간행물
한국환경과학회지 KCI 등재 Journal of Environmental Science International
- 발행기관 한국환경과학회
- 자료유형 학술지
- 간기 월간
- ISSN 1225-4517 (Print)2287-3503 (Online)
- 수록기간 1992 ~ 2023
- 주제분류 자연과학 > 자연과학일반 자연과학 분류의 다른 간행물
- 십진분류KDC 539DDC 628
권호리스트/논문검색
제19권 제6호 (2010년 6월) 13건
1.
2010.06
서비스 종료(열람 제한)
Pollutants from urban pavement consists various kinds of substances which are originated from dry deposition, a grind out tire, corrosive action of rain to pavement and facilities and raw materials of the road etc.. These are major pollutants of urban NPS (Non-point source) during rainfall period. However there is not enough information to control such pollutants for appropriate management of natural water quality. In this study of transportation areas, three monitoring stations were set up at trunk road, urban highway and national road in Gyeongnam province. Runoff flow rate was measured at every 15minutes by automatic flow meters installed at the end of storm sewer pipe within the road catchment area for water quality analysis. Data was collected every 15 minutes for initial two hours of rainfall. Additional samples were collected 1-4 hours interval till the end of rainfall. The monitoring parameters were CODMn, SS, T-N & T-P and heavy metals. The average EMCs of TSS and CODMn were 62.0 mg/L and 24.2 mg/L on the city trunk road, which were higher than those of urban highway and national road, indicating higher pollutant loads due to activities in the city downtown area beside the vehicle. On the other hand, the average EMC of T-N and T-P were in the range of 2.67-3.23 mg/L and 0.19-3.21 mg/L for all the sampling sites. Heavy metals from the roads were mainly Fe, Zn, Cu and Mn, showing variable EMCs by the type of road. From the TSS wash-off analysis in terms of FF(first flush) index, first flush phenomenon was clearly observed in the trunk road(FF : 0.89-1.43). However, such mass delivery behavior was not apparently shown in urban highway(FF : 0.90-1.11) and national road(FF : 0.81-1.41).
2.
2010.06
서비스 종료(열람 제한)
The present study evaluated residential exposure to atmospheric formaldehyde and acetaldehyde according to distance from the a dyeing industry complex (DIC). This purpose was achieved by measuring concurrently the outdoor air concentrations in residences near the DIC and a certain distance away, plus the outdoor air concentrations at two industrial areas within the DIC boundary. Formaldehyde concentrations (median values of 24.3 and 22.5 μg/㎥ in IS1 and IS2, respectively) were higher than acetaldehyde concentrations (median values of 7.4 and 7.3 μg/㎥ in IS1 and IS2, respectively) at both sites. However, there was no significant difference in the industrial outdoor air concentrations of both formaldehyde and acetaldehyde between the two sites. In addition, the median formaldehyde concentration from the residential site near the DIC (RS1) was about 1.5 times higher than that from the residential site far away from the DIC(RS2), and the median acetaldehyde concentration from RS1 was about 1.3 times higher than that from RS2. It is noteworthy that the mean or median risk as well as these maximum risks are well above the USEPA's permissible risk level of 10 -6 from environmental exposure. This suggests that appropriate management for formaldehyde and acetaldehyde is necessary in order to decrease risk of the residents of study areas, regardless of the distance from the DIC.
3.
2010.06
서비스 종료(열람 제한)
Mesoporous silica was prepared from hydrothermal synthesis using gel mixture of tetraethylorthosilcate (TEOS) as silica source and cetyltrimethylammonium bromide (CTMABr) as a surfactant. In the optimum synthesis cause, molar ratio of template and silica changed. The surface and structure properties of mesoporous silica were determined by XRD, SEM, TEM and BET. Also, surface potential of mesoporous silica was measured using zeta potential. N2 adsorption isotherm characteristics, including the specific surface area (SBET), total pore volume (VT), and average pore diameter (DBJH), were determined by BET. As a result, SBET of 100 m² /g～1500 m² /g was determined from the N2 adsorption isotherm. Also, the average pore diameter was 2 nm∼4 nm. Mesoporous silica's surface potential of minus charge was determined from zeta potential.
4.
2010.06
서비스 종료(열람 제한)
The effects of high-resolution wind profiler (HWP) data on the wind distributions were evaluated in two different coastal areas during the study period (23-26 August, 2007), indicating weak-gradient flows. The analysis was performed using the Weather Research and Forecasting (WRF) model coupled with a three-dimensional variational (3DVAR) data assimilation system. For the comparison purpose, two coastal regions were selected as: a southwestern coastal (SWC) region characterized by a complex shoreline and a eastern coastal (EC) region surrounding a simple coastline and high mountains. The influence of data assimilation using the HWP data on the wind distributions in the SWC region was moderately higher than that of the EC region. In comparison between the wind speed and direction in the two coastal areas, the application of the HWP data contributed to improvement of the wind direction distribution in the SWC region and the wind strength in the EC region, respectively. This study suggests that the application of the HWP data exerts a large impact on the change in wind distributions over the sea and thus can contribute to the solution to lack of satellite and buoy data with their observational uncertainty.
5.
2010.06
서비스 종료(열람 제한)
In this study, we analyzed the impact of orographic and thermal forcing on the atmospheric flow field over the urban metropolitan areas on urban artificial buildings and future development plan. Several numerical experiments have been undertaken in order to clarify the impacts of the future development plan on urban area by analyzing practical urban ground conditions, we revealed that there were large differences in the meteorological differences in each case.
The prognostic meteorological fields over complex areas of Seoul, Korea are generated by the PSU/NCAR mesoscale model(MM5). we carried out a comparative examination on the meteorological fields of topography and land-use that had building information and future development plan. A higher wind speed at daytimes tends to be forecasted when using new topography and land use data that have a high resolution with an appropriate limitation to the mixing height and the nocturnal boundary layer(NCB). During nighttime periods, since radiation cooling development is stronger after development plan, the decreased wind speed is often generated.
6.
2010.06
서비스 종료(열람 제한)
This study is designed to assess the priority order of the chemicals to cause to generate occupational diseases in order to understand the fundamental data required for the preparation of health protective measure for the workers dealing with chemicals. The 41 types of 51 ones of chemicals to cause to generate the national occupational diseases were selected as the study objects by understanding their domestic use or not, and their occupational diseases' occurrence or not among 110,608 types of domestic and overseas chemicals. To assess their priority order the sum of scores was acquired by understanding the actually classified condition based on a perfect score of physical riskiness(90points) and health toxicity(92points) as a classification standard by GHS, the priority order on GHS riskiness assessment, GHS toxicity assessment, GHS toxic․riskiness assessment(sum of riskiness plus toxicity) was assessed by multiplying each result by each weight of occupational disease's occurrence.
The high ranking 5 items of chemicals for GHS riskiness assessment were turned out to be urethane, copper, chlorine, manganese, and thiomersal by order. Besides as a result of GHS toxicity assessment the top fives were assessed to be aluminum, iron oxide, manganese, copper, and cadium(Metal) by order. On the other hand, GHS toxicity․riskiness assessment showed that the top fives were assessed to be copper, urethane, iron oxide, chlorine and phenanthrene by order. As there is no material or many uncertain details for physical riskiness or health toxicity by GHS classification though such materials caused to generate the national occupational diseases, it is very urgent to prepare its countermeasure based on the forementioned in order to protect the workers handling or being exposed to chemicals from health.
7.
2010.06
서비스 종료(열람 제한)
Restraint to drying shrinkage is the most common cause of concrete cracking. In many applications, drying shrinkage cracks are inevitable. In this paper, the surface cracks of soil concrete caused by drying shrinkage were considered to become an one of concrete textures. So, laboratory shrinkage tests were conducted and the results were applied to the field applications. The study results were summarized as follows; First, the use of vinyl sheets and concrete polymers helped to control the concrete cracking. Second, crack propagation usually started at the interfaces of soil concrete slabs and the cracks grew to the inner slabs. Third, surface cracks of soil concrete slabs could be an one of good concrete textures.
8.
2010.06
서비스 종료(열람 제한)
It follows in quality and sewage exclusion method of the investigation objective sector and the Combined Sewer Overflows which is suitable in regional characteristics and the confluence area against the rainfall initially a flow and the medulla and measurement - it analyzes the initial rainfall outflow possibility control plan which is suitable in the domestic actual condition and it proposes the monitor ring plan for the long-term flow and pollution load data accumulation. From the research which it sees the Infiltration water/Influent water and CSOs investigation it passes by the phase of hazard chain and Namwon right time 4 it does not hold reverse under selecting, Measurement it used the hazard automatic flow joint seal Sigma 910 machine and in case 15 minute interval of the I/I, it measured a flow at case 5, 15 minute standing of the CSOs. The water quality investigation for the water leakage investigation of the I/I and the sewage from the point which is identical with flow measurement during on-the-spot inspection duration against 6 items which include the BOD sampling and an analysis, when the rainfall analysis for CSOs fundamental investigation analyzed against 18 items which include the BOD sampling. Consequently, for the optimum interpretation invasion water / inflow water of the this investigation area day average․the lowest flow - water quality assessment veterinarian optimum interpretation hazard average per day - lowest flow - it averages a medulla evaluation law department one lowest flow evaluation technique and it selects, it presentation collectively from here it gets, position result with base flow analysis of invasion water / inflow water.
9.
2010.06
서비스 종료(열람 제한)
Each four polycyclic aromatic hydrocarbons (PAHs) was reacted with OH radical at 1.5 Å distance by CAChe MOPAC 2000 program. These results were compared to those reported experimental results. Reaction positions of all four PAHs corresponded with predicted positions in which ⊿E(HOMO-LUMO) was approximately 4.7. Finally oxygen of OH radical combined with PAH and quinone form of products were produced. These results indicate that the proposed determining the ⊿E(HOMO-LUMO) can be effectively applied to predict reaction position of recalcitrant compounds such as dioxins, PCBs, POPs, and etc.
10.
2010.06
서비스 종료(열람 제한)
Temporal trends of ozone concentration in Jinju were investigated by using observation data from 3 air quality monitoring stations for the period of 2004~2008. In addition, spatial comparisons of ozone concentration at Jeoguri, upwind and downwind directions of Jinju were investigated between May and September 2009.
Annual mean exhibited increasing trends +1.7ppb/yr throughout the study period. In the case of diurnal variation, the lowest ozone concentration was shown from 7 am to 8 am and the highest around 4 pm. The ozone concentrations of Jeoguri station of the south coast were higher than Jinju. In particular, the upwind direction of Jinju had relatively hight ozone concentration.
11.
2010.06
서비스 종료(열람 제한)
The prediction of discharge is very important in water resources management and plan. In this study, we have analyzed discharge data of site at up and down stream in watershed. In order to forecast discharge the regression equations were developed by measuring flow data. Also, to forecast the change of water quality followed by change of inflow the correlation relationship between inflow of the Youngchun site and the Chunhju dam was shown as very high. The forecast of inflow at the Chungju dam would be possible through flow analysis of the Youngchun site. And, it is possible to forecast water quality by flow analysis because the correlation relationship of SS and turbidity followed by change of flow for each station of investigation was very high.
12.
2010.06
서비스 종료(열람 제한)
To solve a problem of water supply on urban areas, groundwater recharge has to be assessed not only for evaluating the possibility of groundwater development but also for identifying a sustainable aquifer system for water resource development. The assessment of groundwater recharge has been challenged since the land use has been changed constantly. In this study, the groundwater recharge and its ratio were assessed from 1961 to 2007 in Su-yeong-gu, Busan, South Korea by analyzing precipitation, land use, and soil characteristics. For land use analysis, the urbanization change was considered. The land use areas for the residential, agricultural, forest, pasture, bare soil, and water in 1975 occupy 18.6 %, 30.0%, 48.8%, 0.1%, 2.0%, and 0.5% of total area, respectively. The land use ratios were sharply changed from 1980 to 1985; the agricultural area was decreased to 18.3%, and the residential area was increased to 15.0%. From 1995 to 2000, the agricultural area was decreased to 5.5%, and the residential area was increased to 5.4%. The annual averages of precipitation, groundwater recharge, and its ratio were 1509.3 mm, 216.0 mm, and 14.3% respectively. The largest amount of the groundwater recharge showed in 1970 as 408.9 mm, comparing to 2138.1 mm of annual rainfall. Also, the greatest ratio of the groundwater recharge was 19.8% in 1984 with 1492.6 mm of annual rainfall. The lowest amount and ratio of the groundwater recharge were 71.9 mm and 8.0% in 1988, relative to 901.5 mm of annual precipitation. As a result, it is concluded that rainfall has increased, whereas groundwater recharge has decreased between 1961 and 2007.
13.
2010.06
서비스 종료(열람 제한)
Nowadays meteorological information is systemized as a useful knowledge which has a significant effect on the overall industrial domains over the simple data. The distribution industry, which has the short life cycle, depends on the meteorological information at the strategic level.
However, it is necessary to pay attention to the continuous investment in meteorological information because there is a hostility to paying for a service, particularly it does not provide accurate and reliable information.
Therefore, the purpose of this study is to increase the usefulness of meteorological information in the distribution industry for its economic effectiveness from the core meteorological factors.
We found significant meteorological factors (temperature, precipitation, disaster) that have a critical influence on the distribution industry through the hierarchical analysis process, and their importance according to the type of distribution channels, such as department store, large-scale discount store, convenience store, and home shopping.
We performed the AHP analysis with 103 survey samples by middle managers from the various distribution channels. We found that precipitation is the critical meteorological factor across the distribution industry. Based on this result, we stress the difference in the level of the meteorological information in order for the effectiveness of each type of distribution channels.
