The application of Carbon and graphite based materials in unprotected environment is limited to a temperature of 450℃ or so because of their susceptibility to oxidation at this temperature and higher. To over come these obstacles a low cost chemical vapour reaction process (CVR) was developed to give crystalline and high purity SiC coating on graphite and isotropic C/C composite. CVR is most effective carbothermal reduction method for conversation of a few micron of carbon layer to SiC. In the CVR method, a sic conversation layer is formed by reaction between carbon and gaseous reagent silicon monoxide at high temperature. Characterization of SiC coating was carried out using SEM. The other properties studied were hardness density and conversion efficiency.

Wear of steel plate was measured during unlubricated sliding against TiC composites. These composites consist of round TiC grains and steel matrix. TiC grain itself exhibits low surface roughness and round shape, which does not bring its counterpart into severe damage from friction. In our work a classical experimental design was applied to find out a dominant factor in counterpart wear. The analysis of the data showed that only the applied load has a significant effect on the counterpart wear. Wear rate of counterpart increased non-linearly with applied load. Amount of wear was discrepant from expectation of being in proportion to the load by analogy with friction force. Our experimental result from treating matrix variously revealed bimodal wear behavior between the composites and counterpart where a mode seems to result from the special lubricant characteristic of TiC grains, and the other is caused by metal-to-metal contact. The two wear mechanisms were discussed.

The experimental data from the central composite design runs were utilized for mathematical models far the drilling characteristics containing linear, quadratic and interactive effects of the parameters such as volume fraction of TiC in the composites, drill speed, feed rate and drill diameter. The models were developed via stepwise selection where the insignificant effects were removed using t-test. The models were subjected to optimization of maximizing drill life and satisfying the other constraints.

Several boride sintered bodies such as , , and were previously reported. In the present study, the sinterability and physical properties of chromium boride containing chromium carbide sintered bodies were investigated in order to determine its new advanced material. The samples were sintered at desired temperature for 1 hour in vacuum under a pressure by hot pressing. The relative density of sintered bodies was measured by Archimedes' method. The relative densities of addition of 0, 5, 10, 15 and 20 mass% composites were 92 to 95%. The Vickers hardness of the with 10 and 15 mass% composites were about 14 and 15 GPa at room temperature, respectively. The Vickers hardness at high temperature of the addition of 10 mass% composite decreased with increasing measurement temperature. The Vickers hardness at 1273 K of the sample was 6 GPa. The Vickers hardness of addition of composites was higher than monolithic sintered body. The powder X-ray diffraction analysis detected CrB and phases in containing composites.

The pretreatment for substrate was carried out in change of gun pressure of bar using wet blasting. The size of powder was about . As the results, the surface roughness of cemented carbide substrate was improved with increment of gun pressure of wet blasting. A new surface layer was formed and Co particles were uniformly distributed over the entire surface after pretreatment. The adhesion of the pretreated substrate in same PVD-TiAlN film was improved and in approximately shown the best adhesion value.

Silicon nitride - silicon carbide composite was developed by using an abrasive SiC powders as a raw material. The composites were prepared by mixing abrasive SiC powder with silicon, pressing and sintering at under nitrogen atmosphere in atmosphere controlled vacuum furnace. The proportion of silicon in the initial mixtures varied from 20 to 50 wt%. After sintering, crystalline phases and microstructure were characterized. All composites consisted of and as the bonding phases in SiC matrix. Their physical and mechanical properties were also determined. It was found that the density of the obtained composites increased with an increase in the content formed in the reaction.

Through the review of developing course of China cemented carbide industry, the writer of this paper at the first time generalizes it into five stages. The writer analyses China cemented carbide industry present status in aspects of produce technology, product structure, operation and management etc. Mean while by analysis of existed shortages in cemented carbide industry, the write considers that it also has three advantages in resource and scale, industry foundation and categories, market and price, and brought out some suggestion and imagination for the future develpment of China cemented carbide industry.

In recent years, PCB drills with smaller diameters less than 0.1 mm are used and thus there are growing needs for ultra-fine grained cemented carbides. However, ultra-fine WC powder usually causes extraordinary grain growth during sintering which weakens mechanical strength of ultra-fine grained cemented carbides. So we examined several kinds of WC powders to make new ultra-fine grained cemented carbides having superior performance. We found that direct carburized WC powder is very good as a WC raw material. The PCB drills made of the developed ultra-fine grained cemented carbides have higher hardness, toughness and stiffness than conventional ones.

Titinium carbide (TiCx) was produced by self-propagating high temperature synthesis (SHS) method. The morphology and non-stoichiometric number of the SHS product were observed by scanning electron microscopy and neutron diffractometry, respectively. Tubular titanium carbide with hole inside was formed with different non-stoichiometric number (x), which value increased with combustion temperature.

Silicon carbide whiskers (SiCw) having the diameter in the range of 20-80 nm were synthesised from coconut fibres through sol-gel process. The coconut fibres were impregnated with tetraethoxysilane and methyltriethoxysilane derived sol and pyrolyzed at 1400℃ in argon. X-ray of the pyrolyzed samples showed the formation of β-SiC.

Development of recycling method at cemented carbide scraps was researched. Some properties of recycled cemented carbides were investigated. Recycled WC fine powder suffered the surface oxidation. Therefore it was necessary to be done by reduction treatment at 1073K-3.6ks under hydrogen atmosphere. When sintering condition at 1673K-3.6ks was treated under vacuum condition, it gained the deflective strength of about 90%, and gained hardness and sintering density about same value compared with commercial alloys. As a result, it was able to recycle only by 7 processes.

This paper introduces a special spheroidizing technology at ultra-high temperature. The conventional cast tungsten carbide (YZ) is melted at high temperature, rapidly cooled and spheroidized on a new ultra-high temperature spheroidizing equipment to prepare various grades WSC powders.

To improve the mechanical properties of WC-Co cemented carbides, the dual composite was studied. The compositions of granule and matrix were nano-sized WC-6 wt% Co(granule) and normal sized WC-20 wt% Co(matrix), respectively. The granules were grouped 50, 100 and and mixed with WC and Co powders as the volume fractions of granule to matrix were 50 to 50, 40 to 60 and 30 to 70. These compacts were sintered at for 10 minutes in vacuum. The microstructure, transverse rupture strength and wear resistance were investigated.

In this paper, we show some experimental results of binder-free WC sintered by Pulsed Electric Current Sintering (PECS) also known as Field Assisted Sintering Technology (FAST). These binder-free WC have extremely hardness and stiffness. However, these mechanical properties are dependent on the sintering condition, e.g., maximum temperature, applied pressure, etc. We show some relationship between mechanical properties and sintering condition to improve to sinter the binder-free WC.

The deformation behavior under three-point bend test was found to depend on the loading uniformity and the macrostructure for SiC reticulated porous ceramics (RPCs). However, this dependence of loading uniformity is alleviated by improved macrostructure with fewer flaws and clogged pores. Even, this dependence becomes less important as the struts become thicker and stronger. The bend result of RPCs with highly uniform macrostructure is in excellent agreement with the GA (Gibson and Ashby) model, but the one with un-uniform macrostructure deviates from the GA model, suggesting that the macrostructure plays an important role in deformation behavior of RPCs under bend.