간행물
한국기계기술학회지 KCI 등재 Journal of the Korean Society of Mechanical Technology 韓國機械技術學會誌
- 발행기관 한국기계기술학회
- 자료유형 학술지
- 간기 격월간
- ISSN 1229-604X (Print)2092-0385 (Online)
- 수록기간 1999 ~ 2024
- 주제분류 공학 > 기계공학 공학 분류의 다른 간행물
- 십진분류KDC 550DDC 620
권호리스트/논문검색
제21권 제1호 (2019년 2월) 30건
학술연구
21.
2019.02
구독 인증기관 무료, 개인회원 유료
The cooling process in the injection molding requires the longest time. Therefore, a lot of studies have been conducted to reduce the cooling time. In particular, studies on conformal cooling channels using 3D printing are actively being conducted. In this study, the effect of the conformal cooling channel considering the hood shape instead of the conventional linear cooling channel was investigated by injection molding analysis. In the analysis results, when the conformal cooling channel was applied, the length deformation of the molded product was reduced by about 33% and the circular deformation of the hood assembled on the lens was reduced by about 7.1㎛.
4,000원
22.
2019.02
구독 인증기관 무료, 개인회원 유료
This experimental study was conducted to investigate the refrigeration cycle performance of a 10kW refrigerator unit using R404A refrigerant. The capacity, COP, and refrigeration cycle of the refrigerator unit were confirmed by changes in refrigerant charging amount and degree of superheat. The cooling capacity and COP of the refrigerator unit showed different tendency according to changes in refrigerant charging amount and degree of superheat. It was confirmed that the performance changes of the refrigerator unit were more dependent on the change in degree of superheat than the refrigerant charging amount. From the capacity, COP, pressure, and p-h diagram, the refrigeration cycle of the refrigerator unit showed the greatest capacity and COP at 4℃ for degree of superheat and 7,400g for the refrigerant charging amount.
4,000원
23.
2019.02
구독 인증기관 무료, 개인회원 유료
For the automotive application, graphene-glass composites were fabricated using E-glass fiber(GF) coated with various types of graphene nanosheets deposited by electrophoretic deposition. Graphene oxide(GO) was first synthesized using a modified Hummer’s method and its subsequent ultrasonic treatment in deionized water produced a stable stop of the GO. Glass fiber was immersed in water and GO suspension near the copper anode. The potential applied between the electrodes caused the GO to move toward the anode. In addition, the GO coated yarn was exposed to hydrazine hydrate at 100℃ to obtain a reduced graphene oxide(rGO) coating yarn. Both GO and rGO coated glass fiber yarns were used to fabricate unidirectional epoxy-based multi-scale composites by passive lay-up. The presence of a conductive rGO coating on glass fiber improves both the electrical conductivity and thermal conductivity of the composite. In addition, rGO-based epoxy-glass composites have been used to improve the dielectric constant, providing the option of using this structure for electromagnetic interference shielding.
4,000원
생산기술
24.
2019.02
구독 인증기관 무료, 개인회원 유료
Heat treatment of metals is an necessary process for obtaining properties required for metals. However, the heat treatment sector is labor intensive enough to be classified as an unwanted sector. In particular, in the case of quenching during the heat treatment, in order to select the defective product due to the collision caused by the collision between the products when the product is dropped in the oil tank during the quenching process, the labor is not concentrated on the heat treatment as the main process, It is a fact that it is put in. In this paper, in order to solve the labor - intensive nature, this paper designed and tested prototype products for the selection of defective products during the heat treatment process of the ball stud. The ball stud inspection device is divided into two parts, a ball stud supply device and an inspection device, and describes the concept design and prototype production contents. The performance of the prototype was evaluated by examining 1000 samples with 5 items. The manufactured ball stud inspection system will contribute to the relaxation of the avoidance phenomenon of the heat treatment industry and contribute to the efficiency and competitiveness of the work.
4,000원
25.
2019.02
구독 인증기관 무료, 개인회원 유료
This paper deals with the stability of industrial robot arms with six axes and six degrees of freedom. The robot arm used was IRB120, a product of ABB company, which is used in the real industry, by using the commercial “DAFUL” which is a simulation program that can analyze the dynamic behavior. DAFUL was applied to the robot arm to control the motion by applying the load to the robot arm and then the structural analysis of the robot arm was performed during the analysis time. As a result of the analysis of the robot arm, the stress and displacement acting on the elliptic model and the acting torque and force were analyzed. Based on the analysis results, stability was checked with reference to IRB120 product catalog.
4,000원
26.
2019.02
구독 인증기관 무료, 개인회원 유료
This study investigates the optimization of sectional shape with two dimensions on the rubber gasket of electric vehicle battery in order to maintain the airtightness and watertightness. For the section optimization, the shape of protruding section was analyzed as design variables and the design point was composed by the design of experiment(DOE) for the selected protruding shape. The uniaxial tensile test was carried out for the analysis of rubber gasket and five parameters of Mooney-Rivlin hyperelastic model were derived from the test data in order to construct the strain energy function for nonlinear behavior. The rubber gasket compression analysis was performed by using ANSYS of a commercial software and the performance of optimal shape was verified by performing the tests of watertightness and airtightness on the 3D rubber gasket with the derived section.
4,000원
27.
2019.02
구독 인증기관 무료, 개인회원 유료
This study was successfully achieved out the optimized system for dispersing and mixing condition of resin liquid. The flow analysis was simulated according to the shape of the impeller and the stirring tank using ANSYS software and optimized in advanced design. As a result, it was confirmed that the shape and double number of the impeller on the flow field are influenced better effects in a range of mixing and diffusion areas comparing to single number of impeller. It was considered that stirring was performed more quickly and efficiently under the condition of double numbers and saw tooth type impeller. This result can be applied practically for the mixing tank in the industrial application and avaliable used to make a new system for painting equipment.
4,000원
28.
2019.02
구독 인증기관 무료, 개인회원 유료
The A182 steel is used in the steam pressure regulator of power plant valves. Since the part is operated under high temperature and high pressure conditions, it is necessary to study the machining characteristics. In this study, EDS analysis of the tool wear shape according to the cutting condition of A182 steel was performed. The A182 steel is identified as a steel belonging to the hardest cutting material and will be used to derive the optimum cutting condition.
4,000원
29.
2019.02
구독 인증기관 무료, 개인회원 유료
The maintenance part of the CAN Bus Networks failure is very difficult due to the difficulty of the inspection and the variety of the cause of the failure. In this study, first, diagnosis process is classified into diagnosis process of non-communication in total and diagnostic process of partial communication failure. Second, based on the past fault code, we analyze the fault by analyzing the nearest fault by analyzing the faults through the array and diagram. And, if the past failure codes can not be analyzed, the CAN logger is used to collect data. After that, it is confirmed that the fault diagnosis can be performed effectively by analyzing and checking it. Through this, troubleshooting by the diagnostic process is suggested and the direction of troubleshooting that the field technicians can use for diagnosis and inspection of CAN Bus Networks is presented.
4,000원
30.
2019.02
구독 인증기관 무료, 개인회원 유료
The blood preparation is important for management and classification. Because the work bench for sorting blood is not produced domestically, we have developed a work bench to classify blood through this study. Single coil system was developed to control cooling efficiency and temperature distribution. And evaporator and heater were used to reduce condensate discharge. This allow us to maintain a constant temperature and the condensation remainder below 1L. This study is expected to expand to other bio-equipment development.
4,000원
1
2
