Variable valve timing unit, which is able to decrease environmental load and improve fuel economy is loaded onto many automobiles recently. This unit consists mainly of sprocket, housing and rotor. These parts are requested different properties according to environment. We produce sintered parts for variable valve timing unit by selecting compact, sinter process and special treatment according to demanded properties. In this paper, demanded properties of sintered parts for variable valve timing unit and adopted technique to satisfy them are presented.

In a manufacturing technique of the sintered filter, pressureless sintering method has good permeability, it is not need the binder and lubricant used on compacting process, so it has little contamination and it is easy to control the pore size and shape but the mechanical strength is low relatively and it is difficult that parts of complicate form are manufactured. In the case of manufacturing the filter by press and sintering method, in order to be satisfactory characteristic of un-pressed filter, in this study sintered metal filter fabricated by using 30-40mesh stainless steel 316L powder and additive agents. Porosity and structure of pores, permeability and mechanical strength of the sintered filter were investigated with the variation sintering conditions. Porosity was nearly constant about , density, permeability and mechanical strength were changed markedly with quantity of additive materials and sintering conditions.

Gas filtration at high temperature from industrial processes offers various advantages such as increasing process efficiency, improving heat recovery and materials resource recovery, etc. At the same time, it is an advanced environment protection technology. This paper describes a newly developed metallic filter element. The manufacturing process of sintered metallic powder and the mechanical and filtration characteristics of this filter element were investigated. In this work, the phase constituent changes of the powder during sintering were studied. The newly developed filter elements were found to have excellent corrosion resistance, good thermal resistance, high strength and high filtration efficiency.

This work presents mechanical properties and corrosion resistance of duplex stainless steels obtained through powder metallurgy starting from austenitic, martensitic powders by controlled addition of alloying elements in the right quantity to obtain the chemical composition of the structure similar to biphasic one. In the mixes preparations the Schaffler's diagram was taken into consideration. Prepared mixes of powders have been sintered in a vacuum furnace with argon backfilling. After sintering rapid cooling was applied using nitrogen. Corrosion properties have been studied through electrochemical methods in 1M NaCl.

The present paper investigates the possibilities of niobium using for the mechanical properties of the common low alloyed Cu-Ni-Mo-C sintered structural steels enhancing. On both thermodynamic and experimental bases there were demonstrated the Nb nitrides/carbides/carbonitrides preferential formation in these steels during sintering in dissociated ammonia at both common and elevated temperatures. The obtained results for fine Nb powder and 0.3% graphite additions to Distaloy AB iron base powder cold compacted and sintered in dissociated ammonia proved the expected strengthening effect, leading to higher mechanical properties of the processed steels than of the common Cu-Ni-Mo-C ones.

The use of the nickel free, high nitrogen stainless steel powder and nitriding during sintering of iron based materials have been shown as an alternative way to the conventional PM stainless steels containing nickel. Nitrogen as an alloying element for iron improves in an effective way the properties of sintered alloyed steels. The powder metallurgy route is a suitable way to introduce nitrogen into these alloys and, in particular, to produce high nitrogen (close to the solubility limit) stainless steels. The paper presents and discusses the nitriding behavior of nickel-free stainless steels produced by powder metallurgy method. Alloyed melt was atomized by nitrogen and in this way nitrogen was introduced into the powder. Further nitriding occurred during sintering in a nitrogen atmosphere. For comparison, compacts having the same composition as an alloyed powder were produced from elemental powders mixture. Sintering-nitriding behaviour of investigated materials has been controlled by dilatometry, chemical and X-Ray phase analysis and metallography. Mechanical properties of sintered compacts were also measured.

The study examines hardness pattern of SH737-2Cu-.9C samples transient liquid phase sintered at different temperatures viz. , and , heat treated by various methods and then tempered at different temperatures. Sintered samples were characterized for density and densification parameter, and austenitized at , subsequently cooled by four different methods viz. annealing, normalizing, oil and brine quenching. Hardness pattern was found minimum for air cooled and maximum for brine quenched, and samples sintered at had relatively higher hardness. The O.Q and B.Q samples were then tempered at , , and . Hardness pattern typically showed secondary hardness taking place, with maximum around .

The corrosion performance of a powder metallurgical aluminum alloy in aeronautical environments was studied for both as sintered and heat treated states. Sintered samples were obtained by uniaxial pressing of an Al-Cu-Mg prealloyed powder followed by liquid phase sintering. The heat treatments applied were T4 and T6. Corrosion behaviour was assessed by means of potentiodynamic polarization. Results for the equivalent commercial wrought counterpart, AA2024-T3, are also presented for comparison. Similar corrosion performance was observed for both as sintered and AA2024-T3 samples, while corrosion resistance of the PM materials was improved by the heat treatment, especially in the T4 state.

The influence of the internal current for the ZnO ceramics on the sintering behavior by pulse current sintering (PCS) method was investigated. To clear the dependence of inner current on the sintering behavior of ZnO ceramics, direct measurement of electric resistance of ZnO specimen under sintering by SPS device was carried out. It was observed that electric resistance of specimen decreases with increase in the temperature. The electric resistance begins to decrease from the low temperature of . The internal structure of sintered ZnO ceramics changed by the control of the internal current in the specimen using plate.

1mm-thick BLT ceramics were sintered in accordance with a bulk ceramic fabrication process. All XRD peaks detected in the sintered ceramics were indexed as the Bi-layered perovskite structure without secondary phases. Density was increased with increasing the sintering temperature up to and the maximum value was about 98% of the theoretical density. The remanent polarization (2Pr) value of BLT ceramic sintered at was approximately at the applied voltage of 4.5kV. From these results, a BLT ceramic target for plused laser deposition (PLD) system was successfully fabricated.

This paper concerned with SPS (spark plasma sintering), hot pressing of sinter nanometer WC-Co powder and discussed the density, hardness, microstructures and grain sizes of the alloys sintered. The results showed that the two sintered techniques could produce high density alloys and play well on the grain growth, but SPS could lower the sintering temperature and shorten sintering time. Besides, the hardness of the sintered cemented alloys that was dependent on the grain size and densification could also be improved.

Using microwave synthesized HAp nano powder and polymethyl methacrylate (PMMA) as a pore-forming agent, the porous biphasic calcium phosphate (BCP) ceramics were fabricated depending on the sintering temperature. The synthesized HAp powders was about 70-90 nm in diameter. In the porous sintered bodies, the pores having were homogeneously dispersed in the BCP matrix. Some amounts of pores interconnected due the necking of PMMA powders which will increase the osteoconductivity and ingrowth of bone-tissues while using as a bone substrate. As the sintering temperature increased, the relative density increased and showed the maximum value of 79.6%. From the SBF experiment, the maximum resorption of ion was observed in the sample sintered at .

The influence of porosity (P) on Young's modulus (E) and Poisson's ratio of sintered steels produced from four types of steel powders was investigated. The values of E and depend mainly on the value of P, and those were a little affected by alloying elements. The relationships between E, , and P were described as following equations: and , where subscript 0 means P = 0, and and are empirical constants. These approximate equations showed good agreement with empirical results.

For attaining optimum fatigue resistance of PM steels, high density levels are necessary. In this work, sintered steels Fe-1.5%Mo-0.6%C and Fe-1.5%Cr-0.2%Mo-0.6%C were produced with density levels of 7.1 to . Ultrasonic fatigue testing with 20 kHz was performed in push-pull mode up to 10E9 cycles. It was shown that the fatigue endurance strength is strongly improved by higher density levels, but also higher sintering temperatures are beneficial. The Cr-Mo steels proved to be superior to the plain Mo alloyed, due to a more favourable as-sintered matrix microstructure.

Recently, in spindle motors for hard disk drive (HDD) devices, fluid dynamic bearings (FDB) with herringbone grooves have come to be used instead of ball bearings due to the demand for high density recording of the devices etc. In this study, a 5-lobe bearing with high bearing stiffness using a sintered material was developed, and the bearing performance was examined by simulated calculations and experiments. As a result, it was clarified that the 5-lobe bearing had the required performance for practical use in the spindle motor for HDD

The effect of TiC content on oxidation behavior of the sintered WC-TiC-TaC alloys with 2 mass% TaC and different TiC amounts of 3-45 mass% was investigated through oxidation tests in air at 973K. As a result of the tests, it was revealed that with increasing TiC content in the alloys, mass changes caused by oxidation and thickness of the scale decreased. Thus, it is considered that the main component of the scales changed gradually from to with increasing TiC content in the alloys, and oxygen diffusion through the scale to the alloys was inhibited gradually.

Machinability and machining mechanism were examined in the case where resin impregnation treatment was conducted to the Mo-Co hardening particle dispersed iron-based sintered alloy. As a result, the force required for machining decreased significantly compared with the case where resin impregnation treatment was not conducted. This effect is considered to be attributable to the embrittlement of cutting chips produced by the minimization of the cut material deformation.