간행물
대한안전경영과학회지 KCI 등재 Journal of Korea Safety Management & Science
- 발행기관 대한안전경영과학회
- 자료유형 학술지
- 간기 계간
- ISSN 1229-6783 (Print)2288-1484 (Online)
- 수록기간 1999 ~ 2024
- 주제분류 공학 > 안전공학 공학 분류의 다른 간행물
- 십진분류KDC 530DDC 620
권호리스트/논문검색
제14권 제1호 (2012년 3월) 26건
1.
2012.03
구독 인증기관 무료, 개인회원 유료
A Development of Cognitive Assessment Tool based on Brain-Computer Interface for Accident Prevention
A number of Brain-Computer Interface (BCI) studies have been performed to assess the cognitive status through EEG signal. However, there are a few studies trying to prevent user from unexpected safety-accident in BCI study. The EEGs were collected from 19 subjects who participated in two experiments (rest & event-related potential measurement). There was significant difference in EEG changes of both spontaneous and event-related potential. Beta power and P300 latency may be useful as a biomarker for prevention of response to safety-accident.
4,000원
2.
2012.03
구독 인증기관 무료, 개인회원 유료
Recently, carelessness on safety management in construction sites has caused a sharper upward trend in accidents and disasters, compared to the past. Therefore, this study analyzes the causes of accidents that occurred on construction sites in the year of 2007, and proposes preventive measures. The construction industry had a heavy death rate with 279 out of 418 deaths from falls in all industrial sites, accounting for 66.7%. And the causation analysis found a particularly high incidence of temporary structure-related accidents, with falling off scaffolding as the most common cause of accidents. According to the causation analysis of fall-down accident cases, accidents induced by protrusion on construction sites are a big contributor resulting in the deaths of 312, accounting for 74.8%, which is deemed to be due to site disorderliness. And to remove floor protrusions and to secure workers' traffic line and safety, neat and thorough site arrangement is necessary. Against collision, efforts must be made to prevent equipment-pedestrian crashes on site, which necessarily requires emergency lamps, alarm bells, and safety poles and blocks to be installed, lighting systems to be improved, obstacles to be removed, site supervisors to be assigned to construction equipment works, and workers to be more intensely trained and supervised.
4,000원
3.
2012.03
구독 인증기관 무료, 개인회원 유료
The statistics of the safety accidents in labs show that the biggest reason for them is researchers' carelessness and insecure actions. In this way, the safety accidents in labs are affected a lot by researchers' safety consciousness. Therefore, in order to prevent the safety accidents in labs, this study aims at measuring the degree of researchers' safety consciousness, grasping the elements affecting their safety consciousness and suggesting the measures to improve the lacking safety consciousness. To accomplish this goal, a survey was conducted and analyzed on the safety consciousness of 1,226 researchers working at 10 government- supported research institutes in Daedeok R&D Complex. As a results, the measures to improve researchers' safety consciousness will be suggested as follows. First, in an environmental aspect, improvement of labs' environment exposed to danger, interest and participation of CEO, regular discussion on the safety in labs, installment of safety equipments in labs, and enlargement of individual labs are necessary. Second, in an educational aspect, the safety education offered by institutes need to be enhanced, experiential safety education fit for the characteristics of research should be applied, the time for safety education must be observed, and the communication among team members through the collective education in department units and safe culture through the campaigns to enhance safety consciousness have to be established. Third, in a systematic aspect, sanctions have to be imposed on the researchers who do not attend safety education, the number of safety supervisors and safety budget of labs should be increased, a safety certification system need to be introduced when a lab is built, the problems in safety have to be open to all departments and rewards for the persons of merit in labs should be extended.
4,000원
4.
2012.03
구독 인증기관 무료, 개인회원 유료
Recent research on stand-alone focused on the improvement and development of functions for solving problems such as the limited operating time of stand-alone installed at dwelling and their low reliability caused by false alarms, but it is more urgent to study on the operating range of stand-alone sensor in consideration of the impacts of combustion products on residents because the primary goal of fire safety is minimizing casualties. This study purposed to propose the optimized operating range of stand-alone sensor in consideration of the impacts of combustion products on residents. For this purpose, we made a mathematical approach to the change of temperature over the lapse of time in compartment fires similar to house fires, and established the standards of the body's response against heat and smoke based on literature review. In addition, we surveyed domestic and foreign technological standards for stand-alone sensor, and converted them to standards for residents of the body's response against heat and smoke using mathematical model equations and analyzed them comparatively.
4,000원
5.
2012.03
구독 인증기관 무료, 개인회원 유료
This paper dealt with developing conceptual model for making public policy on consumer product safety. The matters of consumer safety, public health and environmental protection are essential parts of making policy for consumer products. Moreover, policy authority should consider all measures based on consumer safety. In the process making regulations, policy authority has to have some methods to prevent errors on treating eligible persons as persons disqualified under uncertainty decision making of public policy. To recognize and ensure fairness on public policy, policy authority needs to establish basic policy making and fundamental concepts. Therefore, we developed conceptual model for consumer products safety, CPSPcon in this paper. The conceptual model is one part of SSM(Soft System Methodology) and can support specific policy target. The CPSPcon model can assist in evaluation of responses to an adapting or considering model.
4,000원
6.
2012.03
구독 인증기관 무료, 개인회원 유료
This study was carried out to observe the impacts of a mouse's inhalation of toxic gas SO2 generated from combustion on its organs by different concentrations. As for research methods: First, after concentrations of SO2 generation from combustion had been set to three: low (10.4 ppm), middle (24.9 ppm) and high (122 ppm) through Gas Toxicity Testing Method (KS F 2271) and SO2 combustion gas was exposed to eight mice in each concentration. Five mice that were able to move based on LD50, a criterion, which sets the down time of a mouse's average behaviors to over 9 minutes, were randomly selected in each concentration, and they were set up as the subjects of the study on toxicity bio-markers. Second, tissues were taken from heart, liver, lungs, spleen and the thymus gland of the mice selected in each concentration and a pathological examination of them was carried out. As a result, microvascular congestion appeared in the heart, and cell necrosis, cortex congestion and tubule medulla congestion, etc. in each concentration were observed in addition to vascular congestion in liver, lungs, spleen and the thymus gland. Also, it was found that the higher the concentrations of SO2 exposure is, the greater, the changes in the organs get. Through this study, SO2 of various toxic gases generated from fire turned out to affect the tissues of each organ of a mouse, it is expected that the toxic gases may greatly affect human body in case of actual fire, and this study is evaluated as having a significance as a basic data on inhalation toxicity assessment of toxic substances generated in combustion.
4,000원
7.
2012.03
구독 인증기관 무료, 개인회원 유료
The purpose of this study is to grasp foreign worker's industrial safety and health state, which find out the improvement to secure the basic safety net for foreign workers. We have investigated 2,050 workers through direct interviews during the period from April 12, 2010 to May 31, 2010. And the result of analysis, foreign worker's daily average working time is 10.6 hours(40.8% workers in total work 10~12 hours), the extent of exposure to harmful and dangerous working environment is 'the position which cause pain in neck, waist, hands, shoulders, legs'(69.3%), 'repetitive hands and arms movement'(66.1%). It showed 'experience of accident damage or disease related work'(27.3%), 'never apply for industrial accident compensation' is revealed high at 73%. As a result of completing a safety health education for a year, it showed 'never educated'(40.2%), 'the institute that foreign workers have used for help and advice is the foreign worker's support center'(61.9%) Thus, hiring foreign workers in the company are small in site, the environment is too harmful and dangerous. In addition, no safety and health managers, legally blind spot located in the health and safety, because it is an urgent meet for these measures to improve.
4,200원
8.
2012.03
구독 인증기관 무료, 개인회원 유료
We studied the risk analysis of fire and explosion caused by gas leak in underground-parking of gas vehicle. However, an entrance regulation of gas vehicles (H2/LPG/CNG etc.) to underground garages has not been enacted in Korea. Incase, a gas explodes in an underground parking garage placed in overcrowded residential area, such as an apartment, the scale of the damage would cause tremendous disaster. Faults of vehicle parts and management problems were evaluated by using the Failure mode and effect analysis (FMEA), which is a qualitative analysis method. The range of the damaged area by the explosion and the damage scale by the explosion pressure were analyzed by using the process hazard analysis software tool (PHAST). The study is expected to facilitate enactment of the regulation for the underground parking to restrict the gas vehicle.
4,000원
9.
2012.03
구독 인증기관 무료, 개인회원 유료
In this study, the representative hand shapes for the adult Koreans were analyzed by factor analysis and cluster analyses. The analyses were conducted on the anthropometric data of 58 hand dimensions from 325 subjects having nonhomogeneous demographics. Maximum hand circumference, first phalanx length of index finger, and ratio between the two measures were the independent variables for the cluster analyses. The results of the study showed that Korean hand shapes can be divided into 2 clusters irrespective of their size for each of the male and female group. There were slight differences in component ratio of hand shapes with respect to the occupation and the age, but their differences were not statistically significant. The representative Korean hand shapes and their anthrpometric dimensions could be used to design and establish proper sizing system for various hand operating devices.
4,200원
10.
2012.03
구독 인증기관 무료, 개인회원 유료
The purpose of this study suggests a personalized algorithm of physical activity energy expenditure prediction through comparison and analysis of individual physical activity. The research for a 3-axial accelerometer sensor has increased the role of physical activity in promoting health and preventing chronic disease has long been established. Estimating algorithm of physical activity energy expenditure was implemented by using a tri-axial accelerometer motion detector of the SVM(Signal Vector Magnitude) of 3-axis(x, y, z). A total of 10 participants(5 males and 5 females aged between 20 and 30 years). The activities protocol consisted of three types on treadmill; participants performed three treadmill activity at three speeds(3, 5, 8 km/h). These activities were repeated four weeks.
4,000원
11.
2012.03
구독 인증기관 무료, 개인회원 유료
This study is about the qualitative safety assessment for hydrogen gas filling facilities in Korea operating with one-bank type. The purpose of this safety assessment is about the development of components for design, fabrication, assembly, operability of dispenser and systems of the safety. For the qualitative safety assessment method, the study used FMEA(failure mode & effect analysis) and HAZOP(hazard & operability). This study evaluated the safety through FMEA and HAZOP then by referring to P&ID and PFD of hydrogen dispenser, thereby examining the dangerousness of the equipments, defects of the structure and problems of the operation.
4,000원
12.
2012.03
구독 인증기관 무료, 개인회원 유료
In this study was conducted numerical analysis to evaluate the stability of BTR(Built-in Timber Roof Tunneling Method), which is one of construction methods of underground structures in the non-opening state. The discretion method was applied to individually model reinforcing members of BTR, and the homogeneity analysis technic by area ratio was used to verify the feasibility comparing this result with that from conventional analysis method. The parameter study was performed to evaluate the effect varying ground depth, distance length of reinforcing supports and to verify the field applicability of new analysis method. The results showed the very precise value with allowable error, so this method can be applied in the field, The more length of supporting members caused the more vertical displacement and the top displacement increment of support members is larger than that of ground surace. The effect of ground depth was more impressive than that of distance length of reinforcing supports.
4,000원
13.
2012.03
구독 인증기관 무료, 개인회원 유료
It could be debated that the owners were indemnified from the charterers even in respect of the loss of deck cargo caused by the negligence on the part of the owners' servants by a clause 13(b) of NYPE(1993) form, where NYPE(1993) incorporated the Hague/Visby Rules by a paramount clause and did not contained an on deck statement to state or identify what or how much deck cargo was being carried, however the relevant bills of lading all had such statement. The socol 3 of U.K. is a very helpful decision on (1) an on deck statement in bill of lading was sufficient to exclude application of the Hague/Visby Rules to the carriage of deck cargo, as a result, the clause 13(b) should not be null and void by the clause 3(8) of the Hague/Visby Rules (3) the clause 13(b) could not protect the owners from the loss and/or liability caused by negligence and/or breach of the obligation of seaworthiness on the part of the owners, their servants and agents. Therefore, the purpose of this study is to critically analyze the decision in the socol 3, and provide the decision's practical implications in order to prevent legal disputes as to the on deck carriage between the owners and the charterters.
4,000원
14.
2012.03
구독 인증기관 무료, 개인회원 유료
This paper deals with the productivity increment through construction of lean production system for automobile factory in China. This lean production system has been progressed according to 5 steps. Step 1 is the work preparation. Step 2 is the process design. Step 3 is the establishment of method to count production quantity. Step 4 is the establishment of measuring method for input and output. Finally, step 5 is the construction of flexible production system able to adapt for environment change. This lean production system is expected to obtain the productivity increment by 50% for plastic plant and reduction by 50% in inventory quantity.
4,000원
15.
2012.03
구독 인증기관 무료, 개인회원 유료
This paper deals with the productivity increment through construction of HT8 production system for automobile factory in China. HT8 production system start to build up several management indices. The important management indices consists of organization management, location management, management of order, management of defective item, management of delivery information, and warehouse management. This HT8 production system is expected to obtain the improvement for overall organization management and reduction by 50% in warehouse cost.
4,000원
16.
2012.03
구독 인증기관 무료, 개인회원 유료
This study proposes a collaboration system framework on the web service in a supply chain to implement an efficient virtual supply chain and improve an ability to fulfill received orders over a supply chain. The system based on the framework proposed in this paper plays an important role for automatic order negotiation and placing/receiving an order noticed in web service by the main system. Furthermore, it can evaluate the fulfillment of received orders over a supply chain by using the transaction results from hierarchically related vendors and establish efficient manufacturing plans. In a word, this system is the automated system for creating manufacturing plans, placing and receiving orders. A little more important main function of this system is that it has a dynamic evaluation capability about fulfillment with received orders over a supply chain, and improves the evaluation method of fulfillment ability with received orders with related to direct dealing vendors, which is a main problem in existing system. As a result, this system is able to reduce the work load of the sales and purchasing materials, production control division, to manage accurate inventory promptly, to maintain the optimal inventory level by analyzing the information of fulfillment ability with received orders, and to enhance the level of service for customers.
4,000원
17.
2012.03
구독 인증기관 무료, 개인회원 유료
In the previous study, the construction guide line of IT infra-structure for a u-City was introduced. However, it is only concentrated on the components and construction procedure for provider-oriented and technology-oriented sensor networks. In this paper the architecture and building process of demander-oriented sensor networks for sustainable u-City service are proposed. In the paper it is described (1) the enhancement methods of the procedure that can be flexibly constructed according to the scale of the project, (2) the methods that can improve the structure from the wireless sensor network such as RFID/USN to the hybrid sensor network, and (3) the consideration factors for providing the sustainable u-City service.
4,000원
18.
2012.03
구독 인증기관 무료, 개인회원 유료
The medium and small logistic companies that have an outsourcing contract from the large corporation are encountered with a problem to introduce the ERP system to their current business environment due to following risk of change in current business environment, high cost involved in investment, and lack of understanding of business requirement of ERP. Instead of build their own ERP system, the small and medium logistic companies are using the large corporation's ERP system and get the benefit of efficiency in management and control process. Therefore, it is more like the organization hierarchy, not collaboration between the medium and small companies with the large corporation. In this study, the survey method to find out how the medium and small logistic companies understand the importance of ERP system on continuous growth of business by AHP. as result, they are recognized. The benefit of the ERP system as having much effect on business competitiveness.
4,000원
19.
2012.03
구독 인증기관 무료, 개인회원 유료
This essay talks about research of robust design for quality improvement of production procedure of Wet Etchant. It suggested the optimum design method in consideration of specific capability value that is the way to maximize the quality of product in the production system by using Daguchi parameter design method while finding factors affecting product quality with analysis of production system of product A from producer D. Also, it set long term of 6months as noise factor and let it to be the robust design that can find the optimum condition of control factor that is dull to the changes of each month, that is the change in noise factor. The control factor which affects the product quality is decided as combination method, temperature of raw material, combination time and as there are too many possibilities for combination methods, we performed 4 methods first based on previous research data then derived three ways with product that passed SPEC and set as the factor. As a result of application of optimum production procedure suggested in this essay to the actual production process with its standardization, there was a effect of drop of more than 10particles in comparison to the particle number of previous product and also it brought the effect that resulted the stable number of particle of under 30 that is what the client company suggested.
4,200원
20.
2012.03
구독 인증기관 무료, 개인회원 유료
In this paper, we raised the performance of heuristic algorithm to assign job to workers in parallel line inspection process without sequence. In previous research, we developed the heuristic algorithm. But the heuristic algorithm can't find optimal solution perfectly. In order to solve this problem, we proposed new method to make initial solution called FN(First Next) method and combined the new FN method and old FE method using previous heuristic algorithm. Experiments of assigning job are performed to evaluate performance of this FE+FN heuristic algorithm. The result shows that the FE+FN heuristic algorithm can find the optimal solution to assign job to workers evenly in many type of cases. Especially, in case there are optimal solutions, this heuristic algorithm can find the optimal solution perfectly.
4,200원
1
2
