To analyze the pesticide residues in commercial bee pollen products in South Korea, 61 samples were collected and screened for 339 pesticides. Results revealed that approximately 34% (>LOQ) of samples were contaminated with at least one pesticide. The pesticide residue detection rates of domestic and imported samples were 31% and 44%, respectively. Furthermore, the pesticide residue detection rate of online distribution (60%) was higher than that of offline distribution (27%). Fifteen pesticides were discovered in bee pollen, and pendimethalin, chlorfenvinphos, chlorpyrifos, and fluazinam were detected in 7, 6, 3, and 2 order of frequency, respectively. Even though its concentration was low, chlorfenvinphos which is banned in food crops in the United States, European Union, and Korea, was detected in bee pollen samples commonly. Therefore, continuous investigation of pesticide residues in bee pollen products and their acceptance criteria is required for safety.

Porous ceramics are used in various industrial applications based on their physical properties, including isolation, storage, and thermal barrier properties. However, traditional manufacturing environments require additional steps to control artificial pores and limit deformities, because they rely on limited molding methods. To overcome this drawback, many studies have recently focused on fabricating porous structures using additive manufacturing techniques. In particular, the binder jet technology enables high porosity and various types of designs, and avoids the limitations of existing manufacturing processes. In this study, we investigated process optimization for manufacturing porous ceramic filters using the binder jet technology. In binder jet technology, the flowability of the powder used as the base material is an important factor, as well as compatibility with the binder in the process and for the final print. Flow agents and secondary binders were used to optimize the flowability and compatibility of the powders. In addition, the effects of the amount of added glass frit, and changes in sintering temperature on the microstructure, porosity and mechanical properties of the final printed product were investigated.

Boron carbide (B4C) is highly significant in the production of lightweight protective materials when added to aluminum owing to its exceptional mechanical properties. In this study, a method for fabricating Al-B4C composites using high-energy ball milling and directed energy deposition (DED) is presented. Al-4 wt.% B4C composites were fabricated under 21 different laser conditions to analyze the microstructure and mechanical properties at different values of laser power and scan speeds. The composites fabricated at a laser power of 600 W and the same scan speed exhibited the highest hardness and generated the fewest pores. In contrast, the composites fabricated at a laser power of 1000 W exhibited the lowest hardness and generated a significant number of large pores. This can be explained by the influence of the microstructure on the energy density at different values of laser power.

Aluminum alloys are widely utilized in diverse industries, such as automobiles, aerospace, and architecture, owing to their high specific strength and resistance to oxidation. However, to meet the increasing demands of the industry, it is necessary to design new aluminum alloys with excellent properties. Thus, a new method is required to efficiently test additively manufactured aluminum alloys with various compositions within a short period during the alloy design process. In this study, a combinatory approach using a direct energy deposition system for metal 3D printing process with a dual feeder was employed. Two types of aluminum alloy powders, namely Al6061 and Al-12Cu, were utilized for the combinatory test conducted through 3D printing. Twelve types of Al-Si-Cu-Mg alloys were manufactured during this combinatory test, and the relationship between their microstructures and properties was investigated.

Metal additive manufacturing (AM) has transformed conventional manufacturing processes by offering unprecedented opportunities for design innovation, reduced lead times, and cost-effective production. Aluminum alloy, a material used in metal 3D printing, is a representative lightweight structural material known for its high specific strength and corrosion resistance. Consequently, there is an increasing demand for 3D printed aluminum alloy components across industries, including aerospace, transportation, and consumer goods. To meet this demand, research on alloys and process conditions that satisfy the specific requirement of each industry is necessary. However, 3D printing processes exhibit different behaviors of alloy elements owing to rapid thermal dynamics, making it challenging to predict the microstructure and properties. In this study, we gathered published data on the relationship between alloy composition, processing conditions, and properties. Furthermore, we conducted a sensitivity analysis on the effects of the process variables on the density and hardness of aluminum alloys used in additive manufacturing.

We used the measurement data derived from a proton transfer reaction time-offlight mass spectrometry (PTR-ToF-MS) to ascertain the source profile of volatile organic compounds (VOCs) from 4 major industrial classifications which showed the highest emissions from a total of 26 industrial classifications of A industrial complex. Methanol (MOH) was indicated as the highest VOC in the industrial classification of fabricated metal manufacture, and it was followed by dichloromethane (DM), ethanol (EN) and acetaldehyde (AAE). In the industrial classification of printing and recording media, the emission of ethylacetate (EA) and toluene (TOL) were the highest, and were followed by acetone (ACT), ethanol (EN) and acetic acid (AA). TOL, MOH, 2-butanol (MEK) and AAE were measured at high concentrations in the classification of rubber and plastic manufacture. In the classification of sewage, wastewater and manure treatment, TOL was the highest, and it was followed by MOH, H2S, and ethylbenzene (EBZ). In future studies, the source profiles for various industrial classifications which can provide scientific evidence must be completed, and then specified mitigation plans of VOCs for each industrial classification should be established.

본 연구에서는 국내에서 유통되는 식·약공용농산물의 잔 류농약 실태를 조사하기 위해 7품목 72건 대상으로 잔류 농약을 분석했다. 시료는 QuEChERS법으로 전처리한 후 GC-MS/MS, LC-MS/MS를 이용하여 분석했다. 식·약공용 농산물 총 7품목 72건 중 42건(58.3%)에서 잔류농약이 검 출되었으며, 검출된 농산물은 복분자 1건, 구기자 14건, 대 추 9건, 오미자 10건, 모과 1건, 생강 5건, 영지버섯 2건 이었다. 그 중 구기자 2건(11.8%), 오미자 1건(7.1%), 영 지버섯 2건(100%)에서 잔류농약 허용기준을 초과하여 검 출되었다. 검출농약은 43종으로 살균제 20종 75회, 살충제 23종 58회이었으며, 살균제 carbendazim 및 tebuconazole이 각각 11회로 가장 빈번하게 검출되었다. 허용기준을 초과 하여 검출된 농약은 acetamiprid, cadusafos, chlorpyrifos, flubendiamide, fluopyram, triazophos으로 모두 잔류농약허 용기준이 설정되지 않은 PLS 항목이었다. 결론적으로 잔 류농약 검사 건수, 검출률, 검출빈도를 종합적으로 고려해 볼 때 식·약공용농산물에 대한 지속적인 잔류농약 관리가 필요한 것으로 생각된다.

Recently, in relation to climate change, many studies have been conducted to predict the potential habitat area and distribution range of tilapia and the suitability of habitat for each species. Most tilapia are tropical fish that cannot survive at water temperatures below 10 to 12°C, although some tilapia can survive at 6 to 8°C. This study predicted habitable areas and the possibility of spreading of habitat ranges of tilapia (Oreochromis niloticus and Oreochromis aureus) known to inhabit domestic streams. Due to climate change, it was found that habitats in the Geum River, Mangyeong River, Dongjin River, Seomjin River, Taehwa River, Hyeongsan River, and the flowing in East Sea were possible by 2050. In addition, it was confirmed that tilapia could inhabit the preferred lentic ecosystem such as Tamjin Lake, Naju Lake, Juam Lake, Sangsa Lake, Jinyang Lake, Junam Reservoir, and Hoedong Reservoir. In particular, in the case of tilapia, which lives in tributaries of the Geumho River, Dalseo Stream, and the Nakdong River, its range of habitat is expected to expand to the middle and lower of the Nakdong River system. Therefore, it is judged that it is necessary to prepare physical and institutional management measures to prevent the spread of the local population where tilapia currently inhabits and to prevent introduction to new habitats.

This study was conducted to analyze and compare the dry matter yield of Italian ryegrass (IRG) cultivated under monoculture and mixed culture system to recommend suitable varieties that can be cultivated. Italian ryegrass cultivars, Green Fram (GF, extremely early-maturing), Kowinearly (KE, early-maturing), Kowinmaster (KM, mild-maturing), and Hwasan 104 (H104, late-maturing), were used for mono or mixed cultivation. The average monthly temperature in Cheonan over the past 30 years tended to be similar, but that in November and March are judged to be abnormal weather. The dry matter yield of GF+H104 was significantly higher during harvest than that of GF (p<0.05). The dry matter yields of KE and KE+KM were significantly higher during harvest than the output standards of KE and KM. There was no significant difference between the dry matter yield of H104 and KM (p>0.05), but KM had the highest yield of 16,763.1 kg/ha. Analysis showed that the highest dry matter yield during IRG harvest was obtained under monoculture and KE+KM mixed culture. Because the occurrence frequency of abnormal weather such as drought during spring is increasing recently, it is judged that IRG cultivation using early and middle growth is necessary to prepare for abnormal weather.

The oyster mushroom is a widely cultivated edible mushroom in Korea. It is a regionally specialized crop in Gyeonggi-do, where 68% of the national production is produced. The present study was conducted to develop a new, highquality cultivar with stable cultivation. ‘Manseon’ is a new variety of oyster mushroom suitable for bottle culture. It was produced by mating monokaryons isolated from ‘HB-18’ and ‘P15159-16’. The optimal temperature for ‘Manseon’ mycelial growth was 26–29 °C on potato dextrose agar (PDA) medium and for primordia formation and the growth of fruit bodies the optimal temperature was 18–19 °C on sawdust medium. Spawn running required 30 d, primordia formation required 4 d, and fruit body growth in the bottle culture required 4 d. Regarding the characteristics of the fruit bodies, the pilei were round and dark grayish brown, stipe color was white, and stipe shape was short and thick. The yield per bottle was 192.7 g/1,100 cc, which was 9% higher than that of the control strain (Suhan-1ho). The physical properties of springiness, cohesiveness, gumminess, and brittleness of stipe tissue were 87.9%, 77.4%, 445.1 kgf, and 389.6 kgf, respectively.

양돈산업은 돼지고기 내 웅취발생 예방을 위한 방법으 로 수컷 자돈에게 물리적 거세를 관행적으로 실시해왔다. 그러나 동물복지에 대한 관심이 고조됨에 따라 일부 국가 들에서는 고통 최소화 물리적 거세법 권장 또는 대체 방 법에 대해 연구를 수행하고 있다. 따라서 본 연구에서는 비거세돈(EM; entire male pigs) 및 거세돈(CM; castrated male pigs)에서 이눌린의 급여가 지방조직 내 웅취물질 농도에 미치는 영향을 구명하고자 실시하였다. 시험동물 은 총 26두의 3원 교잡돈(EM, n=18; CM, n=8)을 사용하 였다. 시험 처리구는 3% 이눌린의 급여와 비급여를 설정 하여 총 4개 처리구(EM0, EM3, CM0 및 CM3)로 구성하 였다. 웅취분석을 위해 지방조직은 등지방, 목지방 및 삼 겹지방을 수집하였다. 등지방 내 인돌 농도는 EM0에 비 해 CM3에서 감소하였고(p<0.05) 목지방 및 삼겹지방에서 는 처리구간 차이가 없었다. 지방조직 내 평균 인돌 농도 는 EM0에 비해 EM3, CM0 및 CM3에서 감소하였다 (p<0.05). 등지방 내 스카톨 농도는 CM0, CM3에서 EM0 보다 감소하였다(p<0.05). 또한, 목지방 내 스카톨 농도 및 지방조직 내 평균 스카톨 농도는 CM3에서 EM0과 EM3 보다 감소가 확인되었다(p<0.05). 그러나 안드로스테논 농 도는 분석된 지방조직들 모두에서 처리구간 통계적인 차 이가 없다. 이러한 결과들은 이눌린 급여에 의해 비거세 돈의 지방 내 웅취물질 저감에 부분적인 효과를 나타냈 을 뿐만 아니라 거세돈에서도 웅취물질 감소에 긍정적인 영향을 미쳤음을 시사한다. 따라서, 본 연구결과는 물리적 인 거세가 전면 금지된다면 동물복지형 사양관리 기술개 발의 기초자료로 활용할 수 있을 것이다.

본 연구는 소맥 위주 사료에 xylanase 효소제의 첨가가 육성돈의 사양성적, 영양소 소화율, 혈액성상, 분 중 휘발 성 지방산 및 암모니아성 질소 농도에 미치는 영향을 알 아보기 위하여 실시하였다. 총 192두(4처리, 8반복, 반복당 6두)의 육성돈(25.14±0.11 kg)을 공시하여 xylanase 첨가수 준(0, 0.0125, 0.025, 0.0375%)으로 6주간 사양시험을 실시 하였다. xylanase의 첨가수준이 증가함에 따라 전체 사양 구간에서의 일당증체량(ADG), 일일사료섭취량(ADFI) 및 사료요구율(FCR)이 유의적으로 개선되는 효과를 나타냈 다(p<005). 영양소 소화율에 있어서, xylanase 첨가수준이 증가함에 따라 phase Ⅰ에서는 건물 및 에너지, phase Ⅱ 에서는 조단백질 소화율이 유의적으로 개선되었으며, 또 한 육성돈의 혈중 GLU 농도는 사료 내 xylanase의 첨가 수준이 증가함에 따라 유의적으로 증가하는 효과를 보였 다(p<0.05). 반면에, 휘발성 지방산 및 암모니아성 질소 농 도에서 xylanase의 유의적인 첨가효과는 나타나지 않았다 (p>0.05). 결론적으로, 소맥 위주의 사료 내 xylanase의 첨 가는 육성돈의 사양성적, 영양소 소화율 및 혈중 GLU 농 도를 증가시키는데 긍정적인 효과를 보였으며, 육성돈 사 료내 소맥을 주원료로 사용할 경우 xylanse의 적정 첨가 수준은 0.0375%으로 사료된다.

콘크리트 구조물은 시간이 경과함에 따라 Steel Re-bar 부식 등이 원인이 되어 주요 구조부재의 내력이 저하된다. 이 를 방지하기 위해 아연도금, 에폭시 코팅, 피복두께 증가 등의 방법이 사용되지만 근본적인 문제가 해결되지 않는다. 최근 들어 Steel Re-bar를 대체할 복합섬유에 대한 연구가 활발히 수행된다. CFRP Re-bar는 경량이며 고강도이고 내식성이 우수하다. Steel Re-bar의 임계온도는 538℃인 반면 CFRP Re-bar의 임계온도는 250℃로 화재에 취약하다. 따라서 건설현장에 적용하기 위한 내 화피복 방안이 필요하다. 본 연구에서는 콘크리트 피복두께(40, 60, 80mm), SFRM(0, 15, 30mm)두께를 변수로 CFRP Re-bar가 배 근된 표준화재 3시간 노출된 콘크리트 기둥 단면의 온도분포를 확인하고, 온도상승에 따른 소재 강도 감소를 고려하여 P-M상관 도를 도출하였다. 이를 통해 건설현장에 CFRP Re-bar를 사용하기 위한 내화피복 두께를 제안하고자 한다. 1시간 내화성능을 만 족하기 위해 콘크리트 피복두께가 60mm 필요하며, 2시간은 80mm가 필요하다. SFRM 15mm를 도포하면 400×400 단면의 경우 2 시간, 600×600과 800×800 단면의 경우 3시간 내화성능을 만족한다.

Laparoscopy instrument requires blood vessel ligator to prevent blood leakage. Clip ligation device is widely used to prevent blood loss and secure surgical vision by using blood vessel ligator. However, in order to properly install the clip to the vessel ligator and ligate the blood vessel by the ligation machine, the device is properly operated and the parts constituting the jaw areas should be ensuring sufficient strength and rigidity during the operating. Therefore, the clip binding forces were calculated through a dynamic model of the blood vessel ligator. As a result, the force satisfies the target value of 8.5 N or more regardless of the grip force positions. And structural analysis was carried out to find out the maximum resistance force at the tip of the inner shaft. The maximum load was about 45.6 N, which sufficiently satisfies the development target of 40.0 N or higher.

In order to investigate the optimal UVB (ultraviolet B) treatment conditions for vitamin D2 enhancement of freeze-dried ear mushroom, sample size (below 300 μm~whole), UV treatment temperature (30~60℃), treatment density (6.25~50.0 mg/cm2) and the samples mixing frequency (1~32 times) were treated differently. After that, chromaticity, vitamin D2 and ergosterol (vitamin D2 precursor) contents were investigated. As a result of the investigating, effective UVB treatment conditions for vitamin D2 enhancement are as follows. The sample sizes were 2~4 mm and finely crushed pieces. The treatment temperatures were 50℃ and 60℃. The treatment density was 12.5 to 25.0 mg/cm2, and the number of sample mixing was 8 times or more. As the amount of vitamin D2 increased by UVB treatment, the ergosterol content generally tended to decrease. However, under some UVB treatment conditions, the vitamin D2 content was not high despite the decrease of ergosterol content. Under the conditions set in this experiment, it was possible to obtain ear mushrooms with enhanced vitamin D2 up to 26,968.7 μg/100 g. Therefore, it is thought that the ear mushroom is highly likely to be used as a vitamin D source and nutritionally fortified food ingredient.

This study aimed to investigate the protective effect of enzymatically modified stevia (EMS) on C2C12 cell-based model of dexamethasone (DEX)-induced muscle atrophy to provide baseline data for utilizing EMS in functional health products. C2C12 cells with DEX-induced muscle atrophy were treated with EMS (10, 50, and 100 μg/mL) for 24 h. C2C12 cells were treated with EMS and DEX to test their effects on cell viability and myotube formation (myotube diameter and fusion index), and analyze the expression of muscle strengthening or degrading protein markers. Schisandra chinensis Extract, a common functional ingredient, was used as a positive control. EMS did not show any cytotoxic effect at all treatment concentrations. Moreover, it exerted protective effects on C2C12 cell-based model of DEX-induced muscle atrophy at all concentrations. In addition, the positive effect of EMS on myotube formation was confirmed based on the measurement and comparison of the fusion index and myotube diameter when compared with myotubes treated with DEX alone. EMS treatment reduced the expression of muscle cell degradation-related proteins Fbx32 and MuRF1, and increased the expression of muscle strengthening and synthesis related proteins SIRT1 and p- Akt/Akt. Thus, EMS is a potential ingredient for developing functional health foods and should be further evaluated in preclinical models.