미니 토마토 ‘미니 캐롤’ 품종의 플러그 육묘시 주야간 온도조합 처리에 의한 유묘의 절간신장 및 정식후 화아분화에 미치는 영향을 조사하였다. 유묘의 초장신장에는 주간온도가 야간온도보다 크게 영향을 미쳤으며, 특히 같은 일평균기온에서 +DIF가 -DIF보다 절간신장에 영향이 더 큰 것으로 나타났다. 엽전개속도는 일평균기온이 증가할수록 빨라지는 경향이었으며, 묘의 충실도(건물중/초장) 지수는 일평균기온이 증가할수록 저하되었다. 제 1화방의 착생절위는 일평균기온이 16℃에서는 정상적으로 화아분화 되었으나 일평균기온이 증가하면서 제 1화방 착생절위도 증가하여 28℃에서는 16℃에 비해 약 4마디가 지연되었다. 정식후 절간신장은 육묘시 절간장과는 상관없이 각 처리간 차이가 인정되지 않았다. 그러나 마디수는 정식전의 마디수의 차이 그대로 유지되었다. 육묘시 -DIF 조건에서 초장이 억제된 묘라 할지라도 정식후 정상적인 생장반응을 나타내었으며, 제 1화방의 착생절위는 일평균기온(16℃)이 낮을수록 저절위(제9절)가 되는 것으로 밝혀졌다.

김등과 Kim등이 재발한 공정묘 생산용 풍동을 사용하여, 인공광하의 묘개체군내외에서 기온, 상대습도 및 포차(vapour pressure deficit) 등의 미기상 특성에 미치는 기류속도의 효과를 분석하였다. 기온차의 최고치가 초장 근처에서 나타났으며, 이러한 결과는 공정묘의 생육이 진행될수록 더욱 분명하게 나타났다. 묘개체군 내부에서는 배지 또는 엽으로부터의 증발산으로 인하여 개체군 외부에서의 기온에 비해서 0.7-l.4℃ 정도 낮게 나타났는데, 기류속도가 낮을수록 기온차가 높게 나타났다. 묘개체군 내부의 상대습도 분포에 미치는 기류속도의 영향이 매우 큰 것으로 나타났다. 기류속도가 증가할수록 묘개체군 내외에서의 상대습도차는 작게 나타났는데, 이것은 기류속도의 증가에 따라 엽에서의 water potential이 감소되었기 때문인 것으로 판단된다. 배지표면으로부터의 높이가 증가함에 따라 포차가 증가하였다. 이와 같은 결과는 수증기 유속의 흐름이 상방향으로 이루어짐을 의미하는 것이다. 생육단계에 따른 포차의 변화는 엽면적 지수가 클수록 수직방향으로의 기울기가 크게 나타났다. 한편, 후부에서의 상대습도 및 포차는 중앙부에서 보다 약간 낮게 나타났다. 기류속도에 따라 묘개체군의 수직방향 및 기류진행방향으로 기온, 상대습도 및 포차의 기울기가 크게 나타났는데, 이러한 미기상 요소의 기울기는 묘개체군의 불균일 생장을 초래할 수 있다.

Experiment was performed in a newly developed wind tunnel with light system to determine the aerodynamic resistance and eddy diffusivity above the plug stand under artificial light. Maximum air temperature appeared near the top of the plug stand under artificial light. Since Richardson number was ranged from -0.07 to +0.01, the atmosphere above the plug stand in wind tunnel was in an unstable or near- neutral stability state. The average aerodynamic resistance at rear region of plug stand was 25 % higher than that at middle region. Eddy diffusivity(KM) linearly increased with the increasing air current speed. KM at air current speed of 0.9 m.s-1 was about two times as many as that at air current speed of 0.3 m.s-1. And average KM at the rear region was 15% lower than that at the middle region. These results indicated that the diffusion of heat and mass along the direction of air current inside the plug stand was different. It might cause the lack of uniformity in the growth and quality of plug seedlings. The wind tunnel developed in this study would be useful to investigate the effects of air current speed on microclimates and the growth of plug seedlings under artificial light in a semi- closed ecosystem.

주요(主要)잔디의 plug로 잔디포(圃) 조성시(造成時) 조도(照度)가 미치는 영향(影響)을 조사(調査)한 바 그 결과(結果)는 다음과 같다. Chewings fescue와 zoysia-82는 조도(照度) 감소(減少)에 따라 초장(草長)과 엽장(葉長)은 길었고 엽폭(葉幅)은 감소(減少)하였으나, red fescue는 이식(移植) 90일(日), 120일(日) 후(後) 조사시(調査時) 9%의 조도(照度)에서의 초장(草長)과 엽장(葉長)이 30%의 조도(照度)에서 보다 더 짧았다. 세 종(種) 모두 조도(照度)가 감소(減少)함에 따라 지표면(地表面) 피복율(被覆率)이 감소(減少)하였으며 각(各) 부위별(部位別) 건물중(乾物重)도 조도(照度)의 감소(減少)에 따라 가벼워졌다. Zoysia-82는 조도(照度)의 감소(減少)에 따라 엽록소(葉綠素) a, b, 및 총(總) 엽록소함량(葉綠素含量)이 증가(增加)하였으나, red fescue와 chewings fescue는 30%의 조도(照度)에서 엽록소함량(葉綠素含量)이 가장 많은 편이었고, 엽록소(葉綠素) a/b는 chewings fescue와 red fescue는 자연광(自然光)에서 낮았으나 zoysia-82는 30%의 조도(照度)에서 가장 낮았다. Chewings fescue와 red fescue의 분얼수는 조도(照度)가 감소(減少)할수록 감소(減少)하였다. zoysia-82의 절간장(節間長)은 30%, 자연광(自然光), 9% 조도(照度) 순(順)으로 길었고, 절간직경(節間直莖)은 조도(照度)의 감소(減少)에 따라 감소(減少)하였다.

In recent years, with the increase of people’s automobile travel, the traffic has become more and more congested, and the generated automobile exhaust aggravates the environmental pollution. In order to realize the development of the concept of low carbon and environmental protection, China’s new energy vehicles have developed rapidly, and plug-in hybrid vehicles have played a crucial role in the transformation of the automobile industry. China’s plug-in hybrid vehicle industry has developed so far and has become an important production and sales country in the world. Based on this, this paper studies the current situation and existing problems of China’s plug-in hybrid electric vehicle export trade, and proposes improved countermeasures, which is conducive to improving the export competitiveness of China’s plug-in hybrid electric vehicles.

This study aimed to find a suitable size and a seedling raising stage for growing cuttings of Euonymus fortunei ‘Emerald and Gold’ using plug trays. The experimental method, involved cutting two nodes from a solitary branch of E. fortunei ‘Emerald and Gold’, and the use of 32 (143 mL/cell), 50 (70 mL/cell), 105 (18 mL/cell), 200 (13 mL/cell) plug trays. The cuttings were transplanted to trays after they were filled with a universal horticultural medium. To compare the growths, plant heights, the numbers of leaves, longest root lengths, thickness/radius ratios, dry weights, and fresh weights were measured from July to October, and statistical analyses were performed using both the two-way repeated-measures analysis of variance (ANOVA) and Tukey’s post-test. The results confirmed that the size of the plug tray and the seedling raising stage had a significant effect on the growth of E. fortunei ‘Emerald and Gold.’ In addition, the overall growth was high and the change in growth was relatively rapid in districts 50 and 105. Therefore, it can be considered appropriate to use 50 and 105 trays when growing cuttings of E. fortunei ‘Emerald and Gold’ on plug trays.

본 연구는 지황의 플러그 육묘 재배가 생산량을 증가시킬 수 있는지 평가하고, 강원도 남부지역에 플러그 육묘를 이용한 지황 재배 시 중부지역의 직파재배만큼 생산량을 늘릴 수 있는지 알아보기 위해 수행하였다. 수량의 경우 음성 육묘재배(1,376 ㎏/10a)가 가장 높았고, 그 다음으로 평창 육묘재배(1,256 ㎏ /10a), 음성 직파재배(1,253 ㎏/10a), 평창 직파재배(923 ㎏ /10a) 순으로 나타나, 강원도에서 육묘재배시에 중부지역 직파 재배만큼 생산량을 늘릴 수 있는 것으로 나타났다. 또한, 지황은 근경 굵기가 8-12 ㎜가 중품(中品), 그 이상이 상품(上品)의 등급으로 팔리는데, 재배실험지역과 재배방법에 상관없이 모두 14 ㎜가 넘어 상품성(商品性)에도 문제가 없었다. 그러므로 생산량과 품질 조건을 고려해 볼 때, 플러그 육묘 재배를 통해 생산량을 늘릴 수 있었으며, 강원도에서 플러그 육묘를 이용한 지황 재배 시 중부지방의 직파재배와 비슷한 생산이 가능할 것으로 생각된다. 그러나 본 연구결과를 적용하기에는 늘어나는 생산비와 증가되는 수익을 고려한 경제성 분석이 더 필요할 것으로 생각된다.

Background : This study was carried out to introduce Atractylodes macrocephala as a new income element in Gangwon area and to develop the technology necessary for stable quality seedling production. Methods and Results : For the production of high quality seedlings of Atractylodes macrocephala, seedling growth characteristics were investigated according to the types of plug cell size and seedling raising period. Atractylodes macrocephala seeds were sown on February 14, 2018 in 72, 105, 128, 162, and 200 plug trays. The emergence period after sowing was March 2, and the final occurrence rate was 76.6 - 79.5%. The number of days of emergence took 18 to 20 days from sowing date. Growth of seedlings tended to be better with less number of plug trays, such as seedling height, seedling width, leaf length, leaf width and leaf number. On the other hand, roots (net formation) increased rapidly as the number of plug trays increased. After 60 days, the matured seedling rate was good at 75.5 ± 8.4% for the 200 plug tray and 72.5 ± 4.1% for the 162 plug tray. The net formation ratio of matured seedling was the best in 60 days of seeding in 162 plug trays. The rooting rate was 98.0 ± 2.1 - 99.3 ± 1.2% when seeded for 60 days or more regardless of the type of plug tray. Conclusion : In order to produce efficient and stable seedlings in the cultivation of Atractylodes macrocephala in Gangwon area, it was considered to be advantageous for 60 days of seedling settling in the plug trays of more than 162 and less than 200.

Background : Panax ginseng C.A. Meyer belong to Panax species Araliaceae and a perennial plants. It grows in Far East Asia such as the Maritime province in Russia, the Manchuria reg ion of China, and the Korean peninsula. Panax ginseng C.A. Meyer is cultivated by seed sow ing or transplanting-culture, but seedling standing rate is as low as 50%. Therefore, it is impo rtant to increase seedling standing rate. This study was performed to research of plug-seedling cultivation techniques of Panax ginseng C.A. Meyer for increase of seedling standing rate. Methods and Results : Testing material, Panax ginseng C.A. Meyer seed, was sown on 5 kin ds of seedling trays (72, 105, 128, 162, 200 cells) in the middle of February 2016. It was gr own in the seedling green house in medicinal plant resources research department of Gyeongs angnam-do Agricultural Research and Extension Services. Four months after sowing, the seedli ng growth characteristics such as seedling standing rate and seedling withering rate were inves tigated. After transplanting in the mountain area of Hamyang-gun, growth characteristics of the root length, root weight, and other factors were investigated at the beginning of November. A s a result, seedling standing rates were 50.1% to 56.2% and seedling withering rates were 25. 2% to 35.9%. Among the five ports, the seedling standing rate of 105 cells and 72 cells was 56.2% and 55.7%, which were higher than others. In the case of 105 cells, however, seedling withering rate was 35.1% higher than that of 72 cells. Seedling leaf length and width were lo nger at 72, 105, 128 cells than at 162, 200 cells and seedling root length, root fresh weight and shoot fresh weight were the highest at 72 cells. Roughly, the more tray cells, the less se edling growth. After harvesting, among the five ports, root fresh weight and root dry weight per 1 hill of 128 cells were 0.36 g and 0.11 g, respectively, which were higher than those of other cells. Conclusion : The growth characteristics of Panax ginseng C.A. Meyer considering the seedling standing rate and seedling withering rate, among the five ports, 72 cells was most suitable. A mong the five ports, considering root fresh weight and root dry weight after harvesting, 128 c ells was most suitable.

Background : Teucrium veronicoides Maximowicz is a perennial plant affiliated to labiate. Ther e were many oil components such as methylchavicol, anethole, anisaldehyde, p-methoxycinnamal dehyde, 3-ocatanone and p-cymene. It has been used for indigestion, stomachache, vomit, diarrhe a in the chinese medicine field. Besides it used as medicine, it used increasingly as food additiv es, tea and air fresheners etc. This experiment was focused on plugs and planting date. That's why the plug plants are very useful for transplanting. It saves time and labor for farmer with well-management system. During the raised seeding time, they could has gotten plant health and maximum potential state. The planting date which would have something related to the growth of plug. Methods and Results : Plug plants raised in the greenhouse during 30 days. The interval of planting date was 10 days and five time planted in planting density of 60*30cm sized area with three repeat treatments. The first treatment was middle April. The last planting date was late May. Before planting period, the length of plant and the length of leaf were the highest at the middle April, respectively. The stem diameter was highest at late March. The number of leaf was the most in the late March and early April than other planting date. In the planting period, the length of plant was highest at early April. The stem diameter was also highest at that time. There were no differences on the length and the width of leaf. The number of leaf per plant was the most at the early May. The branches per plant and number of node per plant were the highest in middle April. In the respect of yield, early May had the highest dried yield than that of other treatments. It was 492.2kg/10a. The index of which was 122. The lowest was 317.2kg/10a in late May. Conclusion : About the characteristics on the growth and the yield of Teucrium veronicoides Maximowicz plug in accordance with the planting date, the yield of early May was the highest than that of other in this study. Therefore planting date of early May would have high possibility of optimum planting date.

A simple in-situ biomethane system to upgrade biogas was developed by using differential solubility of biogas which normally contains 35-45% carbon dioxide (CO2) and 55-65% methane (CH4) by volume. The biomethane system consists of mesophilic plug-flow sorghum digester coupled with a leachate recycle loop to an external CO2 stripper. The leachate produced in the mesophilic plug-flow digester flows to the stripper where dissolved CO2 is removed. Then the leachate that CO2 was completely stripped out is recycled back to the plug-flow reactor, resulting in absorbing CO2 and enriched CH4 contents in digester offgas from the mesophilic plug-flow digester. Offgas CH4 contents was correlated well with leachate recycle rates and alkalinity. To maintain a biogas methane content over 95%, 3 volume of leachate recycle per volume of reactor per day(3 v/v-d) and at the reactor alkalinity of 4 g/L as CaCO3 was required. Even at an intermittent stripping ratio up to 3 hours stripping(N2 sweep gas 700 ml/min) and 1 hour no-stripping, the offgas methane content over 95% was achieved. It thus resulted in a 25% reduction in the total energy and sweep gas consumption. The TVS removal efficiency of the biomethane system was 80 percent which corresponded to 96% of the control reactor. The leachate recycle rates directly affected methane productivity that appeared to be 0.71 v/v-d at 3 volume of leachate recycle per volume of reactor per day(3v/v-d) and at the reactor alkalinity of 4 g/L as CaCO3.

Graphene oxide (GO)-titania composites have emerged as an attractive heterogeneous photocatalyst that can enhance the photocatalytic activity of TiO2 nanoparticles owing to their potential interaction of electronic and adsorption natures. Accordingly, TiO2-GO mixtures were synthesized in this study using a simple chemical mixing process, and their heterogeneous photocatalytic activities were investigated to determine the degradation of airborne organic pollutants (benzene, ethyl benzene, and o-xylene (BEX)) under different operational conditions. The Fourier transform infrared spectroscopy results demonstrated the presence of GO for the TiO2-GO composites. The average efficiencies of the TiO2-GO mixtures for the decomposition of each component of BEX determined during the 3-h photocatalytic processes were 26%, 92%, and 96%, respectively, whereas the average efficiencies of the unmodified TiO2 powder were 3%, 8%, and 10%, respectively. Furthermore, the degradation efficiency of the unmodified TiO2 powder for all target compounds decreased during the 3-h photocatalytic processes, suggesting a potential deactivation even during such a short time period. Two operational conditions (air flow entering into the air-cleaning devices and the indoor pollution levels) were found to be important factors for the photocatalytic decomposition of BEX molecules. Taken together, these results show that a TiO2-GO mixture can be applied effectively for the purification of airborne organic pollutants when the operating conditions are optimized.

단옥수수로부터 찰옥수수로 변한 소비자들의 기호성과 홍수출하를 피하고 생산자의 소득을 높이기 위한 주년공급에 대응하기 위해서 조생종과 만생종 찰옥수수의 육묘와 이식재배에 관한 체계적인 연구가 필요한 현실이다. 본 연구는 2007년에 국립식량과학원 시험포장에서 찰옥수수의 조생종 품종 찰옥 1호와 만생종 품종 찰옥 4호를 재료로 하여 풋옥수수의 안정성 높은 이식재배법에 대한 일련의 실험을 수행한 것으로 그 결과를 요약하면 다음과 같다. 1. 육묘기간이 길어질수록 파종 후의 출사일수가 길어지는 반면, 이식후의 출사일수는 짧았는데, 출사일수는 찰옥 1호가 찰옥 4호에 비하여 9~12일, 그리고 2기작이 1기작에 비하여 12~15일 정도 짧았다. 2. 육묘 이식재배한 찰옥수수의 간장은 육묘일수가 길수록 감소하는 경향이었으며, 직파재배에서 간장은 2기작재배에서 1기작재배에 비하여 찰옥 1호는 17%, 그리고 찰옥 4호는 24% 감소하였다. 3. 이삭길이는 육묘일수가 길어질수록 다소 감소하였는데, 찰옥 1호는 1기작재배에 비하여 2기작재배에서 크게 감소하였다. 4. 상품 이삭수는 직파재배에서 2기작재배가 1기작재배에 비하여 찰옥 1호는 64% 감수하였고, 찰옥 4호는 12%로 감소하여 그 정도가 적었다. 5. 상품 이삭수로 보아 찰옥수수의 적정육묘일수는 찰옥1호는 1기작재배 15일 육묘, 2기작재배는 이식재배 보다 직파재배가 적당하고, 찰옥4호는 모든 작기에서 20일 육묘로 판단되었다.

본 연구는 2007년 국립식량과학원 시험포장에서 찰옥수수의 조생종 품종 찰옥 1호와 만생종 품종 찰옥 4호를 재료로 하여, 적정육묘 일수, 충실한 묘를 육성하기 위한 플러그셀 크기에 대한 일련의 실험을 수행한 것으로 그 결과를 요약하면 다음과 같았다. 1. 찰옥수수 묘의 묘장, 엽수 및 건물중은 파종기와 플러그셀 크기에 따라서 고도로 유의한 차이가 있었으나, 품종간에는 차이가 없었는데. 찰옥수수의 묘는 3월 파종 보다 5월과 7월 파종에서 생장속도가 빨랐다. 2. 찰옥수수 묘의 묘장과 엽수는 육묘일수가 길수록 증가하였는데, 3월 14일 파종에서는 30일 묘(21.6 cm), 5월 8일 파종에서는 15일 묘(25.5~26.9 cm), 그리고 7월 3일 파종에서는 10일 묘(21.6~24.0 cm)에서 이식에 적합한 묘장이 되었으며, 엽수는 3월 14일 파종에서는 파종 후 15~20일, 그리고 5월 8일과 7월 3일 파종에서는 파종 후 10일에 이식에 적합한 2~3매가 되었다. 3. 건물중도 육묘일수가 길어질수록 증가하였는데, 3월 14일 파종에서는 육묘 30일에 0.43g, 5월 8일 파종은 20일에 0.57~0.67g, 7월 3일 파종은 15일에 0.53g이었고, 또한 육묘일수가 길어질수록 건물중 증가속도가 2~3배 빨라졌다. 4. 묘장과 엽수로 보아 찰옥수수의 적정육묘일수는 모든 플러그셀 크기에서 3월14일 파종에서는 20일, 그리고 5월과 7월 파종에서는 10~15일이었다. 5. 찰옥수수 플러그묘의 묘장, 엽수, 엽면적 및 건물중 간에는 높은 정의 상관이 있었으나, 엽색도는 대부분의 형질과 부의 상관을 보였다.

지진으로부터 구조물의 안전을 확보하기 위하여 많은 공학자들의 연구가 계속되고 있다. 본 연구에서는 납의 이력특성을 이용하여 지진하중을 감소시키는 LRB(lead rubber bearing)의 감쇠능력에 대한 실험적 연구를 수행하였다. 납 플러그의 면적비를 주요변수로 설계한 2종류 12개의 시험체를 제작하여 변위제어시험을 시행하였다. 감쇠비 결정을 위한 이력감쇠곡선을 얻기 위하여 2개의 시험체가 한 쌍을 이루도록 배치하고 3회 반복이력시험을 수행하였다. 실험결과로부터 본 연구에서의 납 플러그 면적비가 큰 LRB는 지진시 구조물의 지진하중을 감소시키는데 충분한 감쇠비를 보유하고 있음을 알 수 있었다.

The experiment was conducted to improve the selection efficiency m the first generation through the analysis of variation pattems of major tuber characteristics when raising hybrid seedling using the different plug cell size. The correlations in related t