간행물
대한안전경영과학회지 KCI 등재 Journal of Korea Safety Management & Science
- 발행기관 대한안전경영과학회
- 자료유형 학술지
- 간기 계간
- ISSN 1229-6783 (Print)2288-1484 (Online)
- 수록기간 1999 ~ 2024
- 주제분류 공학 > 안전공학 공학 분류의 다른 간행물
- 십진분류KDC 530DDC 620
권호리스트/논문검색
제20권 제3호 (2018년 9월) 6건
1.
2018.09
구독 인증기관 무료, 개인회원 유료
This study is intended to look into the effect of construction safety supervision system on risk control and reduction. To achieve this, a survey was carried out to 114 companies in construction, ordering, contract and management. The overall findings were as follows. The effect of construction safety supervision system on risk control and reduction showed that factors of supervision system, supervision cost and supervision method had a positive effect on risk control and reduction. And their perception of the introduction of safety supervision system in construction sites according to process showed that there was a difference between them according to the field of ordering, contract and supervision. There was the biggest difference between owner and contractor in double supervision system, but no difference between them in the perception of risk reduction. These results show that all ordering, contract and supervision are positively needed for the introduction of construction safety supervision. This means that there is a difference between owner and contractor in the perception of process according to system operation. All companies agree to system improvement by the settlement of safety supervision system for the prevention of safety accidents and safe construction, but the systematic complement of safety supervision is the burden of contractor. And there is a big difference between owner and contractor in the perception of responsibility and concern for cost burden.
4,000원
2.
2018.09
구독 인증기관 무료, 개인회원 유료
This study suggests a model of production information system that can reduce manufacturing lead time and uniformize quality by using DNC S/W as a part of constructing production information management system in the industrial field of the existing marine engine block manufacturing companies.
Under the effect of development of this system, the NC machine interface device can be installed in the control computer to obtain the quality information of the workpiece in real time so that the time to inspect the process quality and verify the product defect information can be reduced by more than 70%. In addition, the reliability of quality information has been improved and the external credibility has been improved.
It took 30 minutes for operator to obtain, analyze and manage the quality information when the existing USB memory is used, but the communication between the NC controller computer and the NC controller in real time was completed to analyze the workpiece within 10 seconds.
4,000원
3.
2018.09
구독 인증기관 무료, 개인회원 유료
This paper describes result of a study on safety against a fire of charging cable for mobile phone for vehicle. Combustion on the USB cable in the car was happened while driving. Gas coming from the burning USB cable could be a reason which can make a secondary car accident since the driver also can be embarrassed while driving. In order to prevent a secondary car accident connected on the road, to research a reason why USB cable can emit gas and be burned in charging. We did simulation test with abnormal fault condition for the electronic component on the board in the USB cable. So we get the result from abnormal fault condition simulation test, for instance, shorted test for output terminal of 8 pin switch, shorted test for chip resistor after thermal aging in the condition 25 ℃ , 93 % RH during 48 hours. To analysis the result of all test, Combustion on the USB cable was not the 8 pin but other electrical component such as a chip resistor. Therefore we guess that the reason for USB cable combustion in charging in a car was not 8 pin and a LED but another defective component.
4,000원
4.
2018.09
구독 인증기관 무료, 개인회원 유료
The steel pipe manufacturing industry deals with facilities and materials. Especially thermal facilities are close to vapor cloud explosion (VCE) and may cause secondary damage to facilities because they deal with corrosive substances such as hydrofluoric acid, sulfuric acid and acid, fire, explosion, leakage etc. It is in danger. In this study, hazard identification method was conducted using HAZOP techniques and quantitative risk analysis was conducted using e-CA, a program that supports accident impact analysis. Equipment in the influence range of ERPG - 3 was determined to be a facility requiring replacement. It was decided that neutralization is necessary using slaked lime. Based on the cost of loss, We presented the proper replacement which is the timing of the dangerous facility. As a result, It was ideal to replace the facilities with 20 years of heat treatment facilities, one year of hydrofluoric acid storage tank, 20 years of sulfuric acid storage tank, and 5 years of hydrochloric acid storage tank.
4,000원
5.
2018.09
구독 인증기관 무료, 개인회원 유료
According to enhancement of roles and functions of enterprises’ distribution centers, recent trend of distribution centers are specialization and diversification which have generated lots of new distribution center building or expansion of the existing ones and led attention on stock transfer importance in case of distribution center relocation.
This thesis is a study for how to reduce stock transfer leadtime in order to minimize business risk and how to increase inventory accuracy when stock ownership is transferred in case of distribution center relocation, and to provide inventory accuracy management methods and inventory in/out management types, detailed definition to evaluate level for inventory accuracy management and pros/cons by inventory in/out management type assuming ‘the higher inventory accuracy before stock transfer, the shorter stock transfer leadtime when distribution center is relocated'.
This thesis provides detailed procedure to secure an absolute stock transfer leadtime and process to confirm hugh inventory accuracy by stakeholders which should be sloved by Task Force Team for stock transfer in case of distribution center relocation.
4,000원
6.
2018.09
구독 인증기관 무료, 개인회원 유료
The purpose of this research was to test the effects of technological innovation capability and technology commercialization capability on new product performance of the companies in electronics industry and the moderating role of perceived usefulness of government R&D support. For this study, Research data were collected through questionnaire instruments from the sample of 346 employees in 17 electronics companies of metropolitan area. The 305 sample was selected and analyzed by hierarchical regression technique.
The results showed that technological innovation capability and technology commercialization capability had a positive effect on new product performance. And also found out perceived usefulness of government R&D support had the moderate roles between only technical innovation system our of three technological innovation capability factors and new product performance, and also between only manufacturing capability our of three technological commercialization capability factors and new product performance. With the research results, the implications for electronics company were discussed, and the directions for future research were suggested.
5,100원
