간행물
한국기계기술학회지 KCI 등재 Journal of the Korean Society of Mechanical Technology 韓國機械技術學會誌
- 발행기관 한국기계기술학회
- 자료유형 학술지
- 간기 격월간
- ISSN 1229-604X (Print)2092-0385 (Online)
- 수록기간 1999 ~ 2024
- 주제분류 공학 > 기계공학 공학 분류의 다른 간행물
- 십진분류KDC 550DDC 620
권호리스트/논문검색
제24권 제6호 (2022년 12월) 51건
21.
2022.12
구독 인증기관 무료, 개인회원 유료
In this study, to improve the performance of kitchen range hoods, a comparative analysis of air volume and noise is conducted using three ducts by changing shapes. It was found that the difference in air volume was caused by the pressure difference received by each shape. The noise data can be found to be no more than 60dB overall, except for the second tier of A-type. The difference when connecting the circular, square, and flexible ducts was judged to be due to some laboratory noise, and it was found that there was no difference.
4,000원
22.
2022.12
구독 인증기관 무료, 개인회원 유료
In this study, We designated the injection molded plug housing for charging electric vehicles as a research subject. And we analyzed the effect of Rib design on the quality of injection molded products. First, we used the Taguchi method to derive optimal conditions for rib design. The factors were set as the Thickness of the rib, the Height of the rib, and the Radius of the rib. Each factor consisted of 5 levels and generated conditions for a total of 125. We performed an injection molding analysis and confirmed significant factors affecting the deformation of injection molded products through ANOVA. Based on this, the 25th design detail was selected as the optimal condition. In addition, We compared the results of the molding analysis with the molded products that did not design ribs. We confirmed that the molded product designed with ribs under optimal design detail improved the deformation amount by 22.22% and the residual stress by 8.35%, compared to the molded product not designed with ribs.
4,000원
23.
2022.12
구독 인증기관 무료, 개인회원 유료
There is a considerable amount of research on metal material product worker’s hearing loss caused by noise that comes from manufacturing process. A further investigation that characterizes the sound that comes from manufacturing process of metal material products. however. To do this, a noise management plan is needed. It should include a generated sound process from the main sources of disturbance at manufacturing process areas. And a soundproof measurement will identify the amount of noise reduction needed for a hearing-safe working environment. Finally, researchers in this study measured tests on the noise and the vibration process, and the noise caused by operations allowed for an investigation on the suitability of certain environmental conditions. Noise-related programs can be used to predict the noise distribution of the noise level characteristic. This can help identify and reduce the presence of sound interference through sound proofing measures.
4,000원
24.
2022.12
구독 인증기관 무료, 개인회원 유료
Thin-film shape technology is recognized for its core technology to enhance the technology of LCD, PDP, semiconductor manufacturing processes, hard disks and optical disks, and is widely used to form coated thin films of products. In addition, resistance (electron beam filament) technology for heating is used to manufacture filament for ion implants used in semiconductor manufacturing processes. By establishing an electronic beam filament production system and developing seven specifications of electronic beam filament, it is contributing to improving trade dynamics and increasing exports to Japan through localized media of theoretical imports to domestic companies. In this study, CAE analysis was performed after setting electron beam filament specification and development objectives, facilities and fabrication for electron beam filament production, electron beam filament JIG & fixture design and fabrication followed by electron beam filament prototype. Then, the automation and complete inspection equipment of the previously developed electronic beam filament manufacturing facilities was developed and researched to mass-produce them, to analyze and modify prototypes, design and manufacture automation facilities, and finally, to design and manufacture the complete inspection equipment. In this paper, mainly design and manufacturing of facilities for making electron beam filament were dealted with.
4,000원
25.
2022.12
구독 인증기관 무료, 개인회원 유료
In this paper, the effect of a dynamic vibration absorber to suppress the response of a base excitation vibration system composed of a cubic nonlinear spring and a friction damper is investigated. And the dynamic absorber consists of a linear spring and a viscose damper. The mathematical models of these systems are governed by second order nonlinear ordinary differential equations. The response characteristics of the system are analyzed using the slowly changing phase and amplitude(SCPA) method, which is one of the averaging methods. As a function of the friction force ratio, It was obtained the locking frequency at which the relative motion starts was obtained, and the regions where the locking occurred. The displacement transmissibility was investigated according to the change of the design parameter, and the optimal design parameters could be found to minimize the displacement transmissibility.
4,000원
26.
2022.12
구독 인증기관 무료, 개인회원 유료
In this paper, durability verification of forged wheels for automobiles were performed using the finite element method for bending fatigue analysis and impact analysis. In addition, the durability analysis environment of forged wheels was implemented. By analyzing the stress distribution on the surface of the forged wheel, the area with a high possibility of breakage was identified and improved. The durability analysis of the initial model forged wheel was performed by bending fatigue analysis and impact analysis, The stress distribution of the forged wheel surface was analyzed through the analysis results of the initial model. and the spokes, flanges, hubs, and rear parts are less likely to be damaged were cut to reduce the weight by about 10%, and the reliability of the improved model was confirmed.
4,000원
27.
2022.12
구독 인증기관 무료, 개인회원 유료
Screw jet equipment has been developed based on the existing accumulated experimental indicators in the semiconductor industry, and for specific performance development, it is necessary to visually check a process in which a high viscosity solution is discharged to a nozzle through a screw. Since the transparency of the exterior is not guaranteed after design and production due to the characteristics of the equipment, simulation must be performed to confirm the performance data according to the internal shape. Therefore, in this study, the screw jet equipment was simulated using the moving particle system, and through this, all processes of the screw jet internal solution flow were visually checked and computerized data capable of predicting the performance of the equipment was secured.
4,000원
28.
2022.12
구독 인증기관 무료, 개인회원 유료
Submarining is a phenomenon in that the lap belt goes over the pelvis of the occupant during a frontal crash. It is known to be one of the causes of serious abdominal injuries for the belted occupant. The goal of the current study was to investigate the effect of both the belt geometry and dummy variations on the occurrence of submarining. A series of quasi-static belt-pull tests were performed to evaluate the influence of the parameters on the occurrence of the submarining. The main influencing factor of the submarining was the lap belt angle. The tear or wrinkle of the dummy clothing and torso angle relative to the pelvis also affected the propensity of the submarining. Therefore, these parameters need to be closely monitored to obtain repeatable test results.
4,000원
29.
2022.12
구독 인증기관 무료, 개인회원 유료
Welding is a representative processing technology applied in many industrial sites due to its quality and convenience. In particular, fiber laser welding can be welded at a faster speed compared to arc welding, and there is an advantage in welding distortion, which is the most significant disadvantage of welding. In this study, the weldable thickness was predicted, and the optimal welding angle was estimated using simulations during the welding of the T-shape structure. The multi-layer heat source model proposed in the previous author's study was used, and the study was conducted using the proposed welding heat source under specific conditions of 4kw and 1.0m/min. As a result, it was predicted that high-quality welding would be possible when the thickness was 3mm or 4mm, and it was also confirmed that welding should be performed at an angle of 82.5° or more when welding a 3mm thick structure. As a follow-up study, we plan to build a welding heat source model under various conditions and conduct a study to derive welding conditions at various thicknesses.
4,000원
30.
2022.12
구독 인증기관 무료, 개인회원 유료
This study chiefly aims to clarify efficient methods considering behavioral pattern of refugees in multi-use facilities which can be applied to architectural planning. Accordance with COVID-19 situation, it is mandatory to check the temperature of visitors as a measure for the prevention of COVID-19 in multiuser facilities. When disaster occurs, for people in multi-use facilities such as medical facilities, museum, concert hall etc, it is difficult to find out short and right route to outside since the spatial characteristics are not familiar to visitors. If we design floor plans and circulation system considering behavioral pattern of refugees we can prevent the spread of disasters when they happen.
4,000원
31.
2022.12
구독 인증기관 무료, 개인회원 유료
The characteristics of pollutant emission for non-premixed flames with LCG 8000 and LCG 6000 represented as low calorific gases were investigated by numerical simulation. Commercial software (ANSYS 16.2 - FLUENT) is used to predict 2-D pollutant emission with GRI 3.0 detailed reaction mechanism. In addition, the addition of hydrogen to LCG 6000 was also considered. As result, the flame length and temperature of LHVGs were decreased with decreasing calorific value at the same condition. In addition, NO concentration was decreased as temperature decreased. However, CO concentration for LCG 8000 predicted to be slightly higher than that for methane due to the high propane concentration. In the case of LCG 6000 with added hydrogen, the flame length was the shortest and NO concentration was the highest due to the highest flame temperature, but CO concentration decreased rapidly due to the addition of the carbon-free fuel.
4,000원
32.
2022.12
구독 인증기관 무료, 개인회원 유료
The purpose of this study was to develop a side protection device for school buses for children. In the case of the door side impact beam, it plays a very important role because it protects passengers from external collisions. However, in the case of a school bus for children, the space between the door and the door trim is very narrow, unlike a general passenger car. So, as an alternative to this, we are trying to develop Rub Rail, which is compulsory for children's school buses in the United States. Based on the results of structural analysis according to the cross-sectional shape of the rub rail, we want to find out the appropriate shape of the rub rail.
4,000원
33.
2022.12
구독 인증기관 무료, 개인회원 유료
In this paper, the mechanical properties according to the rCF weight percent(10, 20, 30, 40, 50wt%) of the rCFRP specimen were evaluated and analyzed. First, to prepare rCFRP specimens, pellets were prepared according to the type of weight percent, and rCFRP tensile specimens according to ASTM D638 were prepared using an injection molding machine. Tensile tests were performed on each of 10 specimens according to weight percent conditions, and tensile strength and modulus of elasticity were calculated. For a detailed analysis of the correlation between the internal structure of the specimen and the mechanical properties, the weight percent to the constituent materials of the rCFRP specimen was calculated using mCT and used for the analysis of mechanical properties. For a more detailed analysis, a detailed analysis of the mechanical properties of rCFRP was performed through the fracture surface analysis of the specimen using FE-SEM.
4,000원
34.
2022.12
구독 인증기관 무료, 개인회원 유료
In the automobile manufacturing industry, lightweight design is one of the essential challenges to be solved fundamentally. The vehicle wheels are classified as safety related components as the main substructure of the vehicle. In this study, we illustrate a technique for selecting the appropriate number of spokes. Based on the basic model of the selected number of spokes, we propose a method to maintain stiffness and design lightweight using topology optimization software. Based on the basic model of the selected number of spokes, it was redesigned to be lightweight while maintaining stiffness by utilizing topology optimization software. By comparing and reviewing the structural analysis results of the basic model and the redesigned model, a design technique that can maintain structural safety and reduce wheel mass was proposed.
4,000원
35.
2022.12
구독 인증기관 무료, 개인회원 유료
This paper developed a wind triboelectric nanogenerator(TENG) using cubic PTFE model. When the wind is injected, the cube PTFE is scattered inside the cylinder TENG structure and energy is harvested. The TENG structure was designed as a cylinder that allows independent dielectric to rotate well inside. In addition, an inlet and an outlet were made to allow good wind flow. Unlike wind harvesters, where one end is mostly fixed and energy is harvested, the dielectric's motion is freed using independent mode. The electrodes and dielectric materials used Aluminum(Al) and Polytetrafluoroethylene(PTFE). The cube PTFE dielectric contacts/separates the electrode attached to the inner wall of the cylinder along the inner wall of the cylinder. At this time, electricity is generated by the kinetic energy generated by the wind. In this study, the efficiency by the number of Cube PTFE inside the cylinder was compared. The experiment confirmed that as the number of Cube PTFE increases, the power increases, but if the number of Cube PTFE exceeds an appropriate number, the density inside the cylinder increases, interrupting the flow of wind, and thus decreasing the power.
4,000원
36.
2022.12
구독 인증기관 무료, 개인회원 유료
Considering the features of body repair for automotive body where same damage and repair conditions does not exist in car accident, it is essential to acquire know-how and continuously approach new materials and new technologies on the site of maintenance where the theoretical instruction of textbook cannot react accurately minute by minute. Especially, in case of car repair from unexpected accidents such as body repair or dent repair, it is difficult to satisfy vehicle owners despite their request. Accordingly, this study researched the better maintenance technology to restore to its original state with more improved technology as vehicle owners wish. This study made time to repair reduced by 98% and the cost reduced by 79.6% through the accurate diagnostic technique before repair and maintenance technologies of body crash analysis applying property of high-speed tensile. It also obtains intangible effects including prevention of environmental pollution and maximization of vehicle owners satisfaction.
3,000원
37.
2022.12
구독 인증기관 무료, 개인회원 유료
This paper proposes a method to improve the position control synchronization performance by synchronizing the controller operation between servo drives based on the synchronization signal of the EtherCAT(Ethernet for Control Automation Technology)distributed clock. In order to synchronize the operation of the controller between the servo drives, the phase of the operating frequency of the PWM(Pulse Width Modulation) module for motor control was synchronized based on the synchronization signal. At this time, the operation sequence of the current, speed, and position controller of the servo drive operating based on the PWM operating frequency was rearranged. Therefore, the servo drives on the network run the same controller at the same time. And the time at which the master's command is reflected to the drive's controller and the time at which the drive's status information is acquired coincided among the drives. After establishing an experimental environment in which servo drives are arranged in the EthercCAT network system, we verified that the position synchronization performance between servo drives applying the proposed method is improved.
4,000원
38.
2022.12
구독 인증기관 무료, 개인회원 유료
In this paper, we propose a analysis of domestic and foreign standards on protecting human body from EMF(Electromagnetic filed) and effect of the human body through EMF analysis of military electronic equipment in operation. We measured the EMF intensity of the side lobe and back lobe main beam on Radar Equipment at an accessible position. As a result, it was confirmed that the measured EMF intensity of three types of radar equipment did not exceed the standard on domestic protecting human body from EMF.
4,000원
39.
2022.12
구독 인증기관 무료, 개인회원 유료
This study investigated variables for improving adhesive strength using laser surface treatment when bonding dissimilar materials using adhesives. adhesive strength analysis was performed for CFRP and Al6061 by laser irradiation intensity, and surface roughness was measured to analyze the related results. In the case of CFRP, the adhesive strength was good when the surface was not treated. In the case of Al6061, the adhesive strength was 25 MPa when the surface was treated with 20W, the maximum output of the laser surface treatment equipment, and the adhesive strength was improved by 125% compared to the untreated specimen. In addition, by measuring the surface roughness in the experiment, it was confirmed that the higher the surface roughness, the better the adhesive strength.
4,000원
40.
2022.12
구독 인증기관 무료, 개인회원 유료
We propose a method for developing an in-pipe inspection robot based on multiple inertial sensors. Estimating the position of underground pipelines where satellite signals do not reach remains challenging. High-precision inertial sensors and high-tech mobile robots can be solutions, but their high price limits their general use. We developed an in-pipe inspection robot by combining various low-cost sensors with a microcomputer-based RC car platform. First, we fabricated a multi-inertial sensors module by combining commercial grade low-cost MEMS inertial sensors. The sensor values measured by the multi-inertial sensor are transmitted to the main computer through the MCU, and the attitude angle of the vehicle is finally calculated through the inverse variance weighted average. The travel distance of the robot is estimated by using hall sensors and neodymium magnets attached to the inside of the wheels. Also, we measured the pipe diameter using multiple ultrasonic sensors. We verified the estimation accuracy of each sensor through experiments and consequently estimated the 3D trajectory of the in-pipe robot.
4,000원
