간행물
한국재료학회지 KCI 등재 SCOPUS Korean Journal of Materials Research
- 발행기관 한국재료학회
- 자료유형 학술지
- 간기 월간
- ISSN 2799-8525 (Print)2799-8681 (Online)
- 수록기간 1991 ~ 2024
- 주제분류 공학 > 재료공학 공학 분류의 다른 간행물
- 십진분류KDC 530DDC 620
권호리스트/논문검색
제25권 제10호 (2015년 10월) 12건
1.
2015.10
구독 인증기관 무료, 개인회원 유료
In this work, ceramic coatings were prepared on Al7075 aluminum alloy using microarc oxidation (MAO) process in a silicate-fluoride based electrolyte solution. The effect of OH− concentration, by adding NaOH to the solution on the microstructural and mechanical properties of the coating was investigated. Surface morphology and cross sectional view of the coating was analyzed using SEM while XRD was used to examine the phase compositions of the coatings. From XRD α-Al2O3 phase was found to be increased by adding NaOH to the electrolyte. Thereby, the hardness and the wear properties of the MAO coatings were found to be superior to those of the coatings prepared without NaOH addition or with amount maximum than 2 g/l NaOH. Moreover, the morphology of the coatings was transformed form nodule-based cluster to crater based structure with the addition of NaOH to the MAO electrolyte solution.
4,000원
2.
2015.10
구독 인증기관 무료, 개인회원 유료
MAO ceramic coatings were prepared on AZ61 magnesium alloy for various processing times ranging from 5 to 60 min, in an electrolyte solution based on silicate-fluoride. The mechanical, electrochemical and, microstructural properties and the phase compositions of the coating layers were investigated. In this work, unlike previous studies, coatings with high amounts of the Mag2SiO4 phase were formed which contained small amounts of MgO and MgF2 at a processing condition of 30 min. A microstructural analysis revealed that the porosity of the coatings was reduced considerably with an increase in the processing time, together with a change in the pore geometry from an irregular to a spherical shape. Potentiodynamic polarization and mechanical testing results showed that the coatings acquired after a processing time of 30 min were superior to all of the others.
4,000원
3.
2015.10
구독 인증기관 무료, 개인회원 유료
Aging aircraft structures are inevitably exposed to environment for a long time facing many potential problems, including corrosion and wide spread fatigue damage, which in turn cause the degradation of flight safety. In this study, the environmental surface damages on aging aircraft structures induced during service were quantitatively analyzed. Additionally, S-N fatigue tests were performed with center hole specimens extracted from aging aircraft structures. From the results of quantitative analyses of the surface damages and fatigue tests, it is concluded that corrosion pits initiated during service reduce the fatigue life significantly. Finally, using the fracture mechanics and the EIFS (equivalent initial flaw size) concepts, the remaining fatigue life was predicted based on actual fatigue test results.
4,000원
4.
2015.10
구독 인증기관 무료, 개인회원 유료
Electricity generation through fossil fuels has caused environmental pollution. To solve this problem, research on new renewable energy (solar, wind, geothermal heat, etc.) to replace fossil fuels is in progress. These devices are able to consistently generate power. However, they have many drawbacks, such as high installation costs and limitations in possible set-up environments. Thus, piezoelectric harvesting technology, which is able to overcome the limitations of existing energy technologies, is actively being studied. Piezoelectric harvesting technology uses the piezoelectric effect which occurs in crystals that generate voltage when stress is applied. Therefore, it has advantages such as a wider installation base and lower technological cost. In this study, a piezoelectric energy harvesting device based on constant wave motion was investigated. This device can regenerate electricity in a constant turbulent flow in the middle of the sea. The components of the device are circuitry, a steel bar, an bimorph piezoelectric element and buoyancy elements. In addition, a multiphysical analysis coupled with the structure and piezoelectric elements was conducted to estimate the performance of the device. With this piezoelectric energy harvesting device, the displacement and electric power were analyzed.
4,000원
5.
2015.10
구독 인증기관 무료, 개인회원 유료
GNPs have several excellent mechanical properties including high strength, a good young’s modulus, thermal conductivity, corrosion resistance, electronic shielding, etc. In this study, CF/GNP/Epoxy composites were manufactured using GNP weight ratios of 0.15 wt%, 0.3 wt%, 0.5 wt%, 0.7 wt% and 1 wt%. The composites were manufactured with a mechanical method (3-roll-mill). Tensile, impact and wear tests were performed according to ASTM standards D3039, D256 and D3181, respectively. The results show that the CF/GNP0.3wt%/Epoxy composites have good mechanical properties, e.g., tensile strength and impact and wear resistance. In this study, both carbon fabric and GNPs were used as reinforcements in the composites. The mechanical properties increased and weight loss decreased as the GNP content in the resin films was increased.
4,000원
6.
2015.10
구독 인증기관 무료, 개인회원 유료
One-dimensional (1D) silver nanostructures, which possess the highest conductivity among all room-temperature materials, moderate flexibility and high transmittance, are one of the most promising candidate materials to replace conventional indium tin oxide transparent electrodes. However, the short length and large diameter of 1D silver nanostructures cause a substantial decrease in the optical transparency or an increase in the sheet resistance. In this work, ultra-long silver nanofiber networks were synthesized with a low-cost and scalable electrospinning process, and the diameter of the nanofibers were finetuned to achieve a higher aspect ratio. The decrease in the diameter of the nanofibers resulted in a higher optical transparency at a lower sheet resistance: 87 % at 300 Ω/sq, respectively. It is expected that an electrospun silver nanofiber based transparent electrode can be used as a key component in various optoelectronic applications.
4,000원
7.
2015.10
구독 인증기관 무료, 개인회원 유료
TiO2 nanowires were grown by thermal oxidation of TiO powder in an oxygen and nitrogen gas environment at 1000 oC. The ratio of O2 to N2 in an ambient gas was changed to investigate the effect of the gas ratio on the growth of TiO2 nanowires. The oxidation process was carried out at different O2/N2 ratios of 0/100, 25/75, 50/50 and 100/0. No nanowires were formed at O2/N2 ratios of less than 25/75. When the O2/N2 ratio was 50/50, nanowires started to form. As the gas ratio increased to 100/0, the diameter and length of the nanowires increased. The X-ray diffraction pattern showed that the nanowires were TiO2 with a rutile crystallographic structure. In the XRD pattern, no peaks from the anatase and brookite structures of TiO2 were observed. The diameter of the nanowires decreased along the growth direction, and no catalytic particles were detected at the tips of the nanowires which suggests that the nanowires were grown with a vapor-solid growth mechanism.
3,000원
8.
2015.10
구독 인증기관 무료, 개인회원 유료
The present study prepared molybdenum trioxide (MoO3), the most important intermediate of molybdenum metal, by using a fluidized bed reactor for the thermal decomposition of ammonium molybdate (AM) in the presence of an air flow. During the process of fluidizing the sample inside the reactor, the reaction time and temperature were optimized with a close analysis of the X-ray diffraction (XRD) data and with thermogravimetric analysis (TGA). In particular, the temperature level, at which the AM decomposition is completed, is very important as a primary operating parameter. The analysis of the XRD and TGA data showed that the AM decomposition is almost completed at ~350 oC with a reaction time of 30 min. A shorter reaction time of 10 min. required a higher reaction temperature of ~500 oC with the same air flow rate to complete the AM decomposition. A sharp rise in the decomposition efficiency at a temperature ranging between 320 and 350 oC indicated a threshold for the AM decomposition. The operating conditions determined in this study can be used for future scale-ups of the process.
4,000원
9.
2015.10
구독 인증기관 무료, 개인회원 유료
The mechanical properties and microstructures of Aluminum 6056 alloys were investigated for their use in the fabrication of a piton block. The EN-AW6056 alloys exhibited a tensile strength of 375 MPa for a solution treatment temperature of 550 oC for 2 h followed by an aging treatment at 190 oC for 4 h. The microstructures of the heat treated specimen showed that the Mg2Si phase with a size of 3~5 um was dispersed throughout the aluminum matrix when the heat treatment was done. Moreover, in order to identify the forgeability of the specimen, upsetting tests were done. For up to 80 % of the upsetting ratio, the specimen maintained its original shape, and at above 80 % of the upsetting ratio, the specimen underwent crack development. The specimen was successfully forged without any defects with the examined material conditions. The material conditions together with the forging conditions are discussed in terms of the microstructures and mechanical properties.
4,000원
10.
2015.10
구독 인증기관 무료, 개인회원 유료
The ductile-brittle transition behavior of two austenitic Fe-18Cr-10Mn-N-C alloys with different grain sizes was investigated in this study. The alloys exhibited a ductile-brittle transition behavior because of an unusual brittle fracture at low temperatures unlike conventional austenitic alloys. The alloy specimens with a smaller grain size had a higher yield and tensile strengths than those with a larger grain size due to grain refinement strengthening. However, a decrease in the grain size deteriorated the low-temperature toughness by increasing the ductile-brittle transition temperature because nitrogen or carbon could enhance the effectiveness of the grain boundaries to overcome the thermal energy. It could be explained by the temperature dependence of the yield stress based on low-temperature tensile tests. In order to improve both the strength and toughness of austenitic Fe-Cr-Mn-N-C alloys with different chemical compositions and grain sizes, more systematic studies are required to understand the effect of the grain size on the mechanical properties in relation to the temperature sensitivity of yield and fracture stresses.
4,000원
11.
2015.10
구독 인증기관 무료, 개인회원 유료
Ali Hussain, Adnan Maqbool, Rizwan Ahmed Malik, Arif Zaman, Jae Hong Lee, Tae Kwon Song, Jae Hyun Lee, Won Jeong Kim, Myong Ho Kim
Bi0.5Na0.5TiO3 (BNT) based ceramics are considered potential lead-free alternatives for Pb(Zr,Ti)O3(PZT) based ceramics in various applications such as sensors, actuators and transducers. However, BNT-based ceramics have lower electromechanical performance as compared with PZT based ceramics. Therefore, in this work, lead-free bulk 0.99[(Bi0.5Na0.5)0.935Ba0.065](1-x)LaxTiO3-0.01SrZO3 (BNBTLax-SZ, with x = 0, 0.01, 0.02) ceramics were synthesized by a conventional solid state reaction The crystal structure, dielectric response, degree of diffuseness and electric-field-induced strain properties were investigated as a function of different La concentrations. All samples were crystallized into a single phase perovskite structure. The temperature dependent dielectric response of La-modified BNBT-SZ ceramics showed lower dielectric response and improved field-induced strain response. The field induced strain increased from 0.17% for pure BNBT-SZ to 0.38 % for 1 mol.% La-modified BNBT-SZ ceramics at an applied electric field of 6 kV/mm. These results show that Lamodified BNBT-SZ ceramic system is expected to be a new candidate material for lead-free electronic devices.
4,000원
12.
2015.10
구독 인증기관 무료, 개인회원 유료
The effects of coating thickness on the delamination and fracture behavior of thermal barrier coating (TBC) systems were investigated with cyclic flame thermal fatigue (FTF) and thermal shock (TS) tests. The top and bond coats of the TBCs were prepared by electron beam-physical vapor deposition and low pressure plasma spray methods, respectively, with a thickness ratio of 2:1 in the top and bond coats. The thicknesses of the top coat were 200 and 500 μm, and those of the bond coat were 100 and 250 μm. FTF tests were performed until 1140 cycles at a surface temperature of 1100 oC for a dwell time of 5 min. TS tests were also done until more than 50 % delamination or 1140 cycles with a dwell time of 60 min. After the FTF for 1140 cycles, the interface microstructures of each TBC exhibited a sound condition without cracking or delamination. In the TS, the TBCs of 200 and 500 μm were fully delaminated (> 50 %) within 171 and 440 cycles, respectively. These results enabled us to control the thickness of TBC systems and to propose an efficient coating in protecting the substrate in cyclic thermal exposure environments.
4,000원
