. Concentrations of VOCs and formaldehyde (HCHO) discharged from the car interior trims (2 sheet covers and 1 headliner) fixed in the sample holder of the small chamber were analyzed quantitatively and qualitatively. Concentrations of TVOC and HCHO emitted from 3 samples increased with increasing temperature and time. Concentration of TVOC emitted from PVC foam leather was highest under experimental conditions.

돼지 페르몬성 냄새 물질을 탐색하기 위하여 tetrahydrofuran-2-yl 계 화합물들과 관측된 결합 친화력상수(Obs.p[Od]50) 사이의 정량적인 구조-활성관계(QSAR)로부터 4개 형태의 모델(2D-QSAR, HQSR, CoMFA 및 CoMSIA)들이 유도되었다. Ligand based approache로부터 최적화된 CoMFA 모델(예측성; r2cv.(q2)=0.886 및 상관성 r2RCV 0.984)이 가장 좋은 모델이었다. CoMFA 모델로부터 돼지 페르몬성 냄새 물질로 예측된 N1-allyl-N2 -(tetrahydrofuran-2-yl)methyl) oxalamide (P1), 2- (4-trimethylammoniummethylcyclohexyloxy)tetrahydrofurane (P5) 및 2- (3-trimethylammonium-methylcyclohexyloxy)tetrahydrofurane (P6) 분자들은 비교적 높은 결합 친화력 상수값(Pred.p[Od]50) =8~10)과 몇 가지 독성에 대하여 낮은 독성간을 나타내었다.

In this study, we attempt to analyze biofilter"s removal efficiency for volatile organic compounds from paint factory. this experiment conducted in a pilot plant with microorganisms immobilized polyurethane foam. 7 main components (Toulene, MEK, MIBK, o-Xylene, m-Xylene, Butyl acetate, Ethyl benzene) emitted from factory ventilation opening were analyzed. During the test period, the biofilter treated VOCs in 5 seconds (EBCT) and pressure drop was less than 30 ㎜H₂O/m in media. Removal efficiencies of all components were between 80~90% in 10 days of operation and higher than 94% after 40 days. The result of this experiment shows that biofilter can be useful technology for VOCs removal in the paint industry.

The density characteristics of aldehydes in Kumi electronic Industrial Complex are measured in the summer and autumn in this study. Considering the characteristics of Kumi, five representative monitoring sites in Kumi are selected. According to fair Korean odor method, samples are collected and analyzed from July 26th, 2005 to October, 10th. Investigation objects include formaldehyde, acetaldehyde, propionaldehyde, butyraldehyde, iso-valeraldehyde, n-valeraldehyde. 40 samples in summer and 45 samples in autumn are measured and analyzed, respectively. The results show that the mean concentrations in residential area and industrial area are both obey the below sequence: acetaldehyde＞formaldehyde＞propionaldehyde＞butyraldehyde＞iso-valeraldehyde＞n-valeraldehyde. For acetaldehyde, its monitored concentration in industrial areas and residential areas close to industrial areas is higher than other areas. However, for formaldehyde, its concentration in the residential area 3 in tends to be higher than that in industrial areas. Based on seasons, concentrations in summer with long sunshine duration are higher than those in autumn. It can be seen that the density distribution of aldehyde in Kumi industrial complexes is closely related with the widely use of alcohol-type additives for automobiles and alcohol-type fuels. Meanwhile, most of the researches on aldehyde concentrate on capital areas or petrochemical industrial areas, taking the chance of odor prevention and control law implementing, the management scheme and reduction strategies on aldehyde ought to be carried out, which are also suitable to the enterprise characteristics in other industrial areas of this study.

신나몬 속에서 추출한 식물체 정유 6종의 고구마뿌리혹선충(Meloidogyne incognita) 유충(J2)에 대한 살선충력을 9개 농도(ppm) 수준에서 24웰플레이트를 이용하여 실내검정 하였다. 그 결과 카시아오일류(cassia oils)에서 높은 살선충력이 확인되었는데, 그 중 가장 강한 활성을 보인 cassia oil의 구성 성분들을 GC-MS로 분석하였다. 이 오일에 함유된 주요 성분들은 (E)-cinnamaldehyde, benzaldehyde, α-terpenen, ρ-cymene, limonene, linalool, α-terpineol, cinnamyl alcohol, eugenol, salicylaldehyde, α-copaene, (E)-cinnamic acid, cinnamyl acetate, β-caryophyllene 등이었다. 각 성분들의 살선충력을 조사하였는데, (E)-cinnamaldehyde가 15 ppm과 10 ppm 농도에서도 99%와 57%의 살선충력을 보였다. 그래서 이것과 유사한 구조를 갖고 있는 화합물들 42종을 대상으로 200, 100, 50, 25, 10 ppm 농도에서 구조에 따른 살선충력을 비교 검정하였는데, vinyl cinnamate와 (E)-methoxcycinnamaldehyde가 10 ppm에서 각각 83%와 44%의 살선충력을 나타냈다. 이는 살선충력을 갖는 화합물들이 기본 골격으로서 C6-C3를 필요로 하고 더불어 방향성을 갖는 알킨(alkene) 또는 알데하이드 그룹을 갖고 있어야 함을 알 수 있었다. 이상의 실내실험을 통해 신나몬 속 식물체 정유들 또는 함유 화합물들이 토양 내 뿌리혹선충을 방제할 수 있는 잠재성이 매우 높은 식물군임을 확인하였다.

The objective of the present study is to investigate the increase in the functional characteristics of a substrate by the formation of a thin coating layer. Thin coating layers of have high potential because exhibits high hardness. Shock induced reaction synthesis is an attractive fabrication technique to synthesize uniform coating layer by controlling the shock wave. Ti and Si powders to form using shock induced reaction synthesis, were mixed using high-energy ball mill into small scale. The positive effect of this technique is highly functional coating layer on the substrate due to ultra fine substructure, which improves the bonding strength. These materials are in great demand as heat resisting, structural and corrosion resistant materials. Thin coating layer was successfully recovered and showed high Vickers' hardness (Hv=1183). Characterization studies on microstructure revealed a fairly uniform distribution of powders with good interfacial integrity between the powders and the substrate.

Fe-aluminides have the potential to replace many types of stainless steels that are currently used in structural applications. Once commercialized, it is expected that they will be twice as strong as stainless steels with higher corrosion resistance at high temperatures, while their average production cost will be approximately 10% of that of stainless steels. Self-propagating, high-temperature Synthesis (SHS) has been used to produce intermetallic and ceramic compounds from reactions between elemental constituents. The driving force for the SHS is the high thermodynamic stability during the formation of the intermetallic compound. Therefore, the advantages of the SHS method include a higher purity of the products, low energy requirements and the relative simplicity of the process. In this work, a Fe-aluminide intermetallic compound was formed from high-purity elemental Fe and Al foils via a SHS reaction in a hot press. The formation of iron aluminides at the interface between the Fe and Al foil was observed to be controlled by the temperature, pressure and heating rate. Particularly, the heating rate plays the most important role in the formation of the intermetallic compound during the SHS reaction. According to a DSC analysis, a SHS reaction appeared at two different temperatures below and above the metaling point of Al. It was also observed that the SHS reaction temperatures increased as the heating rate increased. A fully dense, well-bonded intermetallic composite sheet with a thickness of 700 μm was formed by a heat treatment at 665˚C for 15 hours after a SHS reaction of alternatively layered 10 Fe and 9 Al foils. The phases and microstructures of the intermetallic composite sheets were confirmed by EPMA and XRD analyses.

Fe compounds in scoria as distributed in the south-western area of Jeju Island were investigatedusing X-ray fluorescence spectroscopy, X-ray diffractometry, and 57Fe Mössbauer spectroscopy. The sampleswere prepared from four parasite volcanoes. It was found that these samples are typical basalt comprised ofSiO2, Al2O3, Fe, and silicate minerals. The Mössbauer spectra showed doublets for olivine, pyroxene, andilmenite as well as sextets for hematite and magnetite. The valence state of Fe is chiefly a 3+ charge statewith a slight 2+ charge state. It is expected that these results will add to the body of information related tothe formation mechanisms of Jeju Island.

트리아졸계 화합물 처리시 화합물의 종류에 관계없 이 초장과 절화장 및 절간길이가 단축되었으며 엽록소 함량이 증가되었다. 이러한 감소경향은 diniconazole 50mg·L−1와 tebuconazole 500 mg·L−1처리시 컸다. 화수장은 diniconazole 50mg·L−1와 tebuconazole 500 mg·L−1처리시 크게 단축되었던 반면, hexaconazole 50mg · L−1와 bitertanol 50mg · L−1 처리시에는 증가되 었다. 꽃목 굵기는 hexaconazole 50mg·L−1와 myclobutanil 150mg·L−1 처리시 굵었으며 화폭의 경우 myclobutanil 150mg ·L−1와 bitertanol 50mg·L−1 처리 시 증가되었고 tebuconazole 500 mg·L−1처리시에는 작아졌다. 생리장해 중 노심의 발생은 bitertanol 50mg·L−1 처리에 의해 증가되었다. 전체적으로 볼 때 diniconazole 50mg ·L−1와 tebuconazole 500 mg·L−1 처리시는 화수장 단축 및 엽록소 함량 증가의 긍정적 인 효과가 있었으나, 초장과 절화장이 단축되었고 화폭 이 작아지는 등의 부정적 효과도 같이 나타나 처리 시 주의를 요할 필요가 있다고 판단되었으며, 효과의 거양을 위해서는 화합물 종류의 선별, 농도와 처리시기 및 횟수의 조절이 필요할 것으로 생각되었다.

In this study, VOCs originating from vehicles were measured at 8 underground parking lots(two apartments, four department stores, and two large-scale marts) in Daejeon. The indoor air quality at underground parking lots of the department stores and marts was affected by the availability of the ventilation facility and their operation frequency. At the underground parking lots with a ventilation facility, the maximum VOCs concentration was 727㎍/㎥, and the minimum was 73.5㎍/㎥. The average concentration ratio of BTEX to TVOCs at the underground parking lots was almost constant, which was approximately 44.8%. TVOCs and BTEX were strongly correlated with a correlation coefficient (r) of 0.88. The relative ratio of benzene, toluene, ethylbenzene and xylene was 1 : 9.51 : 0.71 : 2.53, directly reflecting the influence of vehicles sources.

Microstructural evolution and the intermetallic compound (IMC) growth kinetics in an Au stud bump were studied via isothermal aging at 120, 150, and 180˚C for 300hrs. The AlAu4 phase was observed in an Al pad/Au stud interface, and its thickness was kept constant during the aging treatment. AuSn, AuSn2, and AuSn4 phases formed at interface between the Au stud and Sn. AuSn2, AuSn2/AuSn4, and AuSn phases dominantly grew as the aging time increased at 120˚C, 150˚C, and 180˚C, respectively, while (Au,Cu)6Sn5/Cu3Sn phases formed at Sn/Cu interface with a negligible growth rate. Kirkendall voids formed at AlAu4/Au, Au/Au-Sn IMC, and Cu3Sn/Cu interfaces and propagated continuously as the time increased. The apparent activation energy for the overall growth of the Au-Sn IMC was estimated to be 1.04 eV.

Anaerobic reductive dehalogenation of perchloroethene (PCE) was studied with lactate as the electron donor in a continuously stirred tank reactor (CSTR) inoculated with a mixed culture previously shown to dehalogenate vinyl chloride (VC). cis-1,2- dichloroethene (cDCE) was the dominant intermediate at relatively long cell retention times (〉56 days) and the electron acceptor to electron donor molar ratio (PCE:lactate) of 1:2. cDCE was transformed to VC completely at the PCE to lactate molar ratio of 1:4, and the final products of PCE dehalogenation were VC (80%) and ethene (20%). VC dehalogenation was inhibited by cDCE dehalogenation. Propionate produced from the fermentation of lactate might be used as electron donor for the dehalogenation. Batch experiments were performed to evaluate the effects of increased hydrogen, VC, and trichloroethene (TCE) on VC dehalogenation which is the rate-limiting step in PCE dehalogenation The addition of TCE increased the VC dehalogenaiton rate more than an increase in the H2 concentration, which suggests that the introduction of TCE induces the production of an enzyme that can comtabolize VC.

산업적으로 이용 되지 못하고 폐기되거나 임지에 버려지 는 수목으로부터 추출물을 분리하고 이들 추출물을 버섯 산업에 이용하게 된다면 그 경제적인 중요성 및 가치는 무한 하다고 판단된다. 천연물을 이용한 그린몰드 방제제의 제 조 및 사용은 해외로부터 무분별하게 유입되는 방제제 및 화학약품의 수입을 억제할 수 있을 뿐만 아니라, 버섯소비 자들에게 안전한 먹거리를 제공할 수 있으리라 판단된다. 본 연구의 목적은 버섯 균상에 침입하는 그린몰드의 생육 을 억제하는 유효화합물을 침엽수재 톱밥으로부터 획득하 기 위하여 최적의 추출방법을 도출하는 것이다. 수목 추출 물로부터 그린몰드 생장 억제 화합물을 분리하기 위하여 추출 조건에 따른 그린몰드 생장 억제에 유효한 수목 원료 의 추출 조건을 규명하였다. 미송 및 낙엽송 톱밥으로부터 분리한 추출물은 그린몰드 생장을 약 40% 수준에서 억제 하였다.

Both photoluminescence and thermal characteristics for SrAl2O4:Eu+2,Dy+3 phosphors synthesizedwith various aluminum compounds (α-Al2O3, γ-Al2O3, amorphous-Al2O3 and Al(OH)3) were investigated in thisstudy. The formation temperature of the host SrAl2O4 crystal is changed by these various aluminumcompounds, as a result of the different thermal decomposition temperature of SrCO3 phase. Among thesecompounds, the amorphous-Al2O3 phase shows the lowest formation temperature of the host SrAl2O4 crystal.The PL emission and excitation spectra of SrAl2O4:Eu+2, Dy+3 phosphor are not affected by these aluminumcompounds. After the removal of the Xenon lamp excitation (360nm), however, the excellent long-phosphorescent property of the phosphor is obtained by the amorphous-Al2O3 phase, although the decay timefor all phosphors decrease exponentially.

Novolac is widely used as the primary solid component of most photoresists in semiconductor and microelectronic devices. In this study, novolac resins were prepared by condensation of 35% formaldehyde with phenolic compounds such as m-/p-cresol, 2,5-dimethylphenol and bisphenol A in the presence of oxalic acid as catalyst. The average molecular weight (Mw) of these novolac resins has been varied on the changing of mixing ratio of m-/p-cresol/2,5-dimethylphenol/bisphenol A or formaldehyde/phenolic compound. Also, thermal properties of novolac were observed by TGA.

실내 공기는 대기와는 달리 실내 건축 자재에서 유래된 물질로 오염될 수 있다. 본 연구는 실내자재인 카펫에서 방출되는 휘발성 유기화합물의 생물학적 영향을 평가하기 위하여 수행되었다. 카펫과 자주달개비 BNL 4430 꽃차례를 환경노출시험용기에 넣고 일정시간 노출을 실시하였고 흡착관의 VOCs에 대한 화학분석을 실시하였다. 화학분석결과 카펫에서는 12종의 VOCs가 방출되는 것이 확인되었으며 이중 스틸렌(71.9μg m-3)과 톨루엔(