간행물
한국기계기술학회지 KCI 등재 Journal of the Korean Society of Mechanical Technology 韓國機械技術學會誌
- 발행기관 한국기계기술학회
- 자료유형 학술지
- 간기 격월간
- ISSN 1229-604X (Print)2092-0385 (Online)
- 수록기간 1999 ~ 2024
- 주제분류 공학 > 기계공학 공학 분류의 다른 간행물
- 십진분류KDC 550DDC 620
권호리스트/논문검색
제20권 제6호 (2018년 12월) 33건
학술연구
21.
2018.12
구독 인증기관 무료, 개인회원 유료
Steam tables including superheated, saturated and compressed region were simultaneously modeled using the neural networks. Pressure and temperature were used as two inputs for superheated and compressed region. On the other hand Pressure and dryness fraction were two inputs for saturated region. The outputs were specific volume, specific enthalpy and specific entropy. The neural network model were compared with the linear interpolation model in terms of the percentage relative errors. The criterion of judgement was selected with the percentage relative error of 1%. In conclusion the neural networks showed better results than the interpolation method for all data of superheated and compressed region and specific volume of saturated region, but similar for specific enthalpy and entropy of saturated region.
4,000원
22.
2018.12
구독 인증기관 무료, 개인회원 유료
Precedent research and development of personal armor and anti-stab wearing system has been conducted since 2018 as a part of the government-affiliated cooperative development project to create the best utilization of present technology and achievement according to the civil and military technical cooperation project promotion law. At present, the armor system operated by the ROK(Republic of Korea) military, the police, and the marine police is utilizing only basic armor using armor vests and plates. Therefore it is necessary to develop the personal armor and anti-stab wearing system which is suitable for various tasks in army with maximum protection capability. In this paper, we analyzed the study about international technologies, market trends of the developed countries and scope of research, utilization plan, R&D results for the best armor and anti-stab wearing system development.
4,000원
23.
2018.12
구독 인증기관 무료, 개인회원 유료
In this study, clinching characteristics of aluminum and galvanized steels were investigated for the application of clinching as a joining technique to aluminum wheelhouse assembly. A6451 aluminium alloy and galvanized steel sheets were joined by hybrid joining(clinching + adhesive bonding). Tensile-shear load and fracture mode of hybrid joints were investigated. Maximum tensile-shear load of hybrid joints was about six times higher than that of clinched joints without adhesive. Energy absorption values of hybrid joints were higher than those of clinched joints without adhesive as well as resistance spot welded steel joints. Developed aluminum wheelhouse assembly showed higher static stiffness than the existing steel parts. Aluminum wheelhouse inner panel unit was 44% lighter than the steel unit, and the final assembled aluminum wheelhouse was 14.6% lighter than the existing steel parts.
4,000원
24.
2018.12
구독 인증기관 무료, 개인회원 유료
Among the soft ground improvement methods, PBD is the most common construction method because it is cheap and construction is fast. However, if the ground is rigid, additional work is required. In this study, the structural safety, natural vibration, and safety angle of the steel vertical tower structure were evaluated in the development of the PBD composite perforator which can be combined with drilling work and PBD construction. Structural safety was assessed when the wind load of 20 m/s was simultaneously applied to the PBD construction load of 20 tons, the perforating operation of 25 tons, and the wind speed of 50 m/s was applied only to the wind load. The natural frequencies were evaluated up to the sixth mode, and the safety angle was evaluated for static and dynamic safety angles.
4,000원
생산기술
25.
2018.12
구독 인증기관 무료, 개인회원 유료
The objective of this study is to investigate the effect of torque variation on stress distributions in A-IMS module with both side tubular shaft yoke by numerically. In order to achieve this, the torque value was increased from 10Nm to 40Nm, and the results of this work were confirmed in terms of Von-mises Stress and the displacement characteristics. As the torque in module assembly was increased, the stress in tubular shaft york and splined shaft york was increased linearly. The indentation due to the steel ball was occurred in over 40N·m torque which is over the yield strength condition. The largest displacement occurred in the tubular shaft yoke 1, however, it does not exceed the yield strength and is supposed to be restored due to the elasticity. Therefore, it was concluded that there is no problem for the manufacturing of A-IMS with both side tubular shaft yoke.
4,000원
26.
2018.12
구독 인증기관 무료, 개인회원 유료
This study was conducted to develop an efficient high performance range hood and exhaust system for quickly discharging flue gas, smoke, and odor generated when food is cooked in the kitchen, and the following results were obtained. Reverse current rate of 1.53 m/s of the range exhaust system was improved to achieve the inlet speed of 0.3 m/s or less. An efficient range system was constructed by improving the hood exhaust flow by 5.6 m/s at the existing 4.5 m/s.
4,000원
27.
2018.12
구독 인증기관 무료, 개인회원 유료
Crawling robots are advantageous in overcoming obstacles. These robots have characteristics such as light weight and outstanding mobility. In case of large robots, they have difficulties passing narrow gaps or entering the cave. In this paper, we propose a milli-scale hexapedal robot using 4-bar linkages. Two conditions are necessary to enable efficient walking. In short, the trajectory of the foot must be elliptical, and the lowest point of the foot should be the same. These conditions are satisfied with a novel leg design. The robot has a pair of three legs and the legs are coupled to operate simultaneously. Each set of the legs are installed to robot’s both sides and the legs satisfy the equal lowest foot point and elliptical trajectory. As a result, this hexapedal robot can crawl with 0.56m/s speed.
4,000원
28.
2018.12
구독 인증기관 무료, 개인회원 유료
The drinking water supply system applicable to the laying hen consists of air-water heat pumps, drinking water tanks, heat stroage tank, circulation pumps, PE pipes, nipples, and control panels. When the heat pump system has power of 7.7 to 8.7 kW per hour, the performance coefficient is between 3.1 and 3.5. The supply temperature from the heat pump to the heat stroage tank was stabilized at about 12±1°C, but the return temperature showed a variation of from 8 to 14°C. Stratified temperature in the storage tank appeared at 12.°C, 13.5°C and 14.4°C, respectively. The drinking water supply temperature remained set at 15°C and 25°C, and the conventional tap water showed a variation for 23°C to 30°C. As chickens grow older, the amount of food intake and drinking water increased. y = -0.0563x2 + 4.7383x + 8.743, R2 = 0.98 and the feed intake showed y = -0.1013x2 + 8.5611x. In the future, further studies will need to figure out the cooling effect on heat stress of livestock.
4,000원
29.
2018.12
구독 인증기관 무료, 개인회원 유료
The objective of this study is to solve a problem that is occurred during the spline machining of tubular shaft yoke in both side IMS module. In order to simulate the problem, the movement direction of upper die was set as standard case and error case. The material of tubular shaft yoke was set to S20C as refer to the analysis library. The movement directions of upper die were separated with standard case and error case. The error case was set to simulate the problem in the spline machining of tubular shaft yoke. In order to solve the problem, the outer radius of upper die were modelled from 9.40mm to 9.44mm. The simulation results were analyzed and compared in terms of effective stress, metal flow line and folding phenomena characteristics. In case of the outer radius of upper die was 9.42mm, it was observed a relatively uniform effective stress distribution and had a straight metal flow line.
4,000원
30.
2018.12
구독 인증기관 무료, 개인회원 유료
This paper develops a flow control block for a hydraulic system of a tunnel boring machine. The flow control block is a necessary component to ensure stability in the operation of the hydraulic system. In order to know the pressure distribution of the flow control block, the flow analysis was performed using the ANSYS-CFX. It was confirmed that the pressure and flow rate were normally supplied to the hydraulic system even if one of the four ports of the flow control block was not operated. In order to evaluate the structural stability of the flow control block, structural analysis was performed using the ANSYS WORKBENCH. As a result, the safety factor of the flow control block is 1.54 and the structural stability is secured.
4,000원
31.
2018.12
구독 인증기관 무료, 개인회원 유료
Wasted meat & bone has generated as byproducts in the slaughtering process of livestock and also faced with demands for its recycling and environmental protection. Many studies have been conducted to recycle byproducts and carried out mainly on the crushing of bones and the vacuum packing technology of products. In this study, the crushing unit, transporting unit, separated unit and packing unit have designed for development of the crushing and packing systems. Also, to confirm the performance of this system, the experimental verification were carried out the working noise and packing weight.
4,000원
32.
2018.12
구독 인증기관 무료, 개인회원 유료
Currently, due to the development of technology, the industry is proceeding with the development of advanced materials with high performance such as light weight, heat resistance and electric conductivity. Carbon Fiber Reinforced Plastics (CFRP) is an excellent material with high heat resistance, high strength and thermal shock resistance. In order to obtain excellent hole shape in CFRP drilling, we compared the modified drill shape and the conventional carbide drill. On the other hand, we determine the proper helix angle by observing the CFRP surface according to the helix angle at the trimming of the end mill proceeding after the hole machining.
4,000원
33.
2018.12
구독 인증기관 무료, 개인회원 유료
This research has been conducted to design upright parts of hand-made vehicles with the purpose of reducing material and machining cost while ensuring structural safety. Aluminum knuckles were modelled with three parts in order to enhance design flexibility as well as to reduce CNC machining cost. A vehicle model was constructed in CAD program and simulated in ADAMS View in order to estimate joint forces developing during 20 degree step steering condition at 60km/h. The joint forces obtained in the vehicle dynamics simulation were used for the structural analysis in ANSYS and dimensions of knuckle parts were adjusted until the lowest safety factor reached 2.0. The weight of knuckle decreased by 50% compared to the previous version that was designed without the structural analysis. The overall manufacturing cost decreased by 33% due to the reduction in the material as well as the CNC machining effort.
4,000원
1
2
