본 연구는 축산시설 내 설치된 무창기공형 집열기의 배기 방향 및 유량 변화를 통해 벽체에 전달되는 일사를 차단, 이를 통한 냉방효과를 검증하려는 목적의 기초 연구로서 무창기공형 집열기 시험장치를 제작, 배기 유량 변화에 따른 위치별 온도 변화 및 이를 통한 열성능 평가를 수행하였다. 실험 결과, 무창기공형 집열기의 유량조건별 집열판 표면온도는 최고 27.7℃, 배기온도는 최고 약 10.9℃ 온도 차이를 확인하였다. 무창기공형 집열기의 유량조건별 열교환 유효도는 0.48∼0.62, 효율은 30%∼90%의 분포로 나타났다. 집열판 에너지는 유량이 증가함에 따라 감소, 집열기 내부 에너지는 유량이 증가함에 따라 증가하였다. 이를 통해 농업시설 외벽에 설치된 무창기공형 집열기의 여름철 미운용으로 인한 집열판 및 내부 온도상승과 이로 인한 벽체로의 열전달 등 무창기공형 집열기로 인한 역효과를 방지할 수 있을 뿐만 아니라 집열기 외부로의 강제 배기를 통해 벽체로 직접 투입되는 일사 차단을 통한 냉방효과 또한 구현할 수 있을 것으로 판단된다.

For the regeneration of diesel particulate filters (DPF) using non-thermal plasma (NTP), both cost-effectiveness and regeneration efficiency should be raised. This study compared and contrasted the physicochemical characteristics of carbon black and engine particulate matter (PM). After carbon black was put into the DPF, an experimental setup for the oxidation of PM using NTP was created. The findings showed that carbon black and PM samples had comparable oxidation traits, micronanostructures, and C/O elemental ratios. O3, the main active species in NTP, was susceptible to heat breakdown, and the rate of decomposition of O3 increases with increasing temperature. The removal effectiveness of carbon black first improved and subsequently declined with an increase in the NTP injection flow rate during offline DPF regeneration using NTP at room temperature. A relatively high carbon black removal efficiency of 85.1% was achieved at an NTP injection flow rate of 30 L/min.

Numerous factors contribute to the deterioration of reinforced concrete structures. Elevated temperatures significantly alter the composition of the concrete ingredients, consequently diminishing the concrete's strength properties. With the escalation of global CO2 levels, the carbonation of concrete structures has emerged as a critical challenge, substantially affecting concrete durability research. Assessing and predicting concrete degradation due to thermal effects and carbonation are crucial yet intricate tasks. To address this, multiple prediction models for concrete carbonation and compressive strength under thermal impact have been developed. This study employs seven machine learning algorithms—specifically, multiple linear regression, decision trees, random forest, support vector machines, k-nearest neighbors, artificial neural networks, and extreme gradient boosting algorithms—to formulate predictive models for concrete carbonation and thermal impact. Two distinct datasets, derived from reported experimental studies, were utilized for training these predictive models. Performance evaluation relied on metrics like root mean square error, mean square error, mean absolute error, and coefficient of determination. The optimization of hyperparameters was achieved through k-fold cross-validation and grid search techniques. The analytical outcomes demonstrate that neural networks and extreme gradient boosting algorithms outshine the remaining five machine learning approaches, showcasing outstanding predictive performance for concrete carbonation and thermal effect modeling.

본 연구에서는 Monopile 방식 풍력발전기 강구조물의 부식을 방지하기 위하여 S355 steel의 표면 거칠기에 따른 용사 코팅 상태에 관한 연구를 수행했다. 일차적으로는 시편별 서로 다른 표면거칠기를 부여하기 위해 밀링머신에 페이스 커터를 결합하여 시편별로 다른 조건의 Ra값 기준 표면거칠기를 부여했다. 실험 조건으로는 시편 가공 시 4가지의 회전속도(60, 400, 1200, 2000 rpm), feed rate 150(mm/min) 조건을 선정했다. 2차로는 와이어 용융 방식의 아크 용사 코팅을 실시했다. 코팅 조건으로는 분사 거리 200mm, 전압 24V, 전류 120A, 분사 압력 5bar, 와이어 삽입 속도 30g/mm, 와이어 직경 2mm이다. 용사 코팅 후 FE-SEM으로 표면을 관찰한 결과 모든 시편의 S355 면과 코팅층(아연-알루미늄) 사이에 유격이 발생하지 않고 성공적으로 안착이 되었음을 확인할 수 있었다.

This study investigates the behavior of the thermal conductivity among material properties in order to develop a thermal evaluation methodology of spent fuel assembles in a transport cask. It is inefficient to model each element of the spent fuel assembly in detail, and it is generally calculated by modeling the effective thermal conductivity (ETC). The ETC model was developed to allow a much simpler representation of a spent fuel assembly within a fuel compartment by treating the entire spent fuel rod array and the surrounding fill gas within the confines of the compartment as a homogenous solid material. The fuel rod assembly and surrounding gas are modeled with an effective conductivity that is designed to yield an overall conduction heat transfer rate that is equivalent to the combined effect of local conduction and radiation heat transfer in a plane through the assembly. When this model is applied to the transport cask, it tends to predict the cladding peak temperature lower than the results of detailed model in which the fuel rod arrangement and shape of the fuel assembly are simulated. As for the tendency of the error, the model tended to under-predict when basket temperature was lower than a certain temperature, and over-predict when it was higher. The purpose of this study is to investigate the attenuation effect of the cladding peak temperature on the related variables when the ETC model is applied to the transport cask. In addition, based on the thermal characteristics of this model, a correction factor that can compensate for this attenuation effect is presented. This correction factor is obtained by finding the difference between a separate ETC homogeneous model and a separate detailed fuel model, rather than directly applying the ETC calculated from the detailed fuel model to the transport cask.

High-temperature oxidation of a Ni-based superalloy was analyzed with samples taken from gas turbine blades, where the samples were heat-treated and thermally exposed. The effect of Cr/Ti/Al elements in the alloy on high temperature oxidation was investigated using an optical microscope, SEM/EDS, and TEM. A high-Cr/high-Ti oxide layer was formed on the blade surface under the heat-treated state considered to be the initial stage of high-temperature oxidation. In addition, a PFZ (γ’ precipitate free zone) accompanied by Cr carbide of Cr23C6 and high Cr-Co phase as a kind of TCP precipitation was formed under the surface layer. Pits of several μm depth containing high-Al content oxide was observed at the boundary between the oxide layer and PFZ. However, high temperature oxidation formed on the thermally exposed blade surface consisted of the following steps: ① Ti-oxide formation in the center of the oxide layer, ② Cr-oxide formation surrounding the inner oxide layer, and ③ Al-oxide formation in the pits directly under the Cr oxide layer. It is estimated that the Cr content of Ni-based superalloys improves the oxidation resistance of the alloy by forming dense oxide layer, but produced the σ or μ phase of TCP precipitation with the high-Cr component resulting in material brittleness.

The purpose of this study was to compare the efficiency of air and oxygen injected into the underwater non-thermal dielectric barrier discharge plasma (DBD plasma) device used to remove five types of antibiotics (tetracycline, doxycycline, oxytetracycline, clindamycin, and erythromycin) artificially contained in the fish farm discharge water. The voltage given to generate DBD plasma was 27.8 kV, and the measurement intervals were 0, 0.5, 1, 2, 4, 8, 16 and 32 minutes. Tetracycline antibiotics significantly decreased in 4 minutes when air was injected and were reduced in 30 seconds when oxygen was injected. After the introduction of air and oxygen at 32 minutes, 78.1% and 95.8% of tetracycline were removed, 77.1% and 96.3% of doxycycline were removed, and 77.1% and 95.5% of oxytetracycline were removed, respectively. In air and oxygen, 59.6% and 83.0% of clindamycin and 53.3% and 74.3% of erythromycin were removed, respectively. The two antibiotics showed lower removal efficiency than tetracyclines. In conclusion, fish farm discharge water contains five different types of antibiotics that can be reduced using underwater DBD plasma, and oxygen gas injection outperformed air in terms of removal efficiency.

This research investigated the effect of Si addition on the microstructure, mechanical properties, electric and thermal conductivity of as-extruded Al 6013 alloys. As the content of Si increased, the area fraction of the second phase increased. As the Si content increased, the average grain size decreased remarkably, from 182 (no Si addition) to 142 (1.5Si), 78 (3.0Si) and 77 μm (4.5Si) due to dynamic recrystallization by the dispersed second particles in the aluminum matrix during the hot extrusion. As the Si content increased, the yield strength and ultimate tensile strength increased. The maximum values of yield strength and ultimate tensile strength were 224 MPa and 103 MPa for the 6013-4.5Si alloy. As the amount of Si added increased, the electrical and thermal conductivity decreased. The electrical and thermal conductivity of the Al6013-4.5Si alloy were 44.0% IACS and 165.0 W/mK, respectively. The addition of Si to Al 6013 alloy had a significant effect on its thermal conductivity and mechanical properties.

A Cu-15Ag-5P filler metal (BCuP-5) is fabricated on a Ag substrate using a high-velocity oxygen fuel (HVOF) thermal spray process, followed by post-heat treatment (300oC for 1 h and 400oC for 1 h) of the HVOF coating layers to control its microstructure and mechanical properties. Additionally, the microstructure and mechanical properties are evaluated according to the post-heat treatment conditions. The porosity of the heat-treated coating layers are significantly reduced to less than half those of the as-sprayed coating layer, and the pore shape changes to a spherical shape. The constituent phases of the coating layers are Cu, Ag, and Cu-Ag-Cu3P eutectic, which is identical to the initial powder feedstock. A more uniform microstructure is obtained as the heat-treatment temperature increases. The hardness of the coating layer is 154.6 Hv (as-sprayed), 161.2 Hv (300oC for 1 h), and 167.0 Hv (400oC for 1 h), which increases with increasing heat-treatment temperature, and is 2.35 times higher than that of the conventional cast alloy. As a result of the pull-out test, loss or separation of the coating layer rarely occurs in the heat-treated coating layer.

For spent nuclear fuel transferred to dry storage facilities, it is difficult to apply safeguards approaches and long-term integrity verification due to the structural characteristics of the facility. There is a need to check the integrity of the nuclear fuel assembly before transferring it to a dry storage facility and are need to provide information on whether there are any defects. At the Korea Institute of Nuclear Nonproliferation and Control, as a non-destructive testing technology for ensuring Continuity of Knowledge (CoK) of the dry storage facilities, a methodology for reconstructing images by neutron tomographic technique from spent nuclear fuel using a He-4 gas scintillation detector was presented. It is thought that the He-4 gas scintillation detector-based technology can be used to verify the defect of the nuclear fuel assembly. This methodology must be accompanied by accurate neutron measurements. The place where the technique was conducted is surrounded by a concrete wall. Concrete contains water molecules, which can affect neutron measurements. In this study, reconstruction images based on neutron measurements and MCNP simulations are compared to verify the effects of the concrete. Neutron measurements were performed by measuring Cf-252 neutron sources in a 1/10 lab-scale TN- 32 cask with six He-4 gas scintillation detectors as an array. Neutron sources are fixed at each point in the cask, and the He-4 detector array is rotated from 0° to 360° at 10° intervals to reconstruct the image using the filtered back-projection (FBP) method. Also, in MCNP reconstructed images, there are two versions depending on whether concrete wall. The source image and ring shape were found in the measurement-based thermal neutron reconstruction image, which was similar to the simulation image that considering the concrete effects. On the other hand, in the simulation reconstruction image without the concrete, only the shape of the source was found. Thus, the effect of concrete should be considered when performing the neutron tomographic techniques using He-4 gas scintillation detectors.

Carbon nanotubes (CNTs) were added into the self-healing polyurethane materials as conductive filler, the mass fraction of carbon nanotubes was adjusted, and 1% polyaniline was doped. The conductive self-healing polyurethane composites with different carbon nanotubes content (PU)-1/3/5/8/10 were prepared, and analyzed and tested. The result shows that the permeability threshold value of the composite material is 8wt%, and the comprehensive performance of the composite material PU-8 is the best; the resistance of PU-8 is 1278Ω, PU-8P has a resistance of 1400Ω; using an infrared camera, it can be seen that the material can reach 143.3 °C under the DC current of 0.1A, reaching the temperature condition when the material is repaired; the swelling test shows that the PU-8P equilibrium swelling rate is 177%, the gel content is 52.67%, and there is no dissolution in dimethyl sulfoxide. Solvent stability is better than PU-8;DSC test shows that the glass transition temperature of the soft segment of PU-8P is 43 °C, and the glass transition temperature of the hard segment is − 55 °C, which is not much different from that of PU-8; TG test shows that the epitaxial starting temperature of PU-8P is 365 °C; the observation photo is magnified by a stereo microscope at ten times and the PU-8P sample is cut of in the middle at room temperature, applying a constant voltage of 30 V, the cracks disappeared. The material cracks realized self-healing with electricity, and the repair efficiency reached 20.5%.

노지재배 ‘부지화’ 나무의 동해를 경감시키기 위해 피복재로 타이벡, 위드스톱, 35% 차광망을 사용하여 피복재 내, 외부 온도와 상대습도 변화를 평가하였다. 한파 시 피복에 따른 보온 정도와 잎의 LT50을 조사하였다. 타이벡은 1.5m에서 피복 재 내부와 외부의 온도 차이는 낮았고 0.4m에서는 높았다. 상대습도는 주야간 차이가 컸으며 오전 6－8시에 높았다. －2℃일 때 24시간 타이벡 피복은 수관 1.5m에서 무처리보다 적산온도가 3.4℃ 높았다. 잎의 LT50은 타이벡 1.51℃, 위드스톱 1.33℃, 35% 차광망은 1.61℃로 무처리보다 낮았다. 타이벡의 수관 내 보온효과와 상대습도를 고려할 때 환기를 위한 미세한 천공 후 ‘부지화’ 나무에 피복시 동해 발생을 줄일 수 있을 것으로 보인다.

Extensive studies have been conducted on thermal conductivity of bentonite buffer materials, as it affects the safety performance of barriers engineered to contain high-level radioactive waste. Bentonite is composed of several minerals, and studies have shown that the difference in the thermal conductivity of bentonites is due to the variation in their mineral composition. However, the specific reasons contributing to the difference, especially with regard to the thermal conductivity of bentonites with similar mineral composition, have not been elucidated. Therefore, in this study, bentonites with significantly different thermal conductivities, but of similar mineral compositions, are investigated. Most bentonites contain more than 60% of montmorillonite. Therefore, it is believed that the exchangeable cations of montmorillonite could affect the thermal conductivity of bentonites. The effect of bentonite type was comparatively analyzed and was verified through the effective medium model for thermal conductivity. Our results show that Ca-type bentonites have a higher thermal conductivity than Na-type bentonites.

A heat pump system using wasted heat from thermal effluent to supply the heating energy can reduce energy consumption and emissions of greenhouse gases by greenhouse facilities nearby. The Jeju National University consortium constructed a heat pump system using the thermal effluent from the Jeju thermal power plant of KOMIPO to provide with cool or hot water to greenhouse facilities located 2.5km from the power station. In this paper, the system configuration of the heat pump system was summarized, and the results of operations for demonstration of a heating performance carried out during the winter season in 2018 were investigated. Therefore, if the heating control by supplying thermal effluent to the facility greenhouse, it can contribute to reducing the energy cost and improving quality.

본 연구는 감마선 및 전자선 조사에 의한 닭고기 원료 사료 내에 존재하는 주요 위해 미생물을 비열처리 살균 효과를 검증하기 위하여 진행되었다. 일반세균, E. coli 및 Salmonella의 위해 미생물을 분쇄 닭고기 원료사료에 접종 후 3, 5, 7, 10 kGy의 전자선과 감마선으로 조사하였다. 전자선과 감마선 모두 3 kGy의 조사 시 시험된 미생물을 검출 한계 이하로 사멸시켜 분쇄 육류 원료 사료의 경우 3 kGy의 흡수선량이 충분한 비열 살균 조건임을 보여주었다. 방사선 조사에 의한 원료 사료의 품질 지표 변화를 알아보기 위하여 분쇄 닭고기의 조사 처리 후 pH 변화, 색도 측정, 전자코 이취 분석을 수행하였다. pH와 색도의 경우 감마선 및 전자선 조사에 의해 유의미하게 변화하지 않는 것으로 나타났다. 전자코 이취 시험의 경우 감마선 조사의 경우 3 kGy의 저선량 조사부터 이취가 발생되기 시작하였으며 10 kGy 조사 시 급격하게 이취의 정도가 증가하는 것으로 나타났다. 전자선 조사 역시 3 kGy의 조사부터 이취가 발생하였으며 5 kGy의 선량 이후 흡수선량이 증가함에 따라 이취가 점진적으로 증가하였다. 본 연구 결과 3 kGy의 저선량에서도 닭고기를 원료로한 펫푸드의 비열 살균 효과를 충분하게 이루어짐을 확인하였고 품질 지표에도 부정적인 영향을 주지 않는 것으로 나타났다. 이러한 비열처리 펫푸드의 살균 기술 개발은 국내 펫푸드 시장의 활성화와 반려 동물의 복지 향상에 기여할 것으로 기대된다.

In this study, when stem cell culture solution is used as a cosmetic ingredient, one of the most prominent problems is that the ingredients generally have low thermal stability. Therefore, in this study, in order to find out how the stem cell culture medium is heated or preserved at high temperature, the effect of various effects of stem cells on the various effects of the stem cells was investigated. Investigated. As a result of the experiment, the wound healing assay confirmed that the cell migration increased after 6 hours, and after 24 hours, it was confirmed that the cell mobility was increased and cell division was promoted, thereby being concentrated. As a result of investigating the amount of transdermal water loss by preparing a cosmetic product containing stem cell culture solution, it was confirmed that the culture solution addition group showed an improvement rate of 31% compared to the non-added group, thereby helping in skin wound recovery. As a result of this, it is considered that this point should be considered when the stem cell culture medium is used as an active ingredient in cosmetics in the future.