간행물
Carbon Letters KCI 등재 Carbon letters
- 발행기관 한국탄소학회
- 자료유형 학술지
- 간기 격월간
- ISSN 1976-4251 (Print)2233-4998 (Online)
- 수록기간 2000 ~ 2024
- 주제분류 자연과학 > 자연과학일반 자연과학 분류의 다른 간행물
- 십진분류KDC 530DDC 620
권호리스트/논문검색
Vol.33 No.7 (2023년 12월) 38건
21.
2023.12
구독 인증기관 무료, 개인회원 유료
This study presents the fabrication and application of a graphene-assisted voltammetry platform for the sensitive detection of nitrate ions in PM2.5 (atmospheric aerosols with a maximum diameter of 2.5 μm). The MoS2/ reduced graphene oxide/ glassy carbon electrode ( MoS2/rGO/GCE) was prepared using a simple and efficient electrochemical deposition method. The rationale behind selecting MoS2/ rGO stems from their individual properties that, when combined, can enhance the electrode’s performance. MoS2 offers excellent electro-catalytic activity and selectivity for nitrate ion detection, while rGO provides high conductivity and a large surface area for enhanced sensitivity. The electrochemical performance of MoS2/ rGO/GCE was investigated and compared with MoS2/ GCE and bare GCE using cyclic voltammetry and electrochemical impedance spectroscopy. The results demonstrated that MoS2/ rGO/GCE exhibited enhanced electro-catalytic activity, high conductivity, and improved selectivity for nitrate ion detection. The optimal pH value for detecting nitrate ions was determined to be 8.0. Differential pulse voltammetry (DPV) was employed to investigate the linear range and detection limit of nitrate ions on MoS2/ rGO/GCE, resulting in a linear range from 1 to 300 μM and a detection limit of 0.35 μM. The reproducibility and the stability of MoS2/ rGO/GCE were assessed, showing satisfactory performance. Real sample analysis from Chengdu City showed a strong correlation between the results obtained using MoS2/ rGO/GCE and ion chromatography, highlighting its potential application in monitoring nitrate ions in PM2.5. The findings of this study contribute to the development of a graphene-assisted voltammetry platform for sensitive nitrate ion detection in PM2.5, offering potential benefits for real-time air pollution monitoring and environmental health assessments.
4,000원
22.
2023.12
구독 인증기관 무료, 개인회원 유료
Dimethyl silicone oil is widely used due to its excellent thermal stability and good wetting properties. In this study, a series of thermal conductive materials was prepared by physically blending and chemically loading graphene as a thermal conductive filler into dimethyl silicone oil, and their thermal conductivity and tribological properties were investigated. The thermal conductivity of the composites was tested by a thermal conductivity meter and a thermal imaging camera, while the tribological properties of the composites were evaluated using a CSM friction and wear tester. The results showed that both thermal conductivity and tribological properties were improved to a certain extent. The particle size and amount of graphene had a significant influence on the thermal conductivity. For graphene with a single particle size, the thermal conductivity increased with increasing graphene content. The friction coefficient under dry friction conditions was significantly reduced by adding graphene to the silicone oil, as revealed by the friction and wear test.
4,000원
23.
2023.12
구독 인증기관 무료, 개인회원 유료
Hao Wang, Haitao Wang, Jingjing Yang, Pramitha Yuniar Diah Maulida, Jing Zou, Arramel, Can Wu, Jizhou Jiang
Black phosphorus (BP) is incorporated in the electrochemical detection of uric acid (UA) to form few layers of BP nanosheets (BPNS)-modified glassy carbon electrodes (BPNS/GCE), investigated by means of ultrasound-assisted liquid-phase exfoliation. We find a significant increase in the peak current magnitude and positive potential shift in the electrochemical response of BPNS/GCE, which may be attributed to the larger specific surface area and good charge transfer ability of BPNS. Further, the electrochemical response of BPNS/GCE is evaluated under different conditions to achieve the optimal conditions. UA detection using differential pulse voltammetry (DPV) shows linear response within the range of 1–1000 μM with a detection limit of 0.33 μM. This work reveals new applications of BP nanomaterials in the electrochemical sensing, thereby promoting further advancement in terms of practical applications of two-dimensional nanomaterials.
4,000원
24.
2023.12
구독 인증기관 무료, 개인회원 유료
The nanostructured dysprosium oxide ( Dy2O3) was synthesized by the co-precipitation method and incorporated with graphitic carbon nitride (g-C3N4) using the ultrasonication method. The resultant product is denoted as Dy2O3/ g-C3N4 nanocomposite which was further used for electrochemical sensing of riboflavin (RF). The physicochemical properties of Dy2O3/ g-C3N4 nanocomposite were examined using several characterization techniques. The obtained results exhibit the nanocomposite formation with the preferred elemental compositions, functional groups, crystalline phase and desired surface morphology. The electrocatalytic performance of Dy2O3/ g-C3N4 nanocomposite was scrutinized with a glassy carbon electrode (GCE) via differential pulse voltammetry (DPV) and cyclic voltammetry (CV) techniques with the conventional three-electrode system. The modified electrode distributes more active surface area suggesting high electrocatalytic activity for the RF detection with two linear ranges (0.001–40 μM and 40–150 μM), a low detection limit of 48 nM and sound sensitivity (2.5261 μA μM−1 cm− 2). Further, the designed sensor possesses high selectivity, excellent stability, repeatability and reproducibility. Finally, the fabricated sensor was successfully estimated for the detection of RF in actual food sample analysis using honey and milk with better recovery.
5,200원
25.
2023.12
구독 인증기관 무료, 개인회원 유료
A carbon matrix for high-capacity Li/Na/K-alloy-based anode materials is required because it can effectively accommodate the variation in the volume of Li/Na/K-alloy-based anode materials during cycling. Herein, a nanostructured porous polyhedral carbon (PPC) was synthesized via a simple two-step method consisting of carbonization and selective acid etching, and their electrochemical Li/Na/K-ion storage performance was investigated. The highly uniform PPC, with an average particle size of 800 nm, possesses a porous structure and large specific surface area of 258.82 cm2 g– 1. As anodes for Li/Na/K-ion batteries (LIBs/NIBs/KIBs), the PPC matrix exhibited large initial reversible capacity, fast rate capability (LIB: ~ 320 mAh g– 1 at 3C; NIB: ~ 140 mAh g– 1 at 2C; KIB: ~ 110 mAh g– 1 at 2C), better cyclic performance (LIB: ~ 550 mAh g– 1; NIB: ~ 210 mAh g– 1; KIB: ~ 190 mAh g– 1 at 0.2C over 100 cycles), high ionic diffusivity, and excellent structural robustness upon cycling, which demonstrates that the PPC matrix can be highly used as a carbon matrix for high-capacity alloy-based anode materials for LIBs/NIBs/KIBs.
4,000원
26.
2023.12
구독 인증기관 무료, 개인회원 유료
Muhammad Thalhah Zainal, Norikhwan Hamzah, Mazlan Abdul Wahid, Natrah Kamaruzaman, Cheng Tung Chong, Mohd Hanafi Ani, Shokri Amzin, Tarit Das, Mohd Fairus Mohd Yasin
The conventional multi-scale modelling approach that predicts carbon nanotube (CNT) growth region in heterogeneous flame environment is computationally exhaustive. Thus, the present study is the first attempt to develop a zero-dimensional model based on existing multi-scale model where mixture fraction z and the stoichiometric mixture fraction zst are employed to correlate burner operating conditions and CNT growth region for diffusion flames. Baseline flame models for inverse and normal diffusion flames are first established with satisfactory validation of the flame temperature and growth region prediction at various operating conditions. Prior to developing the correlation, investigation on the effects of zst on CNT growth region is carried out for 17 flame conditions with zst of 0.05 to 0.31. The developed correlation indicates linear ( zlb=1.54zst +0.11) and quadratic ( zhb=zst(7-13zst )) models for the zlb and zhb corresponding to the low and high boundaries of mixture fraction, respectively, where both parameters dictate the range of CNT growth rate (GR) in the mixture fraction space. Based on the developed correlations, the CNT growth in mixture fraction space is optimum in the flame with medium-range zst conditions between 0.15 and 0.25. The stronger relationship between growth-region mixture-fraction (GRMF) and zst at the near field region close to the flame sheet compared to that of the far field region away from the flame sheet is due to the higher temperature gradient at the former region compared to that of the latter region. The developed models also reveal three distinct regions that are early expansion, optimum, and reduction of GRMF at varying zst.
4,300원
27.
2023.12
구독 인증기관 무료, 개인회원 유료
Mg81Ni19-8wt.% REO (oxides of Lanthanum and Cerium) alloys were successfully prepared using mechanical alloying method with Mg-Ni alloy and REO powder. Phase analysis, structural characterization, and microstructure imagine of the alloys were conducted using X-ray diffraction (XRD), metallurgical microscope, and transmission electron microscopy (TEM) methods. Multi-phase structures, including the primary phase of Mg2Ni and several secondary phases of Mg + Mg2Ni, MgNi-LaO, and MgNi-CeO, were found in in the as-cast Mg81Ni19- 8wt.% REO alloys. XRD and TEM results showed that Ce exhibits variable valence behavior at various stages, and the addition of REO promotes the nanocrystalline of the alloy. The hydrogen absorption capacity of ball-milled Mg81Ni19 and Mg81Ni19- 8wt.%REO alloy for 2 h at 343 K is 1.34 wt.% and 1.83 wt.%, which are much larger than 0.94 wt.% of as-cast Mg81Ni19 alloy. The addition of REO led to a decrease of the thermal decomposition temperature of the alloy hydride by approximately 20 K and a reduction of the activation energy of the hydrogen desorption reaction by 10% and 13%, respectively.
4,300원
28.
2023.12
구독 인증기관 무료, 개인회원 유료
Esakkimuthu Shanmugasundaram, Chandramohan Govindasamy, Muhammad Ibrar Khan, Vigneshkumar Ganesan, Vimalasruthi Narayanan, Kannan Vellaisamy, Rajaram Rajamohan, Stalin Thambusamy
Carbon nanofibers (CNFs) are promising materials for the construction of energy devices, particularly organic solar cells. In the electrospinning process, polyacrylonitrile (PAN) has been utilized to generate nanofibers, which is the simplest and most popular method of creating carbon nanofibers (CNFs) followed by carbonization. The CNFs are coated on stainless steel (SS) plates and involve an electropolymerization process. The prepared Cu, CNF, CNF–Cu, PANI, PANI–Cu, CNF–PANI, and CNF–PANI–Cu electrode materials’ electrical conductivity was evaluated using cyclic voltammetry (CV) technique in 1 M H2SO4 electrolyte solution. Compared to others, the CNF–PANI–Cu electrode has higher conductivity that range is 3.0 mA. Moreover, the PANI, CNF–PANI, and CNF–PANI–Cu are coated on FTO plates and characterized for their optical properties (absorbance, transmittance, and emission) and electrical properties (CV and Impedance) for organic solar cell application. The functional groups, and morphology-average roughness of the electrode materials found by FT–IR, XRD, XPS, SEM, and TGA exhibit a strong correlation with each other. Finally, the electrode materials that have been characterized serve to support and act as the nature of the hole transport for organic solar cells.
4,500원
29.
2023.12
구독 인증기관 무료, 개인회원 유료
Liquid phase exfoliation of natural graphite is an industrially effective solution for graphene preparation. However, many countries have identified natural graphite as a strategic resource and restricted its mining. In this report, we used abundant and readily available needle coke (NC) as a graphene exfoliation precursor and sodium carboxymethyl cellulose (CMC) as a dispersant to prepare a sandwich structured conductive graphitized NC nanosheets (GNCNs) by liquid phase exfoliation, freeze-drying and high-temperature graphitization, in which a graphene layer is sandwiched between two thin CMC layers. CMC could increase the liquid absorption and retention ability of the conductive agent and improve the migration rate of lithium ions. The highly ordered graphene layer could accelerate the transmission of electrons. The GNCNs with 0.4 wt% CMC addition showed good rate performance (144.6 mAh g− 1 at 5 C) and high cycle stability (96.2% after 200 cycles at 1 C) for LiFePO4 (LFP) battery. The traditional Super-P (SP) conductive agent exhibited low-rate performance (113.9 mAh g− 1 at 5 C) and cycle performance (89.9% after 200 cycles at 1 C). This study offers a novel approach to selecting graphene precursors and has promising applications for conductive additives in high-performance LFP batteries.
4,800원
30.
2023.12
구독 인증기관 무료, 개인회원 유료
Cellulose has experienced a renaissance as a precursor for carbon fibers (CFs). However, cellulose possesses intrinsic challenges as precursor substrate such as typically low carbon yield. This study examines the interplay of strategies to increase the carbonization yield of (ligno-) cellulosic fibers manufactured via a coagulation process. Using Design of Experiments, this article assesses the individual and combined effects of diammonium hydrogen phosphate (DAP), lignin, and CO2 activation on the carbonization yield and properties of cellulose-based carbon fibers. Synergistic effects are identified using the response surface methodology. This paper evidences that DAP and lignin could affect cellulose pyrolysis positively in terms of carbonization yield. Nevertheless, DAP and lignin do not have an additive effect on increasing the yield. In fact, combined DAP and lignin can affect negatively the carbonization yield within a certain composition range. Further, the thermogravimetric CO2 adsorption of the respective CFs was measured, showing relatively high values (ca. 2 mmol/g) at unsaturated pressure conditions. The CFs were microporous materials with potential applications in gas separation membranes and CO2 storage systems.
4,500원
31.
2023.12
구독 인증기관 무료, 개인회원 유료
In this study, we investigate the impact of Isophorone diisocyanate functionalized graphene oxide (IPDI-GO) on the flame retardancy of rigid polyurethane foam (RPUF). IPDI-GO was synthesized and introduced into the RPUF matrix. The flame retardancy of RPUF was significantly enhanced by the incorporation of IPDI-GO, as evidenced by a reduction in peak heat release rate (PHRR) by 25% and total smoke production (TSP) by 15% in comparison to pure RPUF when IPDI-GO was incorporated at 3 wt%. Scanning electron microscopy (SEM) revealed that IPDI-GO contributed to the formation of a compact, continuous char layer on the RPUF surface. This study underscores the potential of IPDI-GO as a promising flame retardant additive for RPUF.
4,000원
32.
2023.12
구독 인증기관 무료, 개인회원 유료
Pharmaceutical products occurring in freshwater bodies create numerous problems for the water bodies owing to their bio-toxic nature. In order to remove such pharmaceutical pollutants, a novel Er-doped Bi4O5Br2/ g-C3N5 nanocomposite was prepared by one-pot synthesis and applied for the photocatalytic removal process. The Er ions doped on the surface of Bi4O5Br2/ g-C3N5 nanocomposite exhibited 97% degradation of tetracycline in 60 min under visible light irradiation, which is higher than pure g-C3N5 and Bi4O5Br2 photocatalysts. The improved photocatalytic properties are attributed to the outstanding visible light harvesting capacity and quick charge carrier separation efficiency which greatly reduced the recombination rate in the heterojunctions. Based on radical trapping experiments, the •O2 −, h+ and •OH radicals played a prominent role in the photodegradation reactions under visible light. Finally, the ternary Er-doped Bi4O5Br2/ g-C3N5 nanocomposite is effectively recyclable with quite a stable photocatalytic removal rate. This work enables a new perspective on the rational design of rare-earth-based nanocomposites for various pharmaceutical pollutants treatment processes.
4,000원
33.
2023.12
구독 인증기관 무료, 개인회원 유료
Hybrid nanocomposites of aluminium (NHAMMCs) made from AA5052 are fabricated via stir casting route by reinforcing 12 wt% Si3N4 and 0.5 wt% of graphene for usage in aeronautical and automotive applications due to the lower density and higher strength to weight proportion. The wear characteristics of the NHAMMCs are evaluated for different axial load, rotational speed, sliding distance and sliding time based on Box-Behnken design (BBD) of response surface methodology (RSM). Orowan strengthening mechanism is identified from optical image which improves the strength of the composite. Outcomes show that with higher axial load and rotational speed, there is substantial increase in wear loss whereas with increased sliding distance and sliding time there is no considerable increase in wear loss due to the lubricating nature of the reinforced graphene particles since it has higher surface area to volume ratio. Besides, artificial intelligence approach of neuro-fuzzy (ANFIS) model is developed to predict the output responses and the results are compared with the regression model predictions. Prediction from ANFIS outplays the regression model prediction.
6,400원
34.
2023.12
구독 인증기관 무료, 개인회원 유료
Fluorine (F) recovery from wet process phosphoric acid (WPA) is essential for sustainable resource utilization and environmental protection. This work systematically investigates the F recovery mechanism by air stripping from three simulated systems: H3PO4- H2SiF6-H2O, H3PO4- HF-H2O, H3PO4- H2SiF6-HF-Al3+-H2O, and from two industrial systems: WPA and WPA-Al3+ under different stripping temperatures (60–110 ℃) and stripping times (0–120 min). The influence on the existence form of F, the content of Al3+ cations and the addition of active silica on the F removal rate in the phosphoric acid solution is studied by analyzing the changes in the contents of F, P and Si. The results indicate that the F in the form of H2SiF6 is more easily released from the phosphoric acid solution than that in the form of HF. While, the release of F is inhibited in the presence of the Al3+ in the solution due to the formation of Al-F complexes that are characterized by 19F NMR, 31Si NMR and FTIR techniques. Interestingly, the addition of active silica can promote the conversion of HF to H2SiF6 in the solution and significantly improve the release rate of F. The researching results can provide an important guidance for industrial practice of WPA.
4,500원
35.
2023.12
구독 인증기관 무료, 개인회원 유료
Hierarchically porous carbon foam composites with highly dispersed Fe2O3 nanoparticles confined in the foam pores, facilely fabricated by hydrolysis-driven emulsion polymerization strategy. The as-generated acidic conditions of Fe3+ hydrolysis could catalyze the polymerization of phenolic resin, and the carbon-based composite materials containing iron oxides were obtained in situ. The structural characterization results show that HCF@Fe2O3 NPs-2 electrode has the largest specific surface area (549 m2/ g) and pore volume (0.46 cm3/ g). Electrochemical results indicates that typical HCF@Fe2O3 NPs-2 electrode displays good capacitive properties. including high specific capacitance (225 F/g at 0.2 A/g current density). Excellent magnification performance (capacity retention rate 80% as current density increases from 0.2 to 10 A/g). At the same time, HCF@SnO2 NPs was successfully synthesized by replacing hydrolyzed tin tetrachloride with ferric chloride. This study provides a new idea for the preparation of metal oxide–carbon matrix composites, and also highlights the potential of such carbon foams in application of energy storage.
4,000원
36.
2023.12
구독 인증기관 무료, 개인회원 유료
This work involves the development of a novel waste-derived carbon dots (CDs) conjugated with silver (Ag) nanohybrid system-based Fluorescence Resonance Energy Transfer (FRET) sensor for the detection of melamine. CDs and Ag nanoparticles served as energy donors and energy acceptors, respectively. CDs were synthesized from orange peel waste through a combined hydrothermal and ultra-sonication route. The synthesized CDs had hydroxyl, amino, and carboxyl groups on their surface, explaining that waste-derived CDs can act as reducing and stabilizing agents and showed strong absorption and fluorescence emission at 305 and 460 nm, respectively. The bandgap, linear refractive index, conduction band, and valance band potential of CDs were observed to be 2.86, 1.849, 1.14, and 4.002 eV, respectively. No significant difference was observed in the fluorescence properties at different pH (acid and alkaline) and ionic concentrations. Given their fluorescent nature, the synthesized CDs were used for the detection of melamine. The fluorescence of CDs was found to be quenched by Ag+ due to the FRET energy transfer between CDs to Ag. Notably, the zeta potential of Ag@CDs was changed from − 28.7 mV to − 30.6 mV after the incorporation of Ag+. Ag@CDs showed excellent selectivity and sensitivity toward the sensing of melamine in the aqueous solutions with the limit of detection ~ 0.85 μM. Increasing the melamine level also raises the FL intensity of Ag@CDs. The substrate was effectively used in the detection of melamine in milk as a real application and the recovery percentage was found to be 98.03%. Moreover, other adulterants such as urea and formaldehyde can be detected selectively by Ag@CDs. Overall, the synthesized Ag@CDs can be used as an efficient material for sensing applications involving such food adulterants.
4,600원
37.
2023.12
구독 인증기관 무료, 개인회원 유료
The complexation of silicon with carbon materials is considered an effective method for using silicon as an anode material for lithium-ion batteries. In the present study, carbon frameworks with a 3D porous structure were fabricated using metal–organic frameworks (MOFs), which have been drawing significant attention as a promising material in a wide range of applications. Subsequently, the fabricated carbon frameworks were subjected to CVD to obtain silicon-carbon complexes. These siliconcarbon complexes with a 3D porous structure exhibited excellent rate capability because they provided sufficient paths for Li-ion diffusion while facilitating contact with the electrolyte. In addition, unoccupied space within the silicon complex, combined with the stable structure of the carbon framework, allowed the volume expansion of silicon and the resultant stress to be more effectively accommodated, thereby reducing electrode expansion. The major findings of the present study demonstrate the applicability of MOF-based carbon frameworks as a material for silicon complex anodes.
4,500원
38.
2023.12
구독 인증기관 무료, 개인회원 유료
The present research focuses on the tribological behavior of the AA5083 alloy-based hybrid surface composite using aluminosilicate and multi-walled-carbon nanotube through friction stir processing for automotive applications. The friction stir processing parameters (tool rotation and traverse speed) are varied based on full factorial design to understand their influence on the tribological characteristics of the developed hybrid composite. The surface morphology and composition of the worn hybrid composite are examined using a field-emission scanning electron microscope and an energy-dispersive x-ray spectroscope. No synergistic interaction is observed between the wear rate and friction coefficient of the hybrid composite plate. Also, adhesive wear is the major wear mechanism in both base material and hybrid composite. The influence of friction stir process parameters on wear rate and the friction coefficient is analyzed using the hybrid polynomial and multi-quadratic radial basis function. The models are utilized to optimize the friction stir processing parameters for reducing the rate of wear and friction coefficient using multi-quadratic RBF algorithm optimization.
4,800원
1
2
