In order to improve the thermal stability of PAN-based electrospun fibers, AP-PER-MEL and TiO2 were added in to the fibers as additives. The polymer composite with uniformly mixed additional agents was obtained. In case of non-treated sample, the fibers were burn off completely with high rate within 620℃. But in case of treated samples (EF-M and EF-MT), it is sure that the thermal stability was improved by studying TGA data and ISO flammability test about 20 and 30%, respectively. A synergy effect of adding two kinds of agents (AP-PER-MEL and TiO2) into PAN-based electrospun fibers was confirmed. Through SEM images, it is confirmed that the fiber shape can be kept even after addition of agents (AP-PER-MEL and TiO2). Finally the thermal stability of fibers was largely developed with keeping the nature of PAN-based fibers effectively.

사용후핵연료 심지층처분에 있어서 처분용기의 건전성 확보는 내부에 적재되어 있는 사용후 핵연료로부터 방사성물질이 누출되는 것을 방지하고 격리하여 처분장의 안전성을 보증하기 위한 필수적인 인자이다. 이러한 처분용기는 심지층 처분의 목적인 방사성 독성이 인간 및 자연환경에 영향을 미치지 않도록 장기간 동안 격리하고 누출을 지연시키기 위한 공학적 방벽의 중요한 요소 중의 하나이다. 심지층 처분장 설계시 주요한 요건은 처분시스템의 안전성을 유지를 위하여 처분용기에 적재되어 있는 폐기물로부터 발생된 붕괴열로 인하여 완충재의 온도가 100를 넘지 않도록 하는 것이다. 또한, 처분용기는 지하 심부 500 m 깊이에서의 수압과 완충재의 팽윤압 등 하중에 구조적 건전성을 유지하여야 한다. 본 연구에서는 직접 처분대상으로 고려하고 있는 중수로(CANDU) 사용후핵연료에 대한 처분용기의 개선된 개념을 설정하고, 심지층 처분환경에서의 열적 및 구조적 안정성을 분석하였다. 열적 안정성 해석결과 처분터널 및 처분공 간격이 40 m, 3 m 인 경우 처분 후 37년이 경과한 후에 처분용기 표면온도가 최고 온도에 도달하며, 이때 온도는 88.9 로서 처분장 온도제한 요건(100 )에 만족하였다. 또한, 정상적인 경우와 극한 상황에 따른 하중에 대한 처분용기 구조해석 결과 안전율은 각각 2.9와 1.33 으로 나타나 심지층 처분환경에서 처분용기는 구조적 건정성을 유지하는 것으로 판단되었다.

This paper describes the experiments for investigating the effects of thermal stability of several commercial carpet mate materials. The melting point and thermal decomposition temperature was measured by means of a differential scanning calorimeter(DSC) in air condition. The DSC data and burning test results of nylon bulked continuous filament(N-BCF) yarn 100%, nylon(NY), polypropylene(PP), and a new material named polytrimethyleneterephthalate(PTT) were analysed to obtain the effect on their thermal stability. Conclusively, we observed that PTT and PP were approximately 380℃ and 240℃ to start the thermal decomposition, respectively. In other words, PTT is thermally the most stable material for carpet manufacturing.

Cu- nanocomposite powders were synthesized by combining high-energy ball-milling of Cu-Ti-B mixtures and subsequent self-propagating high temperature synthesis (SHS). Cu-40wt.% powders were produced by SHS reaction and ball-milled. The milled SHS powder was mixed with Cu powders by ball milling to produce Cu-2.5wt.% composites. particles less than 250nm were formed in the copper matrix after SHS-reaction. The releative density, electrical conductivity and hardness of specimens sintered at were nearly 98%, 83%IACS and 71HRB, respectively. After heat treatment at 850 to for 2 hours under Ar atmosphere, hardness was descedned by 15%. Our Cu- composite showed good thermal stability at eleveated temperature.

The preparation of metallic glass composite powders was accomplished by the mechanical alloying of a pure Ti, Cu, Ni, Sn and carbon nanotube (CNT) powder mixture after 8 h milling. In the ball-milled composites, the initial CNT particles were dissolved in the Ti-based alloy glassy matrix. The bulk metallic glass composite was successfully prepared by vacuum hot pressing the as-milled CNT/ metallic glass composite powders. A significant hardness increase with the CNT additions was observed for the consolidated composite compacts.

Ti-Cu-Ni-Sn quaternary amorphous alloys of Ti50Cu32Ni15Sn3, Ti50Cu25Ni20Sn5, and Ti50Cu23Ni20Sn7 composition were prepared by mechanical alloying in a planetary high-energy ball-mill (AGO-2). The amorphization of all three alloys was found to set in after milling at 300rpm speed for 2h. A complete amorphization was observed for Ti50Cu32Ni15Sn3 and Ti50Cu25Ni20Sn5 after 30h and 20h of milling, respectively. Differential scanning calorimetry analyses revealed that the thermal stability increased in the order of Ti50Cu32Ni15Sn3, Ti50Cu25Ni20Sn5, and Ti50Cu23Ni20Sn7.

The accidents occurred by unstable material which is easily exploded or burnt up were caused by heat and collision under the condition of relatively low temperature without oxygen, have been reported frequently. However, the amount of the unstable material is getting higher by development of fine ceramic research area even though its dangerous characteristic is disregarded. This research studied a heat stability and measured boiling point of various carpet material. Carpet has been used in home as well as general indoor usage. Now a day, carpet material which is hardly burnt has been on commercial, but its detailed unstable conditions is not mentioned. This research reports the measurement of the initial temperature of generation heat and heat-radiation change on differential scanning calorimeter (DSC). The DSC data of nylon bulked continuous filament (N-BCF) yam 100%, nylon (NY), poly propylene (PP), and a new material named polytrimethylene terephthalate (PTT) are studied and researched about the effect of them using TGA, furnace, and direct-burning experiment.

Mechanical alloying using high-energy ball mill and subsequent spark plasma sintering (SPS) process was applied to understand mechanical alloying processing of Al-Fe alloy system. The thermal stability of mechanically alloyed Al-Fe alloy was intended to be enhanced by SPS process. Various analytical techniques including particle size analysis, density measurement, micro-Vickers hardness test, SEM, TEM, and X-ray diffractometry were adopted to find optimum processing conditions for mechanical alloying and subsequent SPS and to estimate thermal stability of the prepared alloy. It was found from the treatment of mechanically alloyed Al-8wt.%Fe powder mixture that needle-shaped precipitates was formed in the Al-Fe matrix, and the alloy compact showed enhanced densification and reached its full density with little loss of its fine microstructure. After heat treatment at , it was also shown that the thermal stability of Al-8wt.%Fe alloy fabricated in the present study was enhanced, which was due to its fine microstructure developed by fast densification of SPS.

Mechanical alloying using high-energy ball mill and subsequent spark plasma sintering (SPS) process was applied to Al-Fe-Cr and Al-Fe-Mo powder mixture to investigate effects of Cr and Mo addition on thermal stability of Al-Fe, and thereby to enhance its thermal stability up to . Various analytical techniques including micro-Vickers hardness test, SEM, TEM, X-ray diffractometry and corrosion test were carried out. It was found that addition of Cr and Mo to Al-Fe system played a role of grain growth inhibitor of matrix Al and some precipitates such as during SPS and subsequent heat treatment. The inhibition of grain growth resulted in increased Vickers hardness and thermal stability up to comparing to those of Al-Fe alloy system.

Sodium azide (SA) is commonly used as propellant for inflating automatic safety bags and other chemical manufacturing purposes. The investigation of potentially thermal hazard of sodium azide and its mixture with polymers are very important because it can occur an expected traffic accident so we took a experiment s using different scanning calorimeter (DSC) in nitrogen atmosphere. The decomposition temperature were about 350~450℃. We could find not only exothermic reaction was remarkably decreased in mixture s of acrylonitrile-butadiene-styrene (ABS) and polyvinyl chloride (PVC), but also increasing mixed rate of ABS, polyvinyl alcohol (PVA) and polymethyl methacrylate (PMMA) decreased thermal decomposition heat.