검색결과

검색조건
좁혀보기
검색필터
결과 내 재검색

간행물

    분야

      발행연도

      -

        검색결과 307

        42.
        2020.08 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The change in pressure measurement according to the low pressure tap blockage rate of the Venturi flowmeter used in domestic nuclear power plants was approached numerically. Blockage rates were modeled dividing by 1/10dT to the downstream side of the low pressure tab to identify differential pressure changes. As a result, differential pressure increased in proportion to the blockage rate, and there was no change in differential pressure measurement at 10 to 40 percent with relatively small blockage rate, but the error rate of 50% to 0.3% or higher was shown.
        4,000원
        44.
        2020.04 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this paper, internal and external flow analysis of nozzle for a automatic bike washing machine was performed using Ansys Fluent, by varying nozzle injection pressure and angle. The pressure and velocity distributions generated at the nozzle outlet from internal flow analysis were applied for inlet condition of the external flow analysis of the nozzle. As a criterion for the cleaning efficiency, the shear stress condition provided by EHEDG[5] was used and an area of shear stress of 3 Pa or more according to the spray angle and pressure was compared. It is expected that the results of this paper will be applied to the development of automatic contactless bike washing nozzle.
        4,000원
        45.
        2020.04 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this research, a capacitance pressure sensor with graphene membrane and titanium substrate have been developed and studied as a potential robust substrate and a sensitive membrane material for micromachined devices. Mechanical lamination process combined with micromachining processes have been selected for the fabrication of the pressure sensor. Prior to the fabrication, capacitive pressure sensors based on a graphene diaphragm and titanium substrate have been designed. The fabricated pressure sensor uses a titanium substrate, a graphene film laminated with a floating movable plate, and a fixed surface micromachined back electrode of electroplated nickel. Finite element method is adopted to investigate the residual stresses formed in the process.Also, the out-of-plane strain is calculated under the pressure of the diaphragm. The sensitivity of devices manufactured using these techniques is 7.5 to 4 kPa-1, and the net capacitance change in the range of 0 to 180 kPa is 013 pF.
        4,000원
        46.
        2020.04 KCI 등재 구독 인증기관 무료, 개인회원 유료
        본 연구의 목적은 유도 허벅다리걸기 기술 발휘 시 발목 관절의 테이핑 처치가 하지 관절과 압 력중심(COP, center of pressure)에 미치는 영향을 분석하는데 있었다. 대학 유도 선수 20명(연령, 20.9±0.8세; 신장, 168.6±7.4cm; 체중, 73.5±11.6kg; 신체질량지수, 25.7±2.6kg/m2)이 참여하였으며, 발목 관절 테이핑 처치 전과 후의 2가지 조건에서 허벅다리걸기 기술 발휘 시 지지다리 관절의 각도와 압 력중심 요인을 분석하여 다음의 결과를 도출하였다. E2(t=2.411, p=.027) E4(t=2.388, p=.029)시점에서 발목 관절의 각도는 테이핑 처지 전에 비해 처치 후 발목의 각도가 통계적으로 적은 수치를 나타내었고, E2(t=-2.343, p=.032) E3(t=-4.531, p=.000)시점에서 힙 관절의 각도는 통계적으로 크게 나타났다. 그리 고 발목 관절 테이핑 처치 후 좌·우의 COP 이동은 상대를 메치는 P3 국면에서 통계적으로 크게 나타났으 며(t=2.670, p=.016), 전·후의 COP 이동은 상대의 무게 중심을 기울이는 P1 국면에서 통계적으로 적은 수 치를 나타내었다(t=2.846, p=.011). 그러므로 허벅다리걸기를 특기로 사용하는 유도 선수들은 발목 관절 테이핑으로 인해 발생하는 지지관절의 운동 기능과 COP의 이동범위를 고려하여 사용하는 것에 대하여 제 안하고자 한다.
        4,000원
        47.
        2020.04 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        Amorphous In-Ga-Zn-O (a-IGZO) thin film transistors, because of their relatively low mobility, have limits in attempts to fulfill high-end specifications for display backplanes. In-Zn-O (IZO) is a promising semiconductor material for high mobility device applications with excellent transparency to visible light region and low temperature process capability. In this paper, the effects of working pressure on the physical and electrical properties of IZO films and thin film transistors are investigated. The working pressure is modulated from 2 mTorr to 5 mTorr, whereas the other process conditions are fixed. As the working pressure increases, the extracted optical band gap of IZO films gradually decreases. Absorption coefficient spectra indicate that subgap states increase at high working pressure. Furthermore, IZO film fabricated at low working pressure shows smoother surface morphology. As a result, IZO thin film transistors with optimum conditions exhibit excellent switching characteristics with high mobility (≥ 30cm2/Vs) and large on/off ratio.
        4,000원
        48.
        2020.04 KCI 등재 구독 인증기관 무료, 개인회원 유료
        This paper suggests a nonlinear pressure consideration scheme through an unsteady pipe network analyzer for leakage detection with a portable pressure wave generator. In order to evaluate the performance of a proposal scheme, linear input pattern has been simulated and experiments had been carried out under both no leakage and one leakage conditions in a reservoir-pipeline-valve system. This method using portable pressure wave generator showed that a leakage can be detected from a reflection where a leakage is originated through time domain analysis. Meaningful similarity in pressure response between nonlinear input pattern and experimental results were found both no leakage and a leakage conditions.
        4,000원
        49.
        2020.03 KCI 등재 구독 인증기관 무료, 개인회원 유료
        This study analyzed how the installation of a pressure gauge in the indoor fire hydrant of an apartment building affected identifying pressurized water in the pipe, making it easier to conduct internal inspection on the fire suppression system, and ensuring reliability of fire suppression. The following are the study’s results: First, identifying pressurized water in the indoor firefighting pipe had a positive effect on the installation of a pressure gauge in the indoor fire hydrant. This implies that a higher level of identification of pressurized water in the indoor firefighting pipe had a positive impact on improving the installation and use of a pressure gauge in the indoor fire hydrant. Second, making it easier for the fire safety officer to inspect the fire suppression system had a positive effect on the installation of a pressure gauge in the indoor fire hydrant. This suggests that if it becomes easier for the apartment building’s stakeholder to conduct internal inspection or the firefighting facility manager to carry out inspection on the fire suppression system, it would have a positive effect on the installation of a pressure gauge in the indoor fire hydrant. Finally, ensuring reliability in fire suppression had a positive effect on the installation of a pressure gauge in the indoor fire hydrant. This implies that if it becomes easier to identify pressurized water in the indoor firefighting pipe, for the fire safety officer to conduct internal inspection, or for the firefighting facility manager to carry out inspection in accordance with the fire suppression system’s internal inspection requirements, it would increase reliability in fire suppression, making it more necessary to install a pressure gauge in the indoor fire hydrant.
        4,300원
        50.
        2020.02 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this study, the flat glass and adsorption pad were modeled using SolidWorks Simulation, to understand the deformation characteristics of the vertical flat glass by the adsorption pressure during vertical transport of LCD. The horizontal and vertical displacements and equivalent stresses of the flat glass were investigated by the structural analysis. From the displacement and stress visualization according to the adsorption pressure, the higher the adsorption pressure, the larger the glass surface protruded. The horizontal deformation of flat glass increased with increasing thickness and the vertical deformation increased with decreasing thickness. In addition, the maximum equivalent stress applied to the flat glass increased significantly as the adsorption pressure increased and the thickness decreased. As a result of the structural analysis, the thinner the thickness of the plate glass, the greater the effect on the adsorption pressure. Especially, the effect of the adsorption pressure was clearly observed at the thickness of 0.5mm.
        4,000원
        51.
        2020.02 KCI 등재 구독 인증기관 무료, 개인회원 유료
        본 연구에서는 정삼투 중공사막 모듈에서 중공사막의 가닥을 비틀어 배치하였을 때의 효과를 알아보기 위해 CFD 전산 유체 역학 프로그램을 통해 5개의 다른 각도로 비틀린 중공사막 모듈을 설계하고 시뮬레이션하여 비틀리지 않은 모듈과 비교하였다. 실험 결과, 중공사막이 비틀렸을 때, 모듈 내부의 유도 용액의 농도가 비틀리지 않을 때에 비해 고르게 분포하였 다. 모듈 입구의 압력은 중공사막의 비틀림과 관계없이 일정한 값을 보였지만 출구의 압력은 중공사막이 비틀린 정도가 커질 수록 증가하는 추세를 보였다. 출구의 압력이 높아짐에 따라 막 내부의 유체 속도가 감소하고 모듈 체류 시간이 증가하여 막 사이의 물질 교환이 원활하게 이루어질 것으로 예측된다. 이는 결과적으로 막이 비틀려 있을 때의 모듈 플럭스가 투과 수량 이 차지하는 비율이 그렇지 않을 때에 비해 2배 증가하였다.
        4,300원
        53.
        2019.10 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Heat transfer and pressure drop of horizontal heat exchangers with different configurations and installations numerically characterized. Three different heat exchangers were used and shaped as linear, wavy, and horizontal slinky, respectively. Installation depth was set from 0.5m to 3.0m and pipe spacing was ranged from 0.3m to 2.1m. The results showed that heat transfer rate and pressure drop were increased with the increase in the installation depth and the pipe spacing. The horizontal slinky heat exchanger carried more heat compared to others due to the greater effective heat transfer surface area per installation area. In terms of a ratio of heat transfer rate to pressure drop indicating the system efficiency, the linear heat exchanger performed better than others. On the other hand, the horizontal slinky heat exchanger was the most effective with respect to a ratio of heat transfer rate to installation cost.
        4,000원
        54.
        2019.10 KCI 등재 구독 인증기관 무료, 개인회원 유료
        해저 파이프라인은 자원개발을 포함한 에너지산업 및 철강산업과 연계한 고부가가치 산업으로서 상당한 관심을 받아왔다. 해저 파이프라인의 설계와 설치 프로젝트 수행을 위해서는 다양한 핵심요소기술들이 필요하다. 특히, 해저 파이프라인의 안전한 운영을 위해서는 예비커미셔닝을 통한 철저한 사전검증과정이 필수 불가결한 부분이다. 해저 파이프라인 예비커미셔닝 과정 중 하이드로테스팅 공정은 파이프라인 주위 온도변화에 크게 영향을 받는 것으로 알려져 있으나 이에 관한 이론적, 수치해석적 접근방법을 활용한 연구는 미미한 편이다. 본 연구에서는 해저 파이프라인의 예비커미셔닝 과정 중 하이드로테스팅 공정에 대해 과도열전달 해석법을 활용하여 내부 온도변화량 산정 및 이를 활용한 파이프라인 내부 압력변동량 예측법을 제시하였고 예측된 결과를 현장 실계측 데이터와 비교·검토하여 그 유효성을 입증하였다. 제안된 해석절차는 해저 파이프라인 설치 프로젝트 수행 사전단계에서부터 파이프라인 열전달 시뮬레이션을 통해 압력변동량 예측을 가능하게 함으로써 해저 파이프라인 설치 프로젝트의 생산성 향상에 크게 기여할 것으로 사료된다.
        4,000원
        55.
        2019.10 KCI 등재 구독 인증기관 무료, 개인회원 유료
        선박 및 수중구조물의 고속, 대형화 및 요구조건 강화의 추세에 따라 유동소음 예측기술의 중요성이 강조되고 있다. 항공, 철도 등의 공력소음 분야에서는 음향상사법을 이용하여 순음 및 광대역 유동소음에 대해 활발히 연구되고 있는 반면 조선해양분야에서는 수중추진기의 날개주파수소음에 대해서만 일부 고려되고 있다. 본 논문에서는 날개면 형상의 주요 유동소음발생 메커니즘 뒷날소음을 고려 가능한 FW-H Formulation 1B를 이용하여 수중추진기 및 선저부가물의 기초요소인 수중익에 대해 광대역소음 예측기법을 연구하였다. 기존의 FW-H Formulation 1B는 공기 중의 압력상관관계 모델에 기반하여 구성되어 있어 매질에 대한 일반성 및 정확도의 한계를 가지므로 수중환경에 대해 일반성을 가지는 벽면변동압력 모델로 확장하는 방법론을 제시하였다. 공기 중 날개면의 소음계측결과와 비교해 벽면변 동압력 모델을 이용할 경우 기존모델의 해석결과 대비 5 dB 이내의 오차로 정확도 관점에서의 유용성을 확인할 수 있었으며 전산유체역 학과 벽면변동압력을 이용한 수중환경의 광대역소음해석 절차를 확립하고 수중익의 광대역소음 예측을 수행하였다.
        4,000원
        57.
        2019.09 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        Cu2ZnSn(S,Se)4(CZTSSe) thin film solar cells areone of the most promising candidates for photovoltaic devices due to their earth-abundant composition, high absorption coefficient and appropriate band gap. The sputtering process is the main challenge to achieving high efficiency of CZTSSe solar cells for industrialization. In this study, we fabricated CZTSSe absorbers on Mo coated soda lime glass using different pressures during the annealing process. As an environmental strategy, the annealing process is performed with S and Se powder, without any toxic H2Se and/or H2S gases. Because CZTSSe thin films have a very narrow stable phase region, it is important to control the condition of the annealing process to achieve high efficiency of the solar cell. To identify the effect of process pressure during the sulfo-selenization, we experiment with varying initial pressure from 600 Torr to 800 Torr. We fabricate a CZTSSe thin film solar cell with 8.24 % efficiency, with 435 mV for open circuit voltage(VOC) and 36.98 mA/cm2 for short circuit current density(JSC), under a highest process pressure of 800 Torr.
        4,000원
        58.
        2019.08 KCI 등재 구독 인증기관 무료, 개인회원 유료
        This paper is concerned to develop a fluid pressure system for the control of artificial bladder urine discharge. The primary goal is to force the fluid into the space between the inner wall and the outer wall by using a pump in the artificial bladder having a double structure of inner and outer walls and to form the urine discharge pressure by the contraction of the bladder inner wall due to the movement of the fluid. The ANSYS_CFD analysis is used to confirm the delivery of fluid pressure in the artificial bladder model, and the ANSYS_FSI analysis is used to identify the deformation and internal pressure of the artificial bladder through the delivery of fluid pressure, and to identify the discharge of urine. As the design parameters of the modeling of the artificial bladder and the fluid flow field, the capacity of the flow field, and the pump pressure input value were selected.
        4,000원
        59.
        2019.08 KCI 등재 구독 인증기관 무료, 개인회원 유료
        At a two phase flow, according to gas and liquid phase flow rates, various flow regimes are developed such as bubbly, slug/plug, churn, annular, droplet flow and so on. At a two phase flow in small scaled channels, among various flow regimes, the intermittent flows such as bubbly, slug/plug flow are developed in the broad regions of two phase flow pattern map. In particular, the flow regimes are influenced by surface wettability. In a case of slug flow in hydrophobic small scaled channels, gas and liquid phases are perfectively separated by interfaces and contact line. The pressure drop of the two-phase flow is largely generated at moving contact line. Therefore, to well design two-phase flow system with small scales, it is important to estimate the pressure drop at moving contact line. In this study, on the basis of previous research, the pressure drop at moving contact line is experimentally measured for a various fluids (0-40% water-ethanol mixtures). And, the previous correlation to estimate pressure drop at moving contact line is verified by experimental data. In an addition, we discuss interfacial broken phenomena of slug flow in a minichannel. (D=1.555mm).
        4,000원
        60.
        2019.08 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        In this study, the effect of carbon equivalent and cooling rate on microstructure and hardness of A516 steels for pressure vessel is investigated. Six kinds of specimens are fabricated by varying carbon equivalent and cooling rate, and their microstructures and hardness levels are analyzed. Specimens with low carbon equivalent consist of ferrite and pearlite. As the cooling rate increases, the size of pearlite decreases slightly. The specimens with high carbon equivalent and rapid cooling rates of 10 and 20 oC/s consist of not only ferrite and pearlite but also bainite structure, such as granular bainite, acicular ferrite, and bainite ferrite. As the cooling rate increases, the volume fractions of bainite structure increase and the effective grain size decreases. The effective grain sizes of granular bainite, acicular ferrite, and bainitic ferrite are ~20, ~5, and ~10 μm, respectively. In the specimens with bainite structure, the volume fractions of acicular ferrite and bainitic ferrite, with small effective grains, increase as cooling rate increases, and so the hardness increases significantly.
        4,000원
        1 2 3 4 5