에너지원으로서 수소를 생산하기 위하여 하니컴 구조를 갖는 모노리스에 10 wt% Ni/CeO2-ZrO2 촉매를 담지한 후 메탄의 수증기 개질 실험을 수행하였다. 다른 CeO2/ZrO2 몰비를 갖는 촉매들 중에서, Ni/CeO2-ZrO2(CeO2/ZrO2=4/1)촉매가 700-800℃에서 높은 메탄의 전환율을 보여 주었다. 10wt% Ni/CeO2-ZrO2 촉매가 담지된 금속 모노리스 촉매체는 높은 열전도도와 비표면적들로 인하여 좋은 촉매 특성을 보여줌을 확인할 수 있었다. 또한, 금속모노리스 촉매체는 반응물에서 과다의 수증기에 의한 수소 수율에서 크게 영향을 받지 않음을 알 수 있었다. GHSV=30,000h-1, 반응물 비(H2O/CH4=3.0) 반응온도 800℃에서 금속모노리스 촉매체는 98%이상의 메탄의 전환율을 보여주었다. 생성물 가스에서 CO2/CO의 비는 수증기/메탄의 반응물비가 증가할수록 수성가스화 반응에 의하여 증가됨을 알 수 있었다.

추출크로마토그래피법과 액체섬광계수법을 이용하여 고체 시료중의 와 방사능을 측정할 수 있는 분석법을 확립하고 연구로 2호기의 해체시 발생되는 방사화된 콘크리트 폐기물을 분석하였다. 침전법과 추출크로마토그래피법으로 화학분리를 하면, 경우 Fe의 화학적 회수율은 대부분의 시료에서 90%이상이었으나 Ni의 회수율은 43.6과 46.5%를 나타낸 시료가 있으며 나머지는 62% 이상을 나타내었다. Spiked 시료를 이용하여 분리과정과 액체섬광계수법의 과정을 확인한 결과 의 경우는 3.7% 오차내의, 의 경우는 0.7% 오차내의 결과가 얻어졌다. 연구로 2호기의 해체 콘크리트 시료중 방사능은 MDA이하의 값도 있으나 TC3시료의 경우는 362Bq/g의 값이 얻어졌다. 그리고 의 경우는 모든 시료에서 MDA이하 값이 얻어져 이 존재하지 않음을 알 수 있었다. 그리고 콘크리트 벽의 해체시 표면의 시료는 의 방사능이 높다가 표면으로부터 깊은 시료일수록 의 방사능이 급격히 줄어들었다.

The present investigation has attemped to optimize hydrogen reduction process for the mass production of Fe-8wt%Ni nanoalloy powder from ball milled powder. In-situ hygrometry study was performed to monitor the reduction behavior in real time through measurement of water vapor outflowing rate. It was found that the reduction process can be optimized by taking into account the apparent influence of water vapor trap in the reactor on reduction kinetics which strongly depends on gas flow rate, reactor volume and reduction.

Tungsten heavy alloys with different ratios of Mo and Ni-Fe matrix were liquid-phase-sintered to investigate their microstructural evolution. Results indicated that increased Mo in the alloy promoted the formation of a (W,Mo)(Ni,Fe) type intermetallic compound in the furnace-cooled condition. It was a monoeutectic reaction when the added Mo content was higher than 49at.%, or a eutectic reaction when this value was between 37at,% to 49at.%. When Mo was added between 25at.% to 37at.%, the precipitation of the intermetallic compound took place by either a eutectoid or peritectoid reaction.

Co-Fe-Ni-B-Si-Cr based amorphous strips containing nitrogen were manufactured via melt spinning, and then devitrified by crystallization treatment at the various annealing temperatures of for up to 30 minutes in an inert gas atmosphere. The microstructures were examined by using XRD and TEM and the magnetic properties were measured by using VSM and B-H meter. Among the alloys, the amorphous ribbons of containing 121 ppm of nitrogen showed relatively high saturation magnetization. The alloy ribbons crystallized at showed that the grain size of alloy containing 121 ppm of nitrogen was about f nm, which exhibited paramagnetic behavior. The formation of nano-grain structure was attributed to the finely dispersed Fe4N particles and the solid-solutionized nitrogen atoms in the matrix. Accordingly, it can be concluded that the nano-grain structure of 5nm in size could reduce the core loss within the normally applied magnetic field of 300A/m at 10kHz.

The effect of use of as PCA(process control agent) to prevent the carbon contamination during mechanical alloying process and the precipitation behavior in Ni-20Cr-20Fe-5Nb bulk alloy after aging were investigated. NbC and were formed during mechanical alloying and consolidation processes in the Ni-20Cr-20Fe-5Nb alloy in which methanol() was added as PCA. Formation of NbC in this alloy decreased the amount of Nb dissolved in the Ni matrix. The use of as PCA in Ni-20Cr-20Fe-5Nb alloy prevented the formation of NbC and increased the hardness. The increase of hardness in this alloy was attributed to the increased amount of Nb dissolved in the Ni matrix. After aging treatment for 20 hours at of Ni-20Cr-20Fe-5Nb bulk alloy in which added as PCA, precipitates were formed, respectively. The precipitation temperatures of and in this bulk alloy were lower than those in commercial IN 718 alloy. It seemed that the lower precipitation temperatures for and in this bulk alloy than in commercial IN 718 alloy were due to severe plastic deformation during mechanical alloying.

The effects of compaction pressure and sintering temperature on the densification of Fe-40wt%Ni alloy nanoparticles were analyzed. The Fe-Ni nanoparticles were fabricated by an arc-discharge method and then, compacted at three different pressures and sintered at 550 to . Densification was completed at temperature as low as and high-pressure compaction was found to enhance densification. Densification behaviors and microstructure developments have been investigated through density measurements, electron microscopies, and hardness measurements.

The present investigation has been performed on full densification behavior and mechanical property of the powder injection molded Fe-8wt%Ni nanoalloy powder. The net shaping process of the nanopowder was conducted by powder injection molding (PIM) process. The key-process for fabricating fully densified net-shaped nanopowder by pressureless sintering is an optimal control of agglomerate size of nanopowder. Enhanced mechanical property of PIMed Fe-Ni nanopowder is explained by grain refinement and microstructural uniformity.

Fe-4Ni-0.5Mo-1Cu powder was selected as raw material, pressed and sinter-hardened at for 30 min with rapid cooling. The density varies in the range of . Its fatigue properties have been tested in axial loading of alternating tensile/compressive stress at R=-1 with a servo-pulse pump. The fatigue endurance limit was measured to be 260 MPa. The microstructure showed more homogeneous bainite and martensite. Fractography displayed the fatigue cracks initiated from the pore areas near the surface. A non-typical ductile fatigue striation was found. More dimples occurred on fracture surface due to the plastic deformation, which can prohibit cracking propagation and improve its fatigue properties.