간행물
대한안전경영과학회지 KCI 등재 Journal of Korea Safety Management & Science
- 발행기관 대한안전경영과학회
- 자료유형 학술지
- 간기 계간
- ISSN 1229-6783 (Print)2288-1484 (Online)
- 수록기간 1999 ~ 2024
- 주제분류 공학 > 안전공학 공학 분류의 다른 간행물
- 십진분류KDC 530DDC 620
권호리스트/논문검색
제21권 제2호 (2019년 6월) 4건
1.
2019.06
구독 인증기관 무료, 개인회원 유료
Most of gas turbine combined cycle power plants are located in urban areas to provide peak load and district heating. However, NOx(nitrogen oxides) of exhaust gas emission from the power plants cause additional fine dust and thus it has negative impact on the urban environment. Although DLN(dry low NOx) and multi-stage combustors have been widely applied to solve this problem, they have another critical problem of damages to combustors and turbine components due to combustion dynamic pressure. In this study, the effect of different fuel ratio on NOx emission and pressure fluctuation was investigated regarding two variable conditions; combustor stages and power output on M501J gas turbine.
4,000원
2.
2019.06
구독 인증기관 무료, 개인회원 유료
Gondola is widely used as a construction facility to perform external finishing work without using scaffolding at a construction site. However, since 2000, there have been 17 deaths from now so these risks associated with work can not be ignored. Therefore, it is expected that it will contribute greatly to prevent related disasters if introducing necessary measures to prevent repeated related disasters and installing additional safety devices. In order to eliminate the risk factor according to the operation of the gondola, it is necessary for the operator to use it to use it while the examination of each product is completed, and to use the over load Dangerous arbitrary measures such as arbitrary operation of the prevention device, removal of the safety fence for convenience of work, installation of the wire rope installed in the air, falling out of the wire rope and falling to the ground Do not perform such sealing measures so that any operation of the overload prevention device can not be done so as not to take such arbitrary measures, or wire the power supply wire to the safety fence so as not to delete the safety fence. Then, when the safety fence is removed, so that it does not become a gondola operation, or when replacing the wire rope in the air, to prevent the wire rope from coming off, Additional measures such as installing falling down prevention device may be necessary.
4,000원
3.
2019.06
구독 인증기관 무료, 개인회원 유료
Among service industries of knowledge based economic era, the roles of educational service field are becoming more important and standard of educational service makes a direct effect on economic development and social growth. Therefore, accurate measurement of service quality is the most important assignment and the measurement of the service quality remains difficult assignment. So, this researcher classified quality attributes applying weighted value and found potential satisfaction level(PSL) and potential customer demand improvement index(PCDI) for trainees participating in national manpower business so as to suggest measurement of service quality and easiness of use and then, calculated satisfaction position and opportunity cost by quality factor with Taguchi’s loss fraction. And, improvable satisfaction level was measured, opportunity cost by degree of customer dissatisfaction was quantitatively measured, and a model that can indicate with economic factors was suggested. In addition, methodology of measuring quality cost that can be reduced by quality improvement and direction of strategic decision-making for deciding items to be improved preferentially were suggested with qualitative index that can indicate the degree of customers’ dissatisfaction by loss.
5,200원
4.
2019.06
구독 인증기관 무료, 개인회원 유료
The government announced that it would ask the contractors not only the supplier but also the contractors to take the same responsibilities if they did not observe industrial accident safety measures from 2019. The semiconductor manufacturing process belongs to the representative disaster industry group in which the facility is directly located inside a closed space called clean room. According to previous studies, the semiconductor industry group used checklists for safety management of their suppliers. This study has developed a model for assessing suppliers by constructing a quantitative checklist item through the risk assessment methodology, laws and regulations. The evaluation model of the supplier set up through this study becomes the safety management standard in the semiconductor industry .Furthermore, it is applied to the partner companies in the operation of ISO 14001, 45001, I would like to apply it as a measure of performance management for CSR (Corporate Social Responsibility).
5,200원
