간행물
한국기계기술학회지 KCI 등재 Journal of the Korean Society of Mechanical Technology 韓國機械技術學會誌
- 발행기관 한국기계기술학회
- 자료유형 학술지
- 간기 격월간
- ISSN 1229-604X (Print)2092-0385 (Online)
- 수록기간 1999 ~ 2025
- 주제분류 공학 > 기계공학 공학 분류의 다른 간행물
- 십진분류KDC 550DDC 620
권호리스트/논문검색
제26권 제4호 (2024년 8월) 28건
21.
2024.08
구독 인증기관 무료, 개인회원 유료
In this study, the operating performance of the heat pump dryer using the PF heat exchanger was experimentally studied. The capacity, COP, drain, SMER and operating status of the cooling cycle of the heat pump dryer were investigated according to the temperature, relative humidity and flow rate of the indoor air. Heat pump dryers are refrigerant-air system. For the dryer performance experiment, an air enthalpy calorimeter was used. From the experimental results, as the temperature, relative humidity, and flow rate of the inlet air increased, the capacity, COP, drain, SMER of the dryer increased. The change in the performance of the dryer was most affected by temperature. The P-h diagram of the cooling system showed that the operation status of the dryer was greatly affected by the indoor temperature. In addition, the SMER of the dryer showed a drying performance of about 3.38 kg/kWh or more within all experimental ranges.
4,000원
22.
2024.08
구독 인증기관 무료, 개인회원 유료
The main hydraulic pump is a device that generates the hydraulic pressure needed for the K2 tank. It is a pressure-compensated swash plate piston pump that generates the hydraulic power necessary to drive the hydraulic device. Hydraulic pump design changes were made due to frequent failures of the hydraulic pump. As a result of checking the operation records of the hydraulic pump, about 71% of the total engine operation time was in a stationary state where hydraulic pressure was not needed. This has the problem of constantly running when the engine is started, consuming unnecessary endurance time, and generating high noise. In this study, ISG(Idle Stop & Go) was applied to improve operation method. When applying ISG, the pressure can be reduced to about 85% or less in an environment where the operation of the main hydraulic pump is not necessary. So, the lifespan of the main hydraulic pump increases as a result of ISG application, thereby reducing the waste of national funds due to maintenance costs. Also, it is expected to contribute to improving combat power by reducing crew fatigue due to noise reduction.
4,000원
23.
2024.08
구독 인증기관 무료, 개인회원 유료
In this paper, the goal is to produce a target wheel that integrates the plate and CPS wheel among the components of the drive plate mounted on an automobile engine. We attempted to develop a manufacturing process technology for incremental forming of a target wheel with the desired thickness by rotating a disk-shaped thin plate material and deforming the plate using a forming device and tools. Incremental forming system was set up by establishing a forming process and designing and manufacturing the device and parts required for processing. It consists of a total of 4 stages of molding process, and the optimal roll design that can properly collect materials to prevent cracks or reverse steps at each stage is primarily important. After manufacturing the prototype, a material test was performed to confirm whether the mechanical properties of the deformed part were sufficient to make gear teeth.
4,000원
24.
2024.08
구독 인증기관 무료, 개인회원 유료
This study is to deal with a failure phenomenon that occurred during a vibration test on an Inertial Navigation System mounted on a self-propelled howitzer. Vibration occurs naturally due to the operation characteristics of self-propelled howitzers, The study describes a case of failure that occurred during the durability verification process. It explains the function and configuration of the INS(Inertial Navigation System) and describe how the failure occurred through understanding the phenomenon. Based on the occurrence phenomenon, an in-depth cause analysis was conducted and fundamental improvement measures were presented to prevent recurrence. It is expected that this study will aid as a reference for problem solving when similar failures occur in the future.
4,000원
25.
2024.08
구독 인증기관 무료, 개인회원 유료
This paper aims to introduce a case of improving the performance of aged naval ships' Identification Friend or Foe(IFF) equipment from Mode 4 to Mode 5, thereby enhancing operational capabilities and overcoming integration limitations. Since 2019, South Korea has been conducting a project to replace IFF equipment across the entire military, categorized into naval ship, air force aircraft, surveillance and reconnaissance, and protection. Among these, three naval classes without combat systems required not only an upgrade of their IFF equipment from Mode 4 to Mode 5 but also an integration capability that would allow them to maintain the same fire control procedures by linking with existing naval gun fire control systems. To implement this integration function, the signal processing methods of the existing IFF equipment were analyzed, and based on this, the integration function was implemented in a signal converter module. This paper is expected to serve as an important resource for future performance upgrades of internal equipment in aged naval ships.
4,000원
26.
2024.08
구독 인증기관 무료, 개인회원 유료
In this article, improvement of heat screen failure for battle tank is proposed. The heat screen applied to protect a cam sensor from engine heat was cracked by vibrations generated in the engine. To solve this problem, the configuration of the heat screen was changed to a structure that can avoid engine vibration levels. The improved heat screen has first mode frequency at 4,000 RPM band outside the main operating range of the engine, and heat dissipation is at the same level as conventional heat screen. As a result, the improved heat screen secured reliability by improving vibration effects by approximately 163% while maintaining heat dissipation performance.
4,000원
27.
2024.08
구독 인증기관 무료, 개인회원 유료
The condensation phenomenon can affect the product in terms of function and aesthetics, so it is a complaint of many users from the past, and continuous research has been conducted to solve it. A portable instrument panel is installed inside combat vehicles such as tanks and armored vehicles. Due to the nature of the combat vehicle operated in the special situation of battle, the internal heat generation of the instrument panel has increased significantly, which is presumed to be the cause of condensation inside the instrument panel. In this paper, a study on the development of subsequent processes was conducted to reduce the condensation phenomenon of the instrument panel for combat vehicles. In order to reduce the condensation phenomenon, the experiment was carried out by setting baking time and stabilization time as major factors. This paper is considered to be a reference research data for all systems in which similar assemblies are used as well as instrument panels for combat vehicles.
4,000원
28.
2024.08
구독 인증기관 무료, 개인회원 유료
This study identifies the possibility of alignment discrepancies during mortar firing when using inactive fuzes, which make it impossible to visually observe impact points. To address this issue, we studied a quality assurance method for Sight Alignment after firing. To establish a baseline, we analyzed the pre-firing Sight Alignment and the impact group status during firing for 00 mortars and 000 shells. Based on this analysis, we derived the alignment position information range after firing for 36 mortars, distinguishing between 68% and 95% confidence interval. Finally, considering data characteristics, inspection time requirements, and non-conforming data, we selected the Sight Alignment range after firing based on the 95% confidence interval. This study is expected to contribute to the development of quality assurance methods for munitions by serving as an example of quality assurance in the mass production stage of mortars.
4,000원
1
2
