간행물
한국기계기술학회지 KCI 등재 Journal of the Korean Society of Mechanical Technology 韓國機械技術學會誌
- 발행기관 한국기계기술학회
- 자료유형 학술지
- 간기 격월간
- ISSN 1229-604X (Print)2092-0385 (Online)
- 수록기간 1999 ~ 2024
- 주제분류 공학 > 기계공학 공학 분류의 다른 간행물
- 십진분류KDC 550DDC 620
권호리스트/논문검색
제21권 제5호 (2019년 10월) 29건
<학술연구>
21.
2019.10
구독 인증기관 무료, 개인회원 유료
In this study, the structural stability of an align unit was studied to investigate the deformation and vibration characteristics of the upper and lower modules of the align unit during LCD panel transfer. The align unit consists of upper module and lower module. SolidWorks Simulation was used to analyze the structure, fatigue, and modes, to understand the deformation and vibration of the stiffness of the align unit. Because of the upper eccentric structure of the align unit, the main strain was large at the contact of the upper and lower modules and at the bottom of the support, and more pronounced at it’s front. The stress was large in the front support of the upper and lower modules, and the displacement was observed in the front of the upper module. The minimum life cycle that indicates the structural integrity of the align unit has exceeded its usable number. Also, the increase in natural frequency of the align unit gradually slowed down, as the vibration mode increased.
4,000원
<생산기술>
22.
2019.10
구독 인증기관 무료, 개인회원 유료
This study is carried out on the structural improvement of military mobile kitchen trailer for the betterment of fighting power by serving meals to solider in right time. To recognize the real problems of field kitchen trailer, the heat transfers from burner for soup cooker were compared with each other. By the test, the necessity of improvement was deduced. To examine the cause of cooking time, it was determined by the characteristic diagram. Based on the cause, there are two types of kitchen trailer's burner structures. To verify the improved structures, it was carried out for the performance test. As the results, the time did not become longer and the temperature rising rate per minute increased. This study is expected to be devoted to the future improvement of military mobile kitchen trailer.
4,000원
<학술연구>
23.
2019.10
구독 인증기관 무료, 개인회원 유료
The results of internal temperature. productivity and immunity analysis of the laying hen house by the thermal environment and the supply of cold drinking water were as follows. The external temperature was changed from the minimum of 18℃ at night and the maximum of 36℃ during the day, and the internal temperature of the laying hens varied from 20~31℃. Thermal imaging analysis showed that the body temperature of the laying hen decreased by 2.4℃ with the supply of drinking water. The laying hen amount increased 2.36g and laying hen rate increased 3.62%p. Albumin increased 6.1%, decreased AST 15%, and decreased cholesterol 12.7%. Immune activators increased and T cells and B cells increased to increase immunity.
4,000원
24.
2019.10
구독 인증기관 무료, 개인회원 유료
A retractable bollard system has been used for the traffic control and protection of important facilities such as electric power plants, airports and government buildings etc. The power source of the driving unit of the conventional protective bollard system is on hydraulic or pneumatic system which has several disadvantages compared to an electric driven unit.
In this research, an electric driven unit for an automatic retractable bollard is designed and developed to replace the conventional hydraulic and pneumatic driven type. For the reliability test of the developed electric driven unit, a field test has been successfully done.
A case study was conducted to develop a defensive retractive bollard which the target performance is 9sec. and 7sec. on its raising and descending operation speed respectively with 750mm in stroke. The required time limit was fully satisfied as the time measured from the experiment were 7.5sec and 5.5sec for each operation. The developed unit also passed 364,000 cycles of operation without any serious malfunctions at the load test proving its reliability.
The design theory and process of an electric driven unit of the automatic retractable bollard presented in this article is believed to be very useful contribution and design tool in advancing the physical security industry.
4,000원
<생산기술>
25.
2019.10
구독 인증기관 무료, 개인회원 유료
The purpose of this study is to develop and apply an oil leak detector using a capacitive sensor to detect oil leak in hydraulic equipment. The developed oil leak detector consists of a sensor and a sensing circuit. The sensor is designed using the difference in the permittivity of air and oil to change the capacitance, and the sensing circuit is composed of a charge amplifier and rectifier circuit. The sensing device is made of a PCB module to output the DC analog signal. In this study, this oil detector was installed in a cyclic pressure tester for evaluating valve life and was applied to detect the leakage of the test valve. It can also be applied to detecting the oil leakage of various hydraulic types of equipment and reduce maintenance costs by preventing large leakage of hydraulic oil.
4,000원
26.
2019.10
구독 인증기관 무료, 개인회원 유료
In case of worm reducer, the worm and worm wheel are the significant design elements. Most of the worm and worm wheel are being importer and assembled because that the localization is inadequate. As the demand increases and the necessity of localization and precision grows, to develop them is now more important things.
In this study, we conducted the design, manufactured prototype and performance evaluation for worm reducer for dual lead 5.2:1 servo motor. The worm reducer is analyzed design reliability by finite element method. The performance evaluation for manufactured prototype worm reducer was conducted on the backlash, operation temperature and contact efficiency with/without load and satisfied for the all test items.
4,000원
27.
2019.10
구독 인증기관 무료, 개인회원 유료
This study has described as a way of establishing an automated system that allows sorting of living fish caught at sea by weight, and producing and testing as prototypes. The live fish that applied for this research is named as a croaker. 30(thirty) times of measurements with the fishes were applied for screening initially. As a results, it was the highest deviation rate of 19.7% within 2g of their initial weight. In addition, it showed the lowest deviation rate of 8.2% below 10g of them. Throughout the measuring experiments, it was found that the error that occurred during weighting was friction with the upper surface of the load cell on the circular sorting plate. Once the friction was removed, it was figured out that the average deviation in weight per each fish was measured as 0.76g. This error should be able to be eliminated by improving the material of machine elements, the surface material of the load cell. Under this circumstance, this pilot test in sorting living fishes by weight was brought adequate results. The existing sorting device was performed at 4,500 fishes per hour as a sorting speed. The sorting device developed in this research improved productivity by over 33% by setting the sorting speed in 6,000 fishes per hour.
4,000원
28.
2019.10
구독 인증기관 무료, 개인회원 유료
The development of this technology produced the design of welding mesh automation system and obtained the following results.
1. The performance criteria of this research and development were higher than this, resulting in more than 300 N/㎟ of disconnection and more than 250N/㎟ of double wire. Double wire also obtained values of as low as 521 N/㎟ and as high as 623 N/㎟
2. We compared the bending strength of the single mesh and the dual mesh by the bending test, and the result is 1692N of the average of single-mesh and 487N of double wire welded mesh.
3. As a result of the test, 64 minutes of abs of 5mm wire were 112 minutes of each. The welding speed was constant and stable.
4,000원
29.
2019.10
구독 인증기관 무료, 개인회원 유료
Aluminum High Vacuum Die-casting process has become more prevalent in automotive manufacturing industry which require high productive rate, weldable process and heat treatment process. However, high pressure die castings usually contain gas porosity due mainly to the entrapment of air or gas in the die during the high speed injection of the molten metal into the die cavity.
Vacuum block system with disk spring was developed and vacuum chanel was optimized with numerical flow analysis. The porosity of die castings was analyzed by X-ray CT, and the effect of porosity on the mechanical properties was analyzed by hardness and tensile test. Tensile strength was improved 49.5% for 50mbar high vacuum die-casting process compare then 300mbar. And then, Surface property was analyzed with plunger velocity and fast shot set point.
4,000원
1
2
