간행물
한국기계기술학회지 KCI 등재 Journal of the Korean Society of Mechanical Technology 韓國機械技術學會誌
- 발행기관 한국기계기술학회
- 자료유형 학술지
- 간기 격월간
- ISSN 1229-604X (Print)2092-0385 (Online)
- 수록기간 1999 ~ 2025
- 주제분류 공학 > 기계공학 공학 분류의 다른 간행물
- 십진분류KDC 550DDC 620
권호리스트/논문검색
제17권 제3호 (2015년 6월) 28건
학술연구
21.
2015.06
구독 인증기관 무료, 개인회원 유료
A deformation of tire structure cause characteristic change of tire as stiffness, ground surface shape, vibration and noise. As a result it will affect "riding quality" factors such as noise and vibration. In this study, figured it out the difference of tire pass by-noise according to ground pressure and stiffness change, to investigate the influence of tire characteristic for tire pass-by-noise. Therefore, The tire ground stiffness and tire pass-by-noise was measured according to pass-by-noise test method(ECE R117). Conclusively, “The tire pass by noise” was confirmed that between vibration and tread shoulder are a close relationship. As the tire shoulder vibration is low, “The acceleration pass-by-noise” can be seen that displayed lower value. In order to distribute contact pressure low for reduce the acceleration pass-by-noise, it could be confirmed that the shoulder stiffness should be greater.
4,000원
22.
2015.06
구독 인증기관 무료, 개인회원 유료
This study was performed to investigate the effect of fuel combustion enhancing apparatus(FCEA) for ionization of intaking air into cylinder combustion chamber on the combustion performance and emissions characteristics in a 4-cylinder common-rail direct injection diesel engine. The experiments were applied to the engine at an engine speed of 1,500rpm under 20Nm, 40Nm, 60Nm and 80Nm conditions. The test results were compared to each other with or without the FCEA. In the case of the FCEA, the combustion pressure, peak combustion pressure and rate of heat release were increased slightly and the brake specific fuel consumption(BSFC) was decreased slightly when compared to that without the FCEA under all loads at an engine speed of 1,500rpm. However, in the case of the FCEA, the nitrogen oxide(NOx) were increased slightly, the carbon monoxide(CO) and particulate matter(PM) were decreased slightly when compared to that without the FCEA under all loads at an engine speed of 1,500rpm.
4,000원
23.
2015.06
구독 인증기관 무료, 개인회원 유료
CFD(Computational Fluid Dynamics) analysis was carried out to analysis the air flow characteristics of vertical axis wind turbine system with accelerating device. Geometric arc angle of the accelerating device affects the air flow characteristics in the turbine with the effect of Coanda generated from the curved surface. Air velocity distributions with the device angle variation are compared. Flow velocity increases with the device length, and the accelerating device plays a key role in decreasing the air velocity in the wake flow region. Maximum air velocity variation becomes reduced with the accelerating device, and it is largely affected by the arc angle. These results are expected to be utilized in various ways to determine the shape of accelerating device for wind power generation system.
4,000원
24.
2015.06
구독 인증기관 무료, 개인회원 유료
In this paper we describe differential circuit of charge pump for voltage management systems, their evolution and improvement in design. The systems are powered by solar cells and generate different voltage levels which are suitable for systems on-chip integrated regulator applications. The voltage regulator outputs voltage from low power digital circuit, -2V for memory, and from 2V to 12V for input and output components. The circuits were simulated using LT SPICE software.
3,000원
25.
2015.06
구독 인증기관 무료, 개인회원 유료
The many parts in the hydraulic equipments subject to load by hydraulic pressure. And some parts which are installed to the inside of the hydraulic equipments subject to load by the hydraulic pressure as well as the fluid speed. The inside of the valve generally generates the flow. Considering the valve expansion or the flow of the large valve, the flow is similar to the fluctuation flow in the opened flow system. In this study, the analysis of the flow including the fluctuation are performed and this results will apply to the optimal shape design of the flow path. The load acting on the structure was analysed according to the change in the shape and flow speed of the structure which install in fluid, and the safety evaluation wad investigated in consideration of the flow speed and the depth of fluid.
4,000원
생산기술
26.
2015.06
구독 인증기관 무료, 개인회원 유료
In general, it is required mechanical properties and strength tests to use the material in engineering applications. The material fringe values of photoelastic materials vary with the supplier, the batch of resin, temperature and age, it is necessary to calibrate each of sheet of photoelastic material at the time of the test. In this paper, we perform tensile tests and calibrations tests for photoelastic stress fringe constant in order to obtain the mechanical properties of materials and photoelastic material fringe constants of PMMA and PSM-1. From this tests, the tensile strength of PMMA and PSM-1 were 100.5 MPa and 71.5 MPa, respectively. Also, the measured material stress fringe constants of PMMA and PSM-1 were 13.33 N/mm and 6.91 N/mm, respectively.
4,000원
27.
2015.06
구독 인증기관 무료, 개인회원 유료
Multi-layered metal sheet for electromagnetic interference(EMI) shielding purpose has been designed using metal sheet, PET & DST stacking and laminating technology. Also, an automatic manufacturing system is developed. This metal sheet with multi-layered structure is an effective shield against EMI that can not shield completely by single metal sheet. And the developed automatic manufacturing system can stack and lamination thin metal sheets without any wrinkles.
4,000원
28.
2015.06
구독 인증기관 무료, 개인회원 유료
The functional wood plastic composite(WPC) is one of the noted materials for landscape architecture and residential construction. Iron band, embossing and drain holes are improve the strength and skid resistance of the WPC. In this study, we had developed an automatic manufacturing system for the functional WPC that has vertical pattern embossing and drain holes. The system is consist of an automatic vertical pattern embossing device, multi-spindle drilling M/C, sanding device, inspection equipment, and some facilities developed in the previous research. The performance tests on the several functional items of the system and manufactured WPC represented satisfactory values except the skid resistance and absorption thickness expansion rate.
4,000원
1
2
