DME는 환경 친화적인 특성으로 인해 현재 전 세계적으로 주목을 받고 있다. 지금까지 DME는 매연을 적게 생산하는 청정 에너지라는 특성으로 인해 디젤 자동차의 주요 대체 에너지로서 연구되어 왔다. 이에 본 연구에서는 에틸렌 대향류 확산화염에 DME를 5%, 14% 및 30% 혼합했을 때, DME의 혼합 비율에 따른 매연의 수밀도 및 크기에 대한 영향을 조사하였다. 레이저 투과법 및 산란법을 이용해 수밀도 및 크기를 측정하였다. 그 결과 DME를 30% 혼합한 경우에는 매연이 감소한 반면, 5%와 14%의 혼합 비율에서는 매연이 증가하는 경향을 나타내었다. 이 결과는 DME가 매연 생성이 적은 청정 연료로 알려진 것과는 달리 에틸렌 확산화염 내에서는 DME의 혼합에 따라 매연 생성이 증가될 수 있다는 것을 의미한다.

본 연구는 절화 아이리스의 노화와 절화수명에 미치는 에틸렌의 영향과 이러한 에틸렌의 작용을 억제할 수 있는 STS 전처리의 효과에 대하여 알아보고자 수행하였다. 아이리스는 1mM STS 용액에 30분간 전처리한 후 0, 3mL·L−1 의 에틸렌에 24시간 노출시켰다. 봉오리 상태 에서 절화 아이리스의 절화수명은 STS 전처리후 에틸렌 에 노출된 것은 4.2일, 에틸렌에 노출되지 않았던 꽃은 4.6일 이었다. 반개화 상태에 수확한 아이리스의 절화수명 은 STS 전처리에서 길었다. 그러나 에틸렌 노출에 의해 서는 수명이 영향을 받지 않았다. 그러므로 절화 아이 리스는 외생 에틸렌에 민감하지 않음을 알 수 있었다. 봉 오리 상태에서 수확한 절화는 완전한 개화가 유도되지 않 고 노화가 일어나는 경우가 많으므로 어느 정도 개화가 진전된 꽃을 수확하는 것이 필요한 것으로 판단되었다.

In the present work, ethylene glycol-based (EG) copper oxide nanofluids were synthesized by pulsed wire evaporation method. In order to explode the pure copper wire, high voltage of 23 kV was applied to the both ends of wire and argon/oxygen gas mixture was used as reactant gas. EG-based copper oxide nanofluids with different volume fraction were prepared by controlling explosion number of copper wire. From the transmission electron microscope (TEM) image, it was found that the copper oxide nanoparticles exhibited an average diameter about 100 nm with the oxide layer of 2~3 nm. The synthesized copper oxide consists of CuO/ phases and the Brunauer Emmett Teller (BET) surface area was estimated to be . From the analyses of thermal properties, it is suggested that viscosity and thermal conductivity of EG-based copper oxide nanofluids do not show temperature-dependent behavior over the range of 20 to . On the other hand, the viscosity and thermal conductivity of EG-based copper oxide nanofluids increase with volume fraction due to the active Brownian motion of the nanoparticles, i.e., nanoconvection.

A reaction device raising a generation yield by efficiently removing water generated in an esterified reaction between diethylene glycol monoethyl ether and succinic acid with mixture of an azeotropic point was newly developed as a new product in development of more stabilized emulsifier with a semi-solid phase(cream) in an emulsified phase of interfacial activity. The bis-(diethylene glycol monoethyl ether succinate(hereinafter, called as BDGS) with a high yield of more than 95% was obtained. As this has a property containing amphoteric emulsified functions such as W/O type or O/W type, etc., and has a merit that can be used regardless of any emulsified phase, there is no need using other emulsified surfactant. therefore, as this has excellent skin wetability in the cosmetics industry, a product having a wider range in quality compatibility or cost saving, etc. as a humectant has been developed.

Pad-dry-cure 방식으로 ethylene cyanohydrin을 이용하여 견직물을 acrylonitrile화 시킬 때 건조 시간, curing 온도 및 시간, ethylene cyanohydrin 처리 농도, 처리 농도 등 조건 변화에 따른 변화와 반응양식을 규명하고자 하였다. 가공된 견직물의 FT-IR과 DSC 분석을 통하여 다음과 같은 결과를 얻었다. Curing을 에서 2분, ethylene cyanohydrin 처리 농도 5%, 처리농도 0.1%, 건조 온도를 로 하여 건조 시간 경과에 따른 견직물의 FT-IR 분석 결과, 건조 시간 경과에 따라 -OH() 특성 peak가 전부 장파장 쪽으로 shift 되어 나타났고, random coil에 의한 amide peak()는 단파장 쪽으로 shift되어 -sheet peak()와 중복되어 나타났다. 건조를 에서 3분, curing을 에서 2.5분, 농도를 0.1%로 하여 ethylene cyanohydrin 처리 농도에 따른 가공 견직물의 FT-IR 분석에서 -OH () 특성 peak에서 변화가 나타나 견직물의 -OH기가 반응에 관여하고 있는 것을 알 수 있었다. 위와 같은 조건으로 가공된 견직물의 DSC 분석에서 ethylene cyanohydrin 처리에 의해 견직물의 열분해 온도는 무처리의 에서 대략 로 상승하는 것으로 나타났다. 건조를 에서 3분, curing을 에서 2.5분, ethylene cyanohydrin 처리농도 5%로 하여 처리 농도에 따른 가공 견직물의 FT-IR 분석에서는 촉매 처리농도 0.8%일 경우를 제외하고는 -OH() 특성 peak에서 대부분 무처리와 비슷한 결과를 보여 주고 있으나, 0.8%의 경우에는 peak에 큰 변화를 나타냈다. 같은 조건에서 가공된 견직물의 DSC 분석에서, ethylene cyanohydrin 처리에 의해 견직물의 열분해 온도는 촉매농도와는 관계없이 무처리()에 비해 가공 견직물(대략 )의 열분해 온도가 상승됨을 알 수 있었다. 건조를 에서 70초, ethylene cyanohydrin 처리농도 5%, 처리농도 0.8%, Curing 시간을 2.5분으로 하고 curing 온도를 각각 110, 120, 130, 140, 150, 로 변화시켜 가공한 견직물의 FT-IR의 분석 결과, curing 온도 110, 150, 에서 -OH특성 peak의 변화가 크게 나타났다. 같은 조건으로 가공한 견직물의 DSC 분석에서는 ethylene cyanohydrin 처리에 의한 견직물의 열분해 온도는 curing 온도에 상관없이 미처리구()에 비해 전부 열분해 온도(대략 )가 상승함을 알 수 있었다.

This study was conducted to determine the influence of postharvest dipping treatment with aminoethoxyvinylglycine (AVG) on ethylene production and composition of non-cellulosic neutral sugars in cell walls of 'Tsugaru' apple fruits during storage. Fruits were harvested on August 20, soaked in AVG 50 and 75 mg L-1 solution for 5 minutes, and stored in cold storage chamber at 0±1℃ for 60 days. Fruit quality factor, ethylene productions, and cell wall component changes were investigated at 20 days interval. As a result, the fruit firmness and acid content were much higher in AVG treated fruits than those of untreated one during 60 days of cold storage. Ethylene production of AVG treated fruits was reduced to the level of 1/10 compared with untreated one. As to the change of non-cellulosic neutral sugars in the cell walls of 'Tsu- garu' fruits, the major sugar was arabinose and galactose in water, CDTA and Na2CO3 soluble fractions. The content of arabinose and galactose in untreated fruits increased as the softening of fruits was in progress, but the fruits treated with AVG showed a little change during storage, so it is predicted that these two cell wall compositional sugars were not solubilized by the treatment of AVG. Accordingly, the marketability of 'Tsu- garu' fruits could remarkably increase when soaking the fruits in AVG solution after harvest.

The objective of this study was to examine effect of ethylene removal apparatus on fruit quality of 'Niitaka' pear (Pyrus pyrifolia) in case of a double storage of apples and pears in a storage room. Ethylene and carbon dioxide concentration were efficiently decreased by the ethylene removal apparatus. Fruit weight loss was high at double storage of apples and pears (DAP) in a storage room compared with storage of pears. Fruit core browning was 5~22.5% at the fruits in DAP, but as setting ethylene removal apparatus it was not occurred till 90 days after storage. Soluble solids content and fruit peel hardness were not different among the treatments. Accordingly, a double storage of apples and pears in a storage room is possible as setting ethylene removal apparatus.

PDMS (polydimethylsiloxane) 복합막을 통한 기체분리 공정에서 다공성 지지체의 투과저항과 PDMS 코팅두께가 에틸렌/질소의 분리성능(투과도, 선택도)에 미치는 영향에 관하여 조사하였다. 이를 위해 Pinnau 등이 제시한 복합막 투과저항 모델이론식〔1〕이 사용되었다. 지지체의 투과도 또는 투과저항은 PES (polyethersulfone)/NMP(N-methyl-2-pyrrolidone) 고분자 용액의 농도를 변화시키면서 조절하였다. 복합막은 PES 지지체 위에 n-hexane에 녹인 2액형 PDMS 용액을 spin coater를 사용해 코팅하여 제조하였다. 선택층의 코팅 두께는 spin coater의 회전속도를 통해 조절하였다. 투과기체 분리특성은 단일기체 투과도 측정 장치를 통해 조사하였으며, 지지체 및 복합막의 단면구조 및 코팅두께는 SEM (scanning electron microscope)을 통하여 확인하였다 얻어진 실험결과는 복합막의 투과저항모델의 이론식과 매우 잘 일치함을 확인 할 수 있었다. 에틸렌/질소의 분리에 있어 PDMS 막 고유의 선택도를 얻기 위해서는 지지체의 투과저항과 코팅층의 최적화가 중요함을 확인하였다.

In order to investigate the effect of irradiation by 60Co-γrays as well as the e thermal treatment on the dielectric deterioration in ethylene propylene rubber, insulating material for electric cables used in atomic power plants, charging discharging current, residual built- up voltage and dielectric properties are measu discussed in this study. Variance in the characteristic of relative dielectric constant as a function of tem was observed in relatively high dose of irradiation. Since glass transition tem appeared at tens of degree Celsius below zero, the characteristic is attributed orientation polarization. Dielectric loss is generally increased, with increasing d irradiation in the characteristic of dielectric loss as a function of temperature, No d loss by thermal treatment was observed. Dielectric resistance decreases with increa of irradiation in the characteristic of charging current as a function of temperature be considered that dielectric resistance seems to be recovered by thermal treatm characteristic of discharging current as a function of time in the specimen less ir become similar to that of the unirradiated, when thermal treated. A peak is shown residual built- up voltage as a function of time, and the corresponding time of the shorten as increasing dose of irradiation. It is also observed that the corresponding the peak is lengthened by thermal treatment.

Pure and fine, two-component titanate powders (barium titanate, calcium titanate etc.) were synthesized by an ethylene glycol method. Titanium isopropoxide and other metal ionic salts were dissolved in liquid-type ethylene glycol without any precipitation. In non-aqueous system, the amount of ethylene glycol affected the solubility and homogeneity of metal cation sources in the solution. At the optimum amount of the polymer, the metal ions were dispersed effectively in solution and a homogeneous polymeric network was formed. Most of the synthesized powders had sub-micron or nano-size primary particles after calcination and the agglomerated calcined powders were easily ground by ball milling process. All synthesized titanate powders had stable crystallization behavior at low temperature and high specific surface area after ball milling. The crystallization behavior and the microstructures of the calcined powders were affected on the ethylene glycol content.

Transesterification reaction between dimethyl phthalate and ethylene glycol was kinetically investigated in the presense of various metal nitrate catalysts at 170℃. The reaction rates measured by the amount of distilled methanol from the reaction vessel. The transesterification reaction was carried out under the first order conditions respect to the concentration of dimethyl phthalate and catalyst, respectively. The over all order was 2nd. By Arrhenius plot, the activation energy was calculated as 17.4kcal/mole and 17.2kcal/mole on the transesterification reaction with zinc nitrate and lead nitrate, respectively. Apparent rate constant, k' was appeared linear about concentration of catalyst.

This study was conducted to investigate the effect of 1-methylcyclopropene (1-MCP) and ethylene-absorbent on the qualities of Prunus mume fruit. Prunus mume fruits were stored without film packaging (Cont), packed in LDPE film (Cont-P), and packed with ethylene-absorbent (Cont-PE). Fruits were treated with 1-MCP (1 ppm) for 24 hr at 1℃. After treatment, fruits were packed in LDPE film (MCP-P) and with ethylene-absorbent (MCP-PE) and then stored at 1℃ for 8 weeks. Total soluble solids increased during storage but decreased after 6 weeks while total acidity decreased during storage. Cont was almost completely decayed after 8 weeks of storage while Cont-P, Cont-PE, MCP-PE, and MCP-P were 46, 69, 83, and 5% decayed, respectively. L value decreased but a value increased during storage in all samples. Firmness of peel and flesh of samples decreased gradually for 8 weeks. Respiration rate did not show any significant difference among samples. Ethylene production of Cont showed 0.05 μL/kg/h but immediately after 1-MCP treatment, it showed 0.02 μL/kg/h. Oxalic and malic acids decreased while citric acid increased during storage; fructose and glucose substantially decreased after 8 weeks whereas sorbitol and sucrose increased upto 4 weeks and then decreased thereafter. Based on these results, packing the fruits treated with 1-MCP could extend the freshness of Prunus mume fruit.

본 연구는 에테폰과 부형제를 혼합하여 에틸렌 발생 타 블렛을 제조하였고, 에틸렌 가스 활성조건을 구명한 결과 는 다음과 같다. 온도조건별 타블렛의 에틸렌 발생량은 온 도가 높을수록 많은 발생을 보였다. Activator pH 조건별 에틸렌 발생량은 pH 7.0 및 9.0 조건에서는 발생량이 약 2 ppm으로 미미하였으나, pH 13.0에서 타블렛의 에틸렌 발생량은 Prosolv 부형제 94.05 ppm, HPMC 부형제 126.28 ppm, Crosscamellose 부형제 100.11 ppm으로 각각 나타났 다. 제조된 타블렛의 마손도는 Prosolv 부형제 0.1%, HPMC 부형제 0.3%, Crosscamellose 부형제 54.1%로 나타나 Crosscamellose 타블렛은 부적합하다고 판단되었다. 붕해 도의 경우 각각의 부형제에 따라 큰 차이를 보였으며, Prosolv 부형제 1분, HPMC 부형제 7분 이상, Crosscamellose 부형제 5분으로 각각 나타났다. 최종 선정된 부형제인 Prosolv 타블렛의 시간대별 에틸렌 발생 측정결과 가스포집 20시간 까지 에틸렌 발생량은 꾸준히 증가하였지만 20시 이후의 발생은 미미하였고 지속적인 가스 발생은 처리 후 20시간으로 나타났다.