The aim of this study was to investigate the accumulation of metallic elements and the control effect of marine pollution caused by ocean dumping in the sediments at a waste disposal area in the Yellow Sea. In July 2009, concentrations of organic matter and metallic elements (Al, Fe, As, Cd, Cr, Co, Hg, Ni, Mn, Pb, and Zn) were measured in surface sediments at the site. The ignition loss (IL) in the surface sediments showed a mean value of 15.4%, about 1.5 times higher than the mean value of the sediments in the coastal areas of Korea. The chemical oxygen demand (COD) at some disposal sites exceeded 20 ㎎ O2/g·dry, which signifies the initial concentration of marine sediment pollutants in Japan. The disposal sites contain higher concentrations of Cr, Cu and Zn than the sediments of bays and estuaries that might be contaminated. The magnitude of both metal enrichment factors (EF) and adverse biological effects suggest that pollution with Cr and Ni occurred due to the dumping of waste in the study area. In addition, the geoaccumulation index (Igeo) showed that the surface sediments were moderately contaminated. By the mid-2000s, when the amount of waste dumped at this site was the highest, the concentration of metallic elements was higher than ever recorded. On the other hand, in 2008-09, the need for environmental management was relatively low compare with the peak. As a result, the quality of marine sediment has been enhanced, considering the effect of waste reduction and natural dilution in the disposal area.
To improve the physical and chemical properties of the soil and increasing water-retaining property of the soil, Superabsorbent synthetic polymeric materials have been used. The experiment carried out from April to July 2012 after the influence evaluation of Superabsorbent synthetic polymeric materials to vines plant. The result shows that the study of Hedera japonica Tobler, the growth and the survival rates rank as media > hydroponic > superabsorbent synthetic polymers, and the growth and the survival rates are considerably pessimistic in the experiment of hydroponic and superabsorbent synthetic polymers. In the study of Trachelospermum asiaticum var. intermedium, the growth and the survival rates rank as hydroponic > media > superabsorbent synthetic polymers, the difference between the experiment of hydroponic and is very small and the survival rates are not very good in the experiment of superabsorbent synthetic polymers. In the study of Euonymus fortunei var. radicans Rehder,it is insignificantly difference among the different of planting based. Judging from these results, the differences are depending on the species of plants. The thesis holds that the characteristics of plant should be considered in plant cultivation and soil improvement in the future, and it is desirable to use the appropriate mixing ratio of soil in soil improvement as well.
A purpose of this study was to provide the helpful information about operation of revised science curriculum by analyzing many contents about acid rain with various aspects, which was written in science textbook of 10 year according to the 7th national curriculum.
The results show that there was the lack of educational systemicity among elementary school, middle school, and high school science curriculum and the lack of explanation for occurrence and standard level of acid rain, pH 5.6. And It could be categorized the effect of acid rain into four groups and experiment or experiment activities into three groups.
Emissions of air pollutants and greenhouse gases (GHGs) from aircraft activities at 11 small-scale airports were investigated using the emissions and dispersion modeling system (EDMS) version 5.1.3 during the two year period of 2009~2010. The number of landing and take-off (LTO) at these airports was dominant for the aircraft type B737, accounting for more than 60% of the total LTOs. Out of the 11 small-scale airports, Gwangju (GJ, RKJJ) airport was the largest emitter of air pollutants and GHGs, whereas Yangyang (YY, RKNY) airport was the smallest emitter. The emissions of NOx and VOCs in 2010 at the 11 airports ranged from 1.9 to 83 ton/y and 0.1 to 17 ton/y, respectively. In 2010, the emissions of CO2 ranged from 394 to 21,217 ton/y. The emissions of most air pollutants (except for NOx and PM10) and GHGs were estimated to be the highest in taxi-out mode. The highest emissions of NOx and PM10 were emitted from climb-out and approach modes, respectively. In addition, the total LTOs at the 11 small-scale airports accounted for the range of 9.3~9.9% of those at four major international airports in Korea. The total emissions of air pollutants and GHGs at the 11 airports ranged from 4.8 to 12% of those at the four major airports.
This study was designed to synthesize mesoporous carbon, porous carbonic material and to characterize its surface in an attempt to adsorption methane gas(CH4). Synthesis of mesoporous carbon was carried out under two steps ; 1. forming a RF-silica complex with a mold using CTMABr, a surfactant, and TEOS, raw material of silica, and 2. eliminating silica through carbonization and HF treatment. The mesoporous carbon was synthesized under various conditions of synthesis time and calcination. Eight different types of mesoporous carbon, which were designated as MC1, MC2, MC3, MC4, MCT1, MCT2, MCT3, and MCT4, were prepared depending upon preparation conditions. The analysis of mesoporous carbon characteristics showed that the calcination of silica stabilized the mixed structure of silica and carbonic complex, and made the particle uniform. The results also showed that hydrothermal synthesis time did not have a strong influence on the size of pore. The bigger specific surface area was obtained as the hydrothermal synthesis time was extended. However, the specific surface area was getting smaller again after a certain period of time. In adsorption experiments, CH4 was used as adsorbate. For the case of CH4, MCT3 showed the highest adsorption efficiency.
Functionalized adsorbent has been synthesized by piperazine(Pz) on activated carbon. Quantitative estimations of CO2 were undertaken using gas chromatography with GC/TCD and the prepared adsorbents were characterized by BET surface area and FT-IR. It was also studied effect of various parameters such as piperazine loadings and adsorption temperature. The specific surface area decreased from 1212.0 m2/g to 969.8 m2/g by impregnation and FT-IR revealed a N-H functional group at about 1400 cm-1 to 1700 cm-1. The CO2 adsorption capacity at 20℃ and 50∼100℃ was as follow: AC > Pz(10)-AC> Pz(30)-AC> Pz(50)-AC at 20℃ and Pz(10)-AC > AC > Pz(30)-AC> Pz(50)-AC at 50∼100℃. Therefore, for high temperature flue gas condition, the Pz(10)-AC showed the highest adsorption capacity due to physical adsorption and chemical adsorption by amino-group content. The results suggest that activated carbon impregnated with Pz is an effective adsorbent for CO2 capture from real flue gases above 50℃.
Although antioxidant activities of Korean traditional fermented foods were reported by many researchers, study on antioxidant activity of microorganism originated from Korean traditional fermented foods was little. Therefore, we improved condition for antioxidant production by a bacterium isolated from home-made Chungkookjang. We selected a bacterial strain, which showed the highest antioxidative activity, from Chungkookjang and then named GJ. The selected GJ strain was identified as Bacillus methylotrophicus by alignment data of 16S rRNA gene nucleotide sequences. Improved medium compositions for DPPH radical scavenging activity were 0.25% sucrose, 1% peptone, 0.01% MgSO4·7H2O and initial pH 6.5, respectively. Optimal culture conditions were 30℃, 200 rpm and 4% inoculum volume, respectively. In improved conditions, DPPH radical scavenging activity of GJ reached to 91% in a short time. The strain GJ also possessed ACE inhibition and other antioxidative activities; ACE inhibition activity (49.4%), ABTS radical scavenging activity (99.8%), metal chelating activity (67.9%), SOD-like activity (36.5%) and reducing power (A700 = 5.982) were observed, respectively. Therefore, our results suggest that B. methylotrophicus GJ strain may be potential candidate for functional foods, cosmetic products for anti-aging and medicine for diseases caused by oxidative stress.
Dielectric discharges are an emerging technique in environmental pollutant degradation, which that are characterized by the production of hydroxyl radicals as the primary degradation species. For practical application of the plasma reactor, reactor that can handle large amounts of water are needed. Plasma research to date has focused on small-scale water treatment. This study was carried out basic study for scale-up of a single DBD (dielectric barrier discharge) plasma reactor. The degradation of N, N-Dimethyl-4-nitrosoaniline (RNO, indicator of the generation of OH radical) was used as a performance indicator of multi-plasma reactor. The experiments is divided into two parts: design parameters [effect of distance of single plasma module (1~14 cm), arrangement of ground electrode (single and multi), rector number (1~5) and power number (1~5)]; operation parameter [effect of applied voltage (60~220 V), air flow rate (1~5 L/min), electric conductivity of solution (1.4 μS/cm, deionized water)~18.8 mS/cm (addition of NaCl 10 g/L) and pH (5~9)]. Considering the electric stability of the plasma reactor, optimum spacing between the single plasma module was 2 cm. Multi discharge electrodes - single ground electrode array was selected. Combination of power 3-plasma module 5 was the optimal combination for maximum RNO degradation. The optimum 1st voltage and air flow rate for RNO degradation were 180 V and 4 L/min, respectively. The pH and conductivity of the solution was not influencing the RNO degradation.
This study was carried out to establish the conservation plan of specific plants by surveying and analyse the individuals and the environment of habitats on specific plants designated by Juwangsan national park office. The specific plants were 14 species including Berchemia berchemiaefolia, Hylotelephium ussuriense, Aristolochia manshuriensis, Lilium cernuum, Thalictrum coreanum, Exochorda serratifolia, Lilium distichum, Aristolochia contorta, Jeffersonia dubia, Eleutherococcus senticosus, Salix chaenomeloids, Eranthis stellata, Scopolia japonica, and Paeonia japonica. The habitats of specific plants were 40 sites including Berchemia berchemiaefolia of 11 sites, Hylotelephium ussuriense of 8 sites, Lilium cernuum and Thalictrum coreanum of each 3 sites, Exochorda serratifolia of 2 sites, and Lilium distichum, Aristolochia contorta, Jeffersonia dubia, Eleutherococcus senticosus, Salix chaenomeloids, Eranthis stellata, Scopolia japonica and Paeonia japonica of each 1 site. The altitude was the most in 300~400 m. In direction, NW was the most, and it showed SW in that order. The slope angle was the most in 0~10%, and the cliff showed in that order. In the results of species composition by stratum layer, Berchemia berchemiaefolia had the most, 15 species, in tree layer. In shrub and herb layer, this had the most as 20 species and 29 species, too. The species that occupied the largest size was Salix chaenomeloids in 2,500 ㎡, and Jeffersonia dubia showed 1,500 ㎡in that order. The conservation of specific plants is to accomplish the ex situ and in situ conservation at the same time.
The purpose of this study was to analyze the effects of partial solar eclipse on 21 May 2012 in Korea on meteorological variables in Busan. 0800 LST(Local Standard Time) solar radiation was similar or lower than 0700 LST solar radiation, and sunshine duration decreased by 0.2∼0.5 hours in Busan and great cities under the influence of the partial solar eclipse. Temperature drop due to the partial solar eclipse was 0.2∼2.0℃, time taken to arrive at maximum temperature after onset of eclipse was 8∼62 minutes, and time taken to arrive at minimum temperature after maximum eclipse was -9∼17 minutes in Busan. Change of wind speed was negligible as partial solar eclipse occurred in the morning. Soil temperature of 5 ㎝was minute as well, the increase of soil temperature due to sunset was delayed by more than 1 hour.
This study analyzed on characteristics of the ground-water capture zone in coastal areas and mid-mountainous area according to pumping rate. For this study, it targeted Jejudo island where is the volcanic island. To analyze, MODFLOW model and MODPATH model, which are the ground-water flow analysis models, were used. As a result of research, the following conclusions could be obtained. As a result of analyzing influence of a change in pumping time upon length of capture zone, the length of capture zone in coastal area was indicated to be greater in the changing ratio compared to the length of capture zone in mid-mountainous area. Next, in the coastal area, the pumping rate and the capture-zone length are changing similarly. However, in mid-mountainous area, the length of capture zone was indicated to grow when the pumping rate comes to exceed 1,500m3/day. As a result of analyzing influence of a change in pumping time upon capture area, the tendency of a change in the area was indicated similarly in coastal areas and mid-mountainous area. Especially, it could be known that the larger pumping rate leads to the more definite increase in tendency to a change in capture area. Based on this study, it was allowed to be possibly used in the suitable pumping rate in coastal areas and mid-mountainous area of the volcano island in the future. A follow-up research is judged to necessarily analyze the influence of tubular-well group upon capture zone by additionally analyzing a change in capture zone targeting the concentrated tubular well.
We compared the applicability and economical efficiency of peroxone process with those of ozone process in the existing water treatment plant on downstream of Nakdong River. After comparing the peroxone process for removing geosmin with the ozone process in lab scale test, peroxone process showed much higher removal efficiency than the ozone process at the same ozone dosage. Proper range of H2O2/O3 ratio were 0.5~1.0 and the half-life of geosmin was about 5.5~6.8 min when the H2O2/O3 ratio was set to 0.5 during 1~2 mg/L of ozone dosage. Peroxone process could reduce the ozone dosage about 50 to maximum 30% for the same geosmin removal efficiency compared to the ozone process in the pilot scale test. In case of 1,4-dioxane treatment, peroxone process could have 3~4 times higher efficiency than ozone process at the same ozone dosage. The results of estimating the economical efficiency of ozone and peroxone process for treating geosmin and 1,4-dioxane by using pilot scale test, in case of the removal target was set to 85% for these two materials, the cost of peroxane process could be reduced about 1.5 times compared to ozone process, and in the same production cost peroxone process could have 2~3 times higher removal efficiency than ozone process. The removal efficiency by peroxone process showed a large difference depending on the physicochemical characteristics of target materials and raw water, therefore detailed examination should be carried out before appling peroxone process.
Decomposition of non-biodegradable contaminants such as phenol contained in water was investigated using a dielectric barrier discharge (DBD) plasma reactor in the aqueous solutions with continuous oxygen bubbling. Effects of various parameters on the removal of phenol in aqueous solution with high-voltage streamer discharge plasma are studied. In order to choose plasma gas, gas of three types (argon, air, oxygen) were investigated. After the selection of gas, effects of 1st voltage (80 ~220 V), oxygen flow rate (2 ~7 L/min), pH (3 ~11), and initial phenol concentration (12.5 ~100.0 mg/L) on phenol degradation and change of UV254 absorbance were investigated. Absorbance of UV254 can be used as an indirect indicator of phenol degradation and the generation and disappearance of the non-biodegradable organic compounds. Removal of phenol and COD were found to follow pseudo first-order kinetics. The removal rate constants for phenol and COD of phenol were 5.204 × 10-1 min-1 and 3.26 × 10-2 min-1, respectively.